Trendnet RB-TPE-P521ES User guide

Category
Network switches
Type
User guide

This manual is also suitable for

TRENDnet User’s Guide
Cover Page
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
i
Contents
Product Overview ........................................................................... 1
Package Contents .......................................................................................................... 1
Features ......................................................................................................................... 1
Product Hardware Features........................................................................................... 2
LED Indicators ................................................................................................................ 3
Switch Installation .......................................................................... 3
Desktop Hardware Installation ...................................................................................... 3
Basic IP Configuration .................................................................................................... 4
Connect additional devices to your switch .................................................................... 6
Accessing switch management interfaces ........................................ 7
Access your switch web management page .................................................................. 7
System Info .................................................................................................................... 7
View your switch status information ................................................................... 7
System ............................................................................................ 9
System Management ..................................................................................................... 9
Set your system information ............................................................................... 9
IPv4 Settings ................................................................................................................ 10
Set your IPv4 settings ........................................................................................ 10
Administration ............................................................................................................. 11
Change administrator password ........................................................................ 11
Timeout........................................................................................................................ 12
Change web idle login timeout settings ............................................................ 12
SNMP ........................................................................................................................... 13
Global Settings ................................................................................................... 13
Community Table Settings ................................................................................. 14
Host Settings ...................................................................................................... 15
Statistics....................................................................................................................... 16
View Statistics .................................................................................................... 16
View Traffic Information Statistics..................................................................... 16
IEEE 802.3az EEE .......................................................................................................... 17
Enable IEEE 802.3az Power Saving Mode .......................................................... 17
Network ....................................................................................... 18
Physical Interface......................................................................................................... 18
Configure Physical Interfaces ............................................................................ 18
Spanning Tree .............................................................................................................. 20
Spanning Tree Global Settings ........................................................................... 20
Configure Spanning Tree Protocol port settings................................................ 21
Trunk ............................................................................................................................ 22
Configure port trunk settings (Trunk/Link Aggregation) ................................... 22
Mirroring ..................................................................................................................... 23
Configure port mirror settings ........................................................................... 23
Loopback Detection ..................................................................................................... 24
Enable loopback detection ................................................................................ 24
Static Unicast ............................................................................................................... 26
Add static unicast entries to the switch ............................................................ 26
Static Multicast ............................................................................................................ 27
Add static multicast entries to the switch ......................................................... 27
IGMP Snooping ............................................................................................................ 28
Configure IGMP Snooping Settings .................................................................... 28
Configure IGMP Snooping Group Settings ......................................................... 28
Bandwidth Control ...................................................................................................... 29
Configure Storm Control .................................................................................... 29
Set Ingress Rate Limiting.................................................................................... 30
Set Egress Rate Limiting ..................................................................................... 31
VLAN ............................................................................................................................ 32
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Table of Contents
ii
Add, modify, and remove VLANs ....................................................................... 32
Configure VLAN Port Settings ............................................................................ 33
Configure the VLAN forwarding Table ............................................................... 34
View the switch VLAN dynamic forwarding table .............................................. 35
Create a private VLAN ........................................................................................ 35
Voice VLAN .................................................................................................................. 37
Configuring Voice VLANs ................................................................................... 37
Create a Voice VLAN .......................................................................................... 38
Configure Voice VLAN OUI settings ................................................................... 39
QoS (Quality of Service .................................................................. 41
CoS ............................................................................................................................... 41
Set CoS priority settings ..................................................................................... 41
Port Priority ................................................................................................................. 42
Set Port Priority ................................................................................................. 42
DSCP ............................................................................................................................. 43
Set DSCP (Differentiated Services Code Point) Class Mapping settings ............ 43
Scheduling Algorithm ................................................................................................... 44
Set the Scheduling Algorithm ............................................................................ 44
PoE ............................................................................................... 45
Power over Ethernet.................................................................................................... 45
View PoE status ................................................................................................. 45
Configure PoE settings ....................................................................................... 46
Tools ............................................................................................. 47
Firmware Upgrade ....................................................................................................... 47
Upgrade your switch firmware .......................................................................... 47
Configuration ............................................................................................................... 48
Backup and Restore your switches configuration setting.................................. 48
Diagnostics ................................................................................................................... 49
Cable Diagnostics Test ....................................................................................... 49
Reboot ......................................................................................................................... 50
Reboot/Reset to Factory Defaults ..................................................................... 50
Using the Edge Smart Switch Management Utility ......................... 51
System Requirements .................................................................................................. 51
Installation ................................................................................................................... 51
Using the Utility ........................................................................................................... 52
Launching the Utility .......................................................................................... 52
Discovery List ..................................................................................................... 53
Monitor List ....................................................................................................... 53
Device Setting .................................................................................................... 54
Main Menu Options ........................................................................................... 55
Technical Specifications ................................................................ 56
Quick Installation GuideTroubleshooting ....................................... 58
Appendix ...................................................................................... 59
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
1
Product Overview
TPE-P521ES
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
5-Port Gigabit PoE+ Powered EdgeSmart Switch with PoE Pass Through, model TPE-
P521ES, is powered by a PoE+ switch or injector, no AC adapter is required. It features
two gigabit non-PoE ports, and two gigabit PoE ports to power devices such as IP
cameras, VoIP handsets, and wireless access points. Reducing unnecessary switch
complexity, this EdgeSmart switch is equipped with only the most commonly used
managed switch features. The simple web-based user interface allows you to easily
manage VLANs, QoS, and monitoring.
EdgeSmart Management
Provides an easy- to-use web-based management interface for reduced switch
configuration complexity and offers a combination of more commonly used SMB
management features for easy deployment.
Integration Flexibility
Managed features include access control lists, VLAN, IGMP Snooping, and QoS for
flexible network integration.
PoE+ Powered
No AC adapter requiredthis switch is powered by a PoE+ switch or injector, and
features two gigabit non-PoE ports, and two gigabit PoE ports to power devices such as
IP cameras.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
2
Ports
One gigabit PoE+ input port, two gigabit PoE output ports, and two gigabit ports
provides a 10Gbps switching capacity.
PoE Power
Two gigabit PoE pass through ports with an 18W total PoE power budget.
Compact Design
With a compact and lightweight housing design this switch is well-suited for desktop
installations. Its fanless design is ideal for quiet environments that require silent
operation.
Network Management
A broad range of network configurations are supported by: 802.3ad link aggregation,
802.1Q VLAN, bandwidth controls, IGMP, loopback detection, port mirroring, STP, RTSP
and 802.1p (QoS).
Troubleshooting
Traffic statistics and a convenient cable diagnostic test aid in network troubleshooting.
Housing
Compact wall mountable metal housing.
LED Indicators
LED indicators convey port status.
Product Hardware Features
Front View
Rear View
Reset Button Press and hold the button 1~5 seconds and release to
reboot the device. Pressing the button more than 6 seconds will reset
the switch to factory defaults. The ports LEDs will display Amber and
then turn off to indicate that the reset was initiated.
Gigabit Ethernet PoE Out Ports (1-2) Connect either network PoE or
non-PoE devices.
Gigabit Ethernet Ports (3-4) Connect non-PoE network devices.
Gigabit Ethernet PoE+ in Ports (5) Must be connected to a PoE or PoE+
power source in order to power this switch.
Reset Button
Gigabit Ports
Gigabit PoE
out Ports
Gigabit PoE/PoE+ in
Port
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
3
LED Indicators
Switch Installation
Desktop Hardware Installation
The site where you install the switch may greatly affect its performance. When
installing, consider the following pointers:
Note: Your switch model may be different than the one shown in the example
illustrations.
Install the Switch in a fairly cool and dry place.
Install the Switch in a site free from strong electromagnetic field generators (such
as motors), vibration, dust, and direct exposure to sunlight.
Leave some space on the sides of the switch for ventilation.
Install the Switch on a sturdy, level surface that can support its weight, or in an
EIA standard-size equipment rack. For information on rack installation, see the
next section, Rack Mounting.
When installing the Switch on a level surface, attach the rubber feet to the
bottom of each device. The rubber feet cushion the hub and protect the hub
case from scratching.
LED
State
POWER
(Green)
ON
OFF
Ports 1-5
Right LED
(Link/Act)
GREEN
AMBER
BLINKING
OFF
Ports 1-2
Left LED
(PoE Status)
GREEN
AMBER
OFF
Port 5
Left LED
(PoE-in Status)
GREEN
AMBER
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
4
Basic IP Configuration
3. Assign a static IP address to your computer’s network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
4. Open your web browser, and type the IP address of the switch in the address bar, and
then press Enter. The default IP address is 192.168.10.200.
5. Enter the User Name and Password, and then click Login. By default:
User Name: admin
Password: admin
Note: User name and password are case sensitive.
6. Click System and then click IPv4 Setup.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
5
7. Configure the switch IP address settings to be within your network subnet, then click
Apply.
Note: You may need to modify the static IP address settings of your computer’s network
adapter to IP address settings within your subnet in order to regain access to the switch.
8. When confirmation message appears click OK.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
6
TRENDnet User’s Guide
TPE-P521ES
Connect additional devices to your switch
You can connect additional computers or other network devices to your switch using Ethernet cables to connect them to one of the available Gigabit Ports (1-4). Check the status of the
LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device.
Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network
settings (also called TCP/IP settings) are configured properly within the network subnet your switch is connected.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
7
Accessing switch management interfaces
Access your switch web management page
Note: Your switch default management IP address http://192.168.10.200 is accessed
through the use of your Internet web browser (e.g. Internet Explorer®, Firefox®,
Chrome, Safar, Opera™) and will be referenced frequently in this User’s Guide.
Throughout this user’s guide, the term Web Configuration will be used to reference
access from web management page.
1. Open your web browser and go to the IP address http://192.168.10.200. Your switch
will prompt you for a user name and password.
2. Enter the user name and password. By default:
User Name: admin
Password: admin
Note: User Name and Password are case sensitive.
System Info
View your switch status information
Switch Info
You may want to check the general system information of your switch such as firmware
version, boot loader information and system uptime. Other information includes
administration information, and System MAC Address IPv4 information.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on Switch Info.
Switch Information
System Up For The duration your switch has been running continuously without
a restart/power cycle (hard or soft reboot) or reset.
Runtime Image: The current software or firmware version your switch is running.
Boot Loader The current boot loader version your switch is running.
Administration Information
System Name Displays the identifying system name of your switch. This
information can be modified under the System section.
System Location - Displays the identifying system location of your switch. This
information can be modified under the System section.
System Contact Displays the identifying system contact or system administrator
of your switch. This information can be modified under the System section.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
8
System MAC Address, IPv4 Information
MAC Address: Displays the switch system MAC address.
IP Address Displays the current IPv4 address assigned to your switch.
Subnet Mask Displays the current IPv4 subnet mask assigned to your switch.
Default Gateway Displays the current gateway address assigned to your switch.
Automatic Network Features
IPv4 DHCP Client Mode: Displays if your switch IPv4 address setting is set to
DHCP client.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
9
System
System Management
Set your system information
System > System Management
This section explains how to assign a name, location, and contact information for the
switch. This information helps in identifying each specific switch among other switches
in the same local area network. Entering this information is optional.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, and click on System Management.
3. Review the settings. When you have completed making changes, click Apply to save
the settings.
System Name - Specifies a name for the switch, the name is optional and may
contain up to 15 characters.
System Location - Specifies the location of the switch. The location is optional
and may contain up to 30 characters.
System Contact - Specifies the name of the network administrator responsible
for managing the switch. This contact name is optional and may contain up to
30 characters.
4. Click Apply.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
10
IPv4 Settings
Set your IPv4 settings
System > IPv4 Setup
This section allows you to change your switch IPv4 address settings. Typically, the IP
address settings should be changed to match your existing network subnet in order to
access the switch management page on your network.
Default Switch IPv4 Address: 192.168.10.200
Default Switch IPv4 Subnet Mask: 255.255.255.0
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, and click on IPv4 Setup.
3. Review the settings. When you have completed making changes, click Apply to save
the settings.
System MAC Address: Displays the switch MAC address information.
System IP Address: Enter the new switch IP address. (e.g. 192.168.200.200)
System Subnet Mask: Enter the new switch subnet mask. (e.g. 255.255.255.0)
System Default Gateway: Enter the default gateway IP address. (e.g.
192.168.200.1 or typically your router/gateway to the Internet).
System IP Mode: Click the drop-down list and select Static to manually specify
your IP address settings or DHCP to allow your switch to obtain IP address
settings automatically from a DHCP server on your network.
4. Click Apply.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
11
Administration
Change administrator password
System > Administration
This section explains how to change the administrator password for access to the switch
management page.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, and click on Administration.
3. Review the settings.
4. Click Apply.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
12
Timeout
Change web idle login timeout settings
System > Timeout
This section explains how to modify the switch management page idle timeout settings.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, and click on Timeout.
3. Review the settings. Click Apply to save changes.
Web Idle Timeout - Enter the idle period in minutes, when the switch will
automatically log out a user from the switch management page.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
13
SNMP
Global Settings
System > SNMP > Global Settings
You can manage a switch by viewing and configuring the management information base
(MIB) objects on the device with the Simple Network Management Program (SNMP).
This chapter describes how to configure SNMP. A Group Name, IP address of the switch
and at least one community string is the minimum required to manage the switch using
SNMP.
Note: If you disable the SNMP on the switch, the switch will not be manageable via
SNMP using MIBs.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, click on SNMP, and click on Global Settings.
3. Review the settings. Click Apply to save changes.
SNMP Global Settings: Click the drop-down list to one of the following options.
o Enabled - When you enable this parameter, SNMP is active. You can
manage the switch with SNMP network management software and
the switch’s private MIB.
o Disabled - When you select this parameter, SNMP is inactive.
Trap Settings: Enable this setting to enable output to a SNMP Trap Host for the
following toggle-able conditions:
o SNMP Authentication Trap When a client connects to the switch
with SNMP
o Port Link Up When any port on the switch goes from an inactive
state to active.
o Port Link Down When any active port on the switch becomes
inactive.
o ColdStart When the switch is powered on by connecting to a power
source.
o WarmStart When the switch is reboot from a management
interface.
4. Click Apply.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
14
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
Community Table Settings
System > SNMP > Community Table Settings
A community string has attributes for controlling who can use the string and what the
string will allow a network management station to do on the switch. The Web
Management Utility does not provide any default community strings. You must first
define an SNMP User and Group Name on the SNMP User/Group page and then define a
Community Name on the SNMP Community Table page.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, click on SNMP, and click on Community Table Settings.
3. Review the settings.
Editing SNMP Community Settings
Select an Access Right either Read Write or Read Only.
Enter a Community Name (View Policy). If you change the default name on
this page, you must also update the Host Settings to match the community
name.
Note: Host Settings page. If you change a name on the Community Table
Settings page, you must also change the name on the Host Settings page or
else the Community entry is displayed, but the agent/manager communication
fails.
Click Apply. The values of the new Community Name and its respective access
rights are displayed.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
15
2. Click Continue to return to the Web Configuration of your switch.
Host Settings
System > SNMP > Host Settings
A Host IP address is used to specify a management device that needs to receive SNMP
traps sent by the switch. This IP address is associated with the SNMP Version and a valid
Community Name in the Host table of the switch.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, click on SNMP, and click on Host Settings.
3. Review the settings.
Enter the Host IPv4 Address for the management device that is to receive the
SNMP traps.
Select the SNMP Version, either v1 or v2c, that is configured for the host
management device.
Enter a Community String (Community Name) that you have defined
previously in the SNMP Community table. The Community String must
correlate with one of the communities displayed on the SNMP Community
Table page. If you enter a Community String that has not been pre-defined, the
Trap Host entry is displayed, but agent/manager communication fails.
Click Apply. The new host is added to the table.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
16
Statistics
View Statistics
System > Statistics
Statistics provide important information for troubleshooting switch problems at the port
level. The Web Management Utility provides a two statistics charts, including Traffic
Information and Error Information.
View Traffic Information Statistics
System > Statistics > Traffic
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System, click on Statistics.
3. View the Traffic Information Statistics.
TxOK: Transmit OK, number of frames sent from the switch through the specified
port number.
TxErr: Transmit Error, number of frames that failed to be sent from the switch
through the specified port number
RxOK: Receive OK, number of frames received by the switch through the
specified port number.
RxErr: Receive Error, number of frames that were failed to be received by the
switch through the specified port number.
Clear: Clicking Apply will clear the Statistic Information of that row (port
number).
Refresh: Clicking Refresh will refresh the data on the page.
© Copyright 2018 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-P521ES
17
IEEE 802.3az EEE
Enable IEEE 802.3az Power Saving Mode
System > IEEE 802.3az EEE
The IEEE 802.3 EEE standard defines mechanisms and protocols intended to reduce the
energy consumption of network links during periods of low utilization, by transitioning
interfaces into a low-power state without interrupting the network connection. The
transmitted and received sides should be IEEE802.3az EEE compliance. By default, the
switch disabled the IEEE 802.3az EEE function. Users can enable this feature via the
IEEE802.3az EEE setting page.
1. Log into your switch management page (see “Access your switch management page
on page 7).
2. Click on System and click on IEEE 802.3az EEE.
3. Click the IEEE 802.3az EEE Status drop-down list and select Enabled to enable the
power saving feature and click Apply to save the settings.
NOTE: The configured settings are only applied to the switch’s temporary memory and
will be lost upon the next power-cycle. Please follow these next steps to save the
configurations to the switch’s NV-RAM to ensure the settings will remain throughout
power-cycles and reboots:
1. From the menu on the left: click on Save, then click the blue button Save
Settings to Flash.
2. Click Continue to return to the Web Configuration of your switch.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Trendnet RB-TPE-P521ES User guide

Category
Network switches
Type
User guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI