Dell W-AP224/225 User guide

Type
User guide

Dell W-AP224/225 is a versatile access point that offers secure and reliable wireless connectivity for various environments. It features dual-band operation, supporting both 2.4 GHz and 5 GHz frequencies, ensuring seamless roaming and improved performance for bandwidth-intensive applications. The device includes multiple Ethernet cable routing options, enabling flexible installation in different scenarios. With its robust design and T8 Torx security screw, it provides secure mounting and theft deterrence.

Dell W-AP224/225 is a versatile access point that offers secure and reliable wireless connectivity for various environments. It features dual-band operation, supporting both 2.4 GHz and 5 GHz frequencies, ensuring seamless roaming and improved performance for bandwidth-intensive applications. The device includes multiple Ethernet cable routing options, enabling flexible installation in different scenarios. With its robust design and T8 Torx security screw, it provides secure mounting and theft deterrence.

AP-220-MNT-W2 Wall Mount Kit
Installation Guide
0511290-02 | August 2013 1
Package Contents
AP-220-MNT-W2 Mounting Bracket
2x Ethernet Cable Adapter
T8 Torx Security Screw
Installation
Complete the following steps to install your access point using the AP-220-MNT-W2.
Ethernet Cable Routing Options
There are three options for routing the Ethernet cable depending the placement of your AP in relation to the
source of the Ethernet cable.
Ethernet Cable From Below AP
1. Route the Ethernet cable(s) through the channel in the rear of the mount.
2. Loop the Ethernet cable(s) over the top of the mount and direct the cable(s) through the opening leading
to the AP’s Ethernet ports.
3. If required, route the power cable through the bottom right of mounting bracket.
4. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 1 Ethernet cable from below the AP
This mount kit supports multiple AP models. All installation images show the 225 AP.
AP-220_22
2 AP-220-MNT-W2 Wall Mount Kit | Installation Guide
Ethernet Cable Behind AP
1. Route the Ethernet cable(s) through the large opening in the center of the mount.
2. If required, route the power cable through the bottom right of mounting bracket.
3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 2 Ethernet cable behind AP
Using The Ethernet Cable Adapter
1. Install Ethernet cable adapter(s) by sliding the female end of the adapter into the slot behind the access
on the side of the mounting bracket. The adapter is secured when it clicks into place.
2. If required, route the power cable through the bottom right of mounting bracket.
3. Install the mounting bracket as described in “Installing the Mounting Bracket” on page3.
Figure 3 Using the Ethernet cable adapter
AP-220_23
AP-220_24
AP-220-MNT-W2 Wall Mount Kit | Installation Guide 3
Installing the Mounting Bracket
1. Install any necessary wall anchors. Wall anchors are not included in this kit.
2. Align the screw holes in the mounting bracket with the previously installed anchors or demarcated
screw points.
3. Insert the screws to secure the mounting bracket. Screws are not included in this kit. Ensure that no
Ethernet cable(s) are obstructing the screw holes.
Figure 4 Attaching the Adapter to a Wall
4. Attach any necessary cables and/or antennas to the AP.
5. If using the Ethernet cable adapter, connect Ethernet cable(s) through the openings on the side of the
mounting bracket.
6. Push the metal slider up to allow the AP to connect.
7. While still pushing the metal slider, align the mounting posts on the bracket with the mounting holes
shown in Figure 5.
8. Install the T8 Torx security screw into the screw hole on the bottom of the mounting bracket, next to
slider to complete the installation.
AP-220_19
To disconnect Ethernet cable(s) from the adapter after the installation is complete, you must remove the AP from
the bracket to access the RJ45 locking tab.
4 AP-220-MNT-W2 Wall Mount Kit | Installation Guide
Figure 5 Attaching the AP to the Mounting Bracket
Figure 6 Completed Installation
AP-220_20
AP-220_21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Dell W-AP224/225 User guide

Type
User guide

Dell W-AP224/225 is a versatile access point that offers secure and reliable wireless connectivity for various environments. It features dual-band operation, supporting both 2.4 GHz and 5 GHz frequencies, ensuring seamless roaming and improved performance for bandwidth-intensive applications. The device includes multiple Ethernet cable routing options, enabling flexible installation in different scenarios. With its robust design and T8 Torx security screw, it provides secure mounting and theft deterrence.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI