Dell W-IAP224/225 User guide

Brand: Dell

Model: W-IAP224/225

Type: User guide

The Dell W-IAP224/225 is a versatile and high-performance access point designed to provide reliable and secure wireless connectivity in various environments. With its dual-band capabilities, it can simultaneously operate on both 2.4 GHz and 5 GHz frequencies, ensuring optimal performance and minimizing interference. The device supports multiple AP models and offers flexible Ethernet cable routing options, making it suitable for a wide range of deployment scenarios.

AP-220-MNT-W2 Wall Mount Kit

Installation Guide

0511290-02 | August 2013 1

Package Contents

 AP-220-MNT-W2 Mounting Bracket

 2x Ethernet Cable Adapter

 T8 Torx Security Screw

Installation

Complete the following steps to install your access point using the AP-220-MNT-W2.

Ethernet Cable Routing Options

There are three options for routing the Ethernet cable depending the placement of your AP in relation to the

source of the Ethernet cable.

Ethernet Cable From Below AP

1. Route the Ethernet cable(s) through the channel in the rear of the mount.

2. Loop the Ethernet cable(s) over the top of the mount and direct the cable(s) through the opening leading

to the AP’s Ethernet ports.

3. If required, route the power cable through the bottom right of mounting bracket.

4. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.

Figure 1 Ethernet cable from below the AP

This mount kit supports multiple AP models. All installation images show the 225 AP.

AP-220_22

2 AP-220-MNT-W2 Wall Mount Kit | Installation Guide

Ethernet Cable Behind AP

1. Route the Ethernet cable(s) through the large opening in the center of the mount.

2. If required, route the power cable through the bottom right of mounting bracket.

3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.

Figure 2 Ethernet cable behind AP

Using The Ethernet Cable Adapter

1. Install Ethernet cable adapter(s) by sliding the female end of the adapter into the slot behind the access

on the side of the mounting bracket. The adapter is secured when it clicks into place.

2. If required, route the power cable through the bottom right of mounting bracket.

3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.

Figure 3 Using the Ethernet cable adapter

AP-220_23

AP-220_24

AP-220-MNT-W2 Wall Mount Kit | Installation Guide 3

Installing the Mounting Bracket

1. Install any necessary wall anchors. Wall anchors are not included in this kit.

2. Align the screw holes in the mounting bracket with the previously installed anchors or demarcated

screw points.

3. Insert the screws to secure the mounting bracket. Screws are not included in this kit. Ensure that no

Ethernet cable(s) are obstructing the screw holes.

Figure 4 Attaching the Adapter to a Wall

4. Attach any necessary cables and/or antennas to the AP.

5. If using the Ethernet cable adapter, connect Ethernet cable(s) through the openings on the side of the

mounting bracket.

6. Push the metal slider up to allow the AP to connect.

7. While still pushing the metal slider, align the mounting posts on the bracket with the mounting holes

shown in Figure 5.

8. Install the T8 Torx security screw into the screw hole on the bottom of the mounting bracket, next to

slider to complete the installation.

AP-220_19

To disconnect Ethernet cable(s) from the adapter after the installation is complete, you must remove the AP from

the bracket to access the RJ45 locking tab.

4 AP-220-MNT-W2 Wall Mount Kit | Installation Guide

Figure 5 Attaching the AP to the Mounting Bracket

Figure 6 Completed Installation

AP-220_20

AP-220_21

Dell W-IAP224/225 User guide

Dell W-IAP224/225 User guide

Dell W-IAP224/225 User guide

Related papers

Other documents