Aruba AP-220-MNT-W2 is a versatile mounting kit designed to provide flexible installation options for various Aruba AP models, including the 225 AP. With its robust construction and thoughtful design, this kit empowers you to securely mount your access points in diverse environments, ensuring optimal performance and seamless connectivity.
Key Features:
- Versatile Mounting Options: Supports multiple mounting scenarios, allowing you to install your AP on walls, ceilings, or poles, adapting to various deployment requirements.
- Ethernet Cable Routing Flexibility: Offers three distinct options for routing Ethernet cables, accommodating different cable management needs and ensuring a clean and organized installation.
Aruba AP-220-MNT-W2 is a versatile mounting kit designed to provide flexible installation options for various Aruba AP models, including the 225 AP. With its robust construction and thoughtful design, this kit empowers you to securely mount your access points in diverse environments, ensuring optimal performance and seamless connectivity.
Key Features:
- Versatile Mounting Options: Supports multiple mounting scenarios, allowing you to install your AP on walls, ceilings, or poles, adapting to various deployment requirements.
- Ethernet Cable Routing Flexibility: Offers three distinct options for routing Ethernet cables, accommodating different cable management needs and ensuring a clean and organized installation.
AP-220-MNT-W2 Mounting Kit
Installation Guide
0511290-05 | October 2014 1
Package Contents
AP-220-MNT-W2 Mounting Bracket
Plastic Shim
2x Ethernet Cable Adapter
T10 Torx Security Screw
Installation
Complete the following steps to install your access point using the AP-220-MNT-W2.
Ethernet Cable Routing Options
There are three options for routing the Ethernet cable depending the placement of your AP in relation to the
source of the Ethernet cable.
Ethernet Cable From Below AP
1. Route the Ethernet cable(s) through the channel in the rear of the mount.
2. Loop the Ethernet cable(s) over the top of the mount and direct the cable(s) through the opening leading
to the AP’s Ethernet ports.
3. If required, route the power cable through the bottom right of mounting bracket.
4. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 1 Ethernet cable from below the AP
NOTE
This mount kit supports multiple AP models. All installation images show the 225 AP.
2 AP-220-MNT-W2 Mounting Kit | Installation Guide
Ethernet Cable Behind AP
1. Route the Ethernet cable(s) through the large opening in the center of the mount.
2. If required, route the power cable through the bottom right of mounting bracket.
3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 2 Ethernet cable behind AP
Using The Ethernet Cable Adapter
1. Install Ethernet cable adapter(s) by sliding the female end of the adapter into the slot behind the access
on the side of the mounting bracket. The adapter is secured when it clicks into place.
2. If required, route the power cable through the bottom right of mounting bracket.
3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 3 Using the Ethernet cable adapter
AP-220-MNT-W2 Mounting Kit | Installation Guide 3
Installing the Mounting Bracket
1. Install any necessary wall anchors. Wall anchors are not included in this kit.
2. Align the screw holes in the mounting bracket with the previously installed anchors or demarcated
screw points.
3. Insert the screws to secure the mounting bracket. Screws are not included in this kit. Ensure that no
Ethernet cable(s) are obstructing the screw holes.
Figure 4 Attaching the Adapter to a Wall
4. Attach any necessary cables and/or antennas to the AP.
5. If using the Ethernet cable adapter, connect Ethernet cable(s) through the openings on the side of the
mounting bracket.
6. Push the metal slider up to allow the AP to connect.
7. While still pushing the metal slider, align the mounting posts on the bracket with the mounting holes
shown in Figure 5.
8. Install the T10 Torx security screw into the screw hole on the bottom of the mounting bracket, next to
slider to complete the installation.
NOTE
If you are installing the mount onto a wall box, position the plastic shim between the box and mount with screw
holes aligned as shown in Figure 4.
NOTE
To disconnect Ethernet cable(s) from the adapter after the installation is complete, you must remove the AP from
the bracket to access the RJ45 locking tab.
4 AP-220-MNT-W2 Mounting Kit | Installation Guide
Figure 5 Attaching the AP to the Mounting Bracket
Figure 6 Completed Installation
-
1
-
2
-
3
-
4
Aruba AP-220-MNT-W2 is a versatile mounting kit designed to provide flexible installation options for various Aruba AP models, including the 225 AP. With its robust construction and thoughtful design, this kit empowers you to securely mount your access points in diverse environments, ensuring optimal performance and seamless connectivity.
Key Features:
- Versatile Mounting Options: Supports multiple mounting scenarios, allowing you to install your AP on walls, ceilings, or poles, adapting to various deployment requirements.
- Ethernet Cable Routing Flexibility: Offers three distinct options for routing Ethernet cables, accommodating different cable management needs and ensuring a clean and organized installation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Dell W-AP114/115 User guide
-
Dell W-IAP224/225 User guide
-
Dell W-AP134/135 User guide
-
Dell W-AP224/225 User guide
-
-
-
Aruba Networks W-AP105 Installation guide
-
Meru Networks 4339B Installation guide
-
-
Dell EMC PowerSwitch N2200-ON Series Installation guide
