Trendnet TPE-TG82ES User manual

Trendnet
Brand
Trendnet
Model
TPE-TG82ES
Category
Network switches
Type
User manual

This manual is also suitable for


TRENDnetUser’sGuide
CoverPage

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TableofContents
i
Contents
ProductOverview.............................................................................1
PackageContents..........................................................................................................1
Features.........................................................................................................................1
ProductHardwareFeatures...........................................................................................2
BasicInstallation..............................................................................3
Connectadditionaldevicestoyourswitch....................................................................5
Configureyourswitch.......................................................................6
Accessyourswitchmanagementpage..........................................................................6
SwitchInfo.....................................................................................................................6
Viewyourswitchstatusinformation...................................................................6
System...........................................................................................................................8
Setyoursysteminformation...............................................................................8
SetyourIPv4settings..........................................................................................9
Changeadministratorpasswordandaddaccounts...........................................10
ChangeWebidlelogintimeoutsettings............................................................11
EnableorDisableSNMP....................................................................................11
SettheSNMPCommunitySettings....................................................................12
ConfiguretheSNMPTrapManagement............................................................13
ViewStatistics....................................................................................................14
ViewTrafficInformationStatistics.....................................................................14
EnableIEEE802.3azPowerSavingMode..........................................................14
Network.......................................................................................................................15
ConfigurePhysicalInterfaces.............................................................................15
ConfigureSpanningTree(STP,RSTP).................................................................16
ConfigureSpanningTreeProtocolportsettings................................................17
Configureporttrunksettings(Trunk/LinkAggregation)...................................18
Configureportmirrorsettings...........................................................................19
Enableloopbackdetection................................................................................20
Addstaticunicastentriestotheswitch.............................................................21
Addstaticmulticastentriestotheswitch.........................................................22
ConfigureIGMPSnoopingSettings....................................................................23
ConfigureIGMPSnoopingGroupSettings.........................................................23
ConfigureStormControl....................................................................................24
SetIngressRateLimiting....................................................................................24
SetEgressRateLimiting.....................................................................................25
Add,modify,andremoveVLANs.......................................................................25
ConfigureVLANPortSettings............................................................................27
ConfiguretheVLANforwardingTable...............................................................27
ViewtheswitchVLANDynamicforwardingtable.............................................28
CreateaprivateVLAN........................................................................................28
ConfiguringVoiceVLANs...................................................................................30
CreateaVoiceVLAN..........................................................................................31
ConfigureVoiceVLANOUIsettings...................................................................31
QoS(QualityofService)...............................................................................................33
SetCoSprioritysettings.....................................................................................33
SetPortPriority.................................................................................................33
SetDSCP(DifferentiatedServicesCodePoint)ClassMappingsettings............34
SettheSchedulingAlgorithm............................................................................34
PoEConfiguration........................................................................................................36
ConfigurePoEsettings.......................................................................................37
ConfigurePoEsettings.......................................................................................37
SwitchMaintenance......................................................................39
Upgradeyourswitchfirmware....................................................................................39
FirmwareUpgradeviaHTTPSettings................................................................39
Backupandrestoreyourswitchconfigurationsettings..............................................40
Backup/RestoreviaHTTPSettings.....................................................................40
CableDiagnosticsTest.................................................................................................40
Reboot/Resettofactorydefaults................................................................................41
UsingtheEdgeSmartSwitchManagementUtility..........................42
SystemRequirements..................................................................................................42
Installation...................................................................................................................42
UsingtheUtility...........................................................................................................44
LaunchingtheUtility..........................................................................................44

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TableofContents
ii
DiscoveryList.....................................................................................................45
MonitorList.......................................................................................................45
DeviceSetting....................................................................................................46
MainMenuOptions...........................................................................................47
TechnicalSpecifications..................................................................48
Troubleshooting.............................................................................50
Appendix........................................................................................51

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
1
ProductOverview
TPE‐TG82ES
PackageContents
Inadditiontoyourswitch,thepackageincludes:
QuickInstallationGuide
Poweradapter(54VDC,1.67A)
Ifanypackagecontentsaremissingordamaged,pleasecontacttheretailstore,online
retailer,orreseller/distributorfromwhichtheproductwaspurchased.
Features
TRENDnet’s8‐PortGigabitEdgeSmartPoE+Switch,modelTPE‐TG82ES,isacost‐
effectivedesktopPoEmanagedswitchsolutionforhigh‐speedgigabitPoE+applications.
ThisEdgeSmartswitchfeaturesthemostcommonlyusedmanagedswitchfeatures,
reducingunnecessaryswitchcomplexity.Theweb‐basedmanagementinterfaceoffers
featuresfortrafficcontrol,LACP,RSTP,VLAN,QoS,andmonitoring.TRENDnet’sTPE‐
TG82ESdesktopPoEmanagedswitchprovideseightgigabitPoE+portsforconnecting
devicessuchaswirelessaccesspoints,IPcameras,andVoIPhandsets.
Ports
EightgigabitPoE+portsprovidea16Gbpsswitchingcapacity
CompactDesign
Withacompactandlightweightmetalhousingdesign,thisdesktopPoEmanagedswitch
isalsowell‐suitedforwallmountinstallations
NetworkManagement
Theweb‐basedmanagementinterfaceoffersfeaturesforloopbackdetection,RSTP,
LACP,VLAN,IGMPSnooping,andQoS
Monitoring
SNMP,SNMPTrap,andPortMirroringsupportadministratormonitoringsolutions
Troubleshooting
Trafficstatisticsandaconvenientcablediagnostictest
Fanless
DesktopPoEmanagedswitchwithfanlessdesignisidealforquietenvironmentsthat
requiresilentoperation

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
2
ProductHardwareFeatures
FrontView
RearView
ResetButton–Pressandholdthebutton1~5secondsandreleaseto
rebootthedevice.Pressingthebuttonmorethan6secondswillreset
theswitchtofactorydefaults.TheportsLEDswilldisplayAmberand
thenturnofftoindicatethattheresetwasinitiated.
GigabitEthernetPoE+Ports(1‐8)–ConnecteithernetworkPoE+or
non‐PoEdevices.
LEDIndicators
ThedesktopPoEmanagedswitchincludesLEDindicatorsthatconveyportstatus
DiagnosticLEDs
PowerLED
On WhenthePowerLEDison,thedeviceisreceivingpower.
Off
WhenthePowerLEDisoff,thepoweradapterisnot
connectedorthedeviceisnotreceivingpower.
PoEMAX(PoweroverEthernetMax.)
On
WhenreachingnearthemaxPoEpowerbudgetprovided
64Worabove,theLEDwillturnonandthesystemwillnot
providepoweradditionalPD(PoEclientdevices)aftermax
PoEbudgetisreached.
Off
WhenthePoEpowerprovidedisbelowthe57WPoE
powerbudget.
ResetButton
GigabitPoE+Ports
ACPowerPort

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
3
GigabitEthernetPoE+PortLEDs(1‐8)
Link/ActivitybuttonMode

TopRight
LED
Green
on:
WhentheGreenLEDison,therespectiveport
isconnectedtoa1GbpsEthernetnetwork.
Amber
on:
WhentheAmberLEDlightson,therespective
port is connected to a 10/100Mbps Ethernet
network.
Green
Blinking:
WhentheLEDisblinkinggreen,theportis
transmittingorreceivingdataonthenetwork
at1Gbpsspeed.
Amber
Blinking:
WhentheLEDisblinkingamber,theportis
transmittingorreceivingdataonthenetwork
at10/100Mbpsspeed.
Off WhentheLEDisoff,therespectiveportis
disconnected.
GigabitEthernetPortPoE+LEDs(1‐8)
PoELEDbuttonMode

TopLeft
LED
Green
on:
WhentheGreenLEDison,theconnected
deviceisreceivingpower.
Amber
on:
WhentheAmberLEDlightson,theconnected
PoEdeviceisnotreceivingpower.Thecauseis
either insufficient power budget, or due to
Class/PowerLimit restrictions in the PoE
configurations.
Off:
WhentheLEDisoff,therespectiveportis
either not connected to a PoE device or is
disconnected.
BasicInstallation
3.AssignastaticIPaddresstoyourcomputer’snetworkadapterinthesubnetof
192.168.10.x(e.g.192.168.10.25)andasubnetmaskof255.255.255.0.
4.Openyourwebbrowser,andtypetheIPaddressoftheswitchintheaddressbar,and
thenpressEnter.ThedefaultIPaddressis192.168.10.200.
5.EntertheUserNameandPassword,andthenclickLogin.Bydefault:
UserName:admin
Password:admin
Note:Usernameandpasswordarecasesensitive.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
4
6.ClickSystemandthenclickIPv4Setup.
7.ConfiguretheswitchIPaddresssettingstobewithinyournetworksubnet,thenclick
Apply.
Note:YoumayneedtomodifythestaticIPaddresssettingsofyourcomputer’snetwork
adaptertoIPaddresssettingswithinyoursubnetinordertoregainaccesstotheswitch.
5.Inthelefthandpanel,clickonSave
6.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
5
TRENDnetUser’sGuide
TPE‐TG82ES
Connectadditionaldevicestoyourswitch
YoucanconnectcomputersorothernetworkdevicestoyourswitchusingEthernetcablestoconnectthemtooneoftheavailableGigabitEthernetPoE+Ports(1‐8).Checkthestatusof
theLEDindicatorsonthefrontpanelofyourswitchtoensurethephysicalcableconnectionfromyourcomputerordevice.YoucanusetheGigabitEthernetportsasnetworkuplinks.
Note:Ifyouencounterissuesconnectingtoyournetwork,theremaybeaproblemwithyourcomputerordevicenetworksettings.Pleaseensurethatyourcomputerordevicenetwork
settings(alsocalledTCP/IPsettings)areconfiguredproperlywithinthenetworksubnetyourswitchisconnected.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
6
Configureyourswitch
Accessyourswitchmanagementpage
Note:YourswitchdefaultmanagementIPaddresshttp://192.168.10.200isaccessed
throughtheuseofyourInternetwebbrowser(e.g.InternetExplorer®,Firefox®,
Chrome™,Safari®,Opera™)andwillbereferencedfrequentlyinthisUser’sGuide.
1.OpenyourwebbrowserandgototheIPaddresshttp://192.168.10.200.Yourswitch
willpromptyouforausernameandpassword.
2.Entertheusernameandpassword.Bydefault:
UserName:admin
Password:admin
Note:UserNameandPasswordarecasesensitive.
SwitchInfo
Viewyourswitchstatusinformation
SwitchInfo
Youmaywanttocheckthegeneralsysteminformationofyourswitchsuchasfirmware
version,bootloaderinformationandsystemuptime.Otherinformationincludes
administrationinformation,SystemMACAddress,IPv4InformationandAutomatic
NetworkFeaturesinformation.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystemInfo.
SystemInformation
SystemUpFor–Thedurationyourswitchhasbeenrunningcontinuouslywithout
arestart/powercycle(hardorsoftreboot)orreset.
RuntimeImage:Thecurrentsoftwareorfirmwareversionyourswitchisrunning.
BootLoader–Thecurrentbootloaderversionyourswitchisrunning.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
7
AdministrationInformation
SystemName–Displaystheidentifyingsystemnameofyourswitch.This
informationcanbemodifiedundertheSystemsection.
SystemLocation‐Displaystheidentifyingsystemlocationofyourswitch.This
informationcanbemodifiedundertheSystemsection.
SystemContact–Displaystheidentifyingsystemcontactorsystemadministrator
ofyourswitch.ThisinformationcanbemodifiedundertheSystemsection.
SystemMACAddress,IPv4Information
MACAddress:DisplaystheswitchsystemMACaddress.
IPAddress–DisplaysthecurrentIPv4addressassignedtoyourswitch.
SubnetMask–DisplaysthecurrentIPv4subnetmaskassignedtoyourswitch.
DefaultGateway–Displaysthecurrentgatewayaddressassignedtoyourswitch.
AutomaticNetworkFeatures
IPv4DHCPClientMode:DisplaysifyourswitchIPv4addresssettingissetto
DHCPclient.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
8
System
Setyoursysteminformation
System>SystemManagement
Thissectionexplainshowtoassignaname,location,andcontactinformationforthe
switch.Thisinformationhelpsinidentifyingeachspecificswitchamongotherswitches
inthesamelocalareanetwork.Enteringthisinformationisoptional.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,andclickonSystemManagement.
3.Reviewthesettings.Whenyouhavecompletedmakingchanges,clickApplytosave
thesettings.
SystemName‐Specifiesanamefortheswitch,thenameisoptionalandmay
containupto15characters.
SystemLocation‐Specifiesthelocationoftheswitch.Thelocationisoptional
andmaycontainupto30characters.
SystemContact‐Specifiesthenameofthenetworkadministratorresponsible
formanagingtheswitch.Thiscontactnameisoptionalandmaycontainupto
30characters.
4.ClickApply.
5.Inthelefthandpanel,clickonSave
6.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
9
SetyourIPv4settings
System>IPv4Setup
ThissectionallowsyoutochangeyourswitchIPv4addresssettings.Typically,theIP
addresssettingsshouldbechangedtomatchyourexistingnetworksubnetinorderto
accesstheswitchmanagementpageonyournetwork.
DefaultSwitchIPv4Address:192.168.10.200
DefaultSwitchIPv4SubnetMask:255.255.255.0
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,andclickonIPv4Setup.
3.Reviewthesettings.Whenyouhavecompletedmakingchanges,clickApplytosave
thesettings.
SystemMACAddress:DisplaystheswitchMACaddressinformation.
SystemIPAddress:EnterthenewswitchIPaddress.(e.g.192.168.200.200)
SystemSubnetMask:Enterthenewswitchsubnetmask.(e.g.255.255.255.0)
SystemDefaultGateway:EnterthedefaultgatewayIPaddress.(e.g.
192.168.200.1ortypicallyyourrouter/gatewaytotheInternet).
SystemIPMode:Clickthedrop‐downlistandselectStatictomanuallyspecify
yourIPaddresssettingsorDHCPtoallowyourswitchtoobtainIPaddress
settingsautomaticallyfromaDHCPserveronyournetwork.
DHCPRetryTime:Enterthenumberofsecondsyourdevicewillretrytoconnect
toaDHCPserver.
4.ClickApply.
5.Inthelefthandpanel,clickonSave
6.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
10
Changeadministratorpasswordandaddaccounts
System>Administration
Thissectionexplainshowtochangetheadministratorpasswordcreateadditional
administrativeuseraccountsforaccesstotheswitchmanagementpage.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,andclickonAdministration.
3.Reviewthesettings.
InthePasswordfield,enterthenewpasswordandenterthenewpasswordagainthe
ConfirmPasswordfieldtoverify.Then,clickApply.
Note:Thepasswordconsistsofupto12alphanumericcharacters.
Tocreateadditionaladministrativeuseraccounts:
OldPassword:Entertheoldpassword
NewPassword:Enterthenewpasswordyouwishtochangeitto
ConfirmPassword:Enterthepasswordagaintoconfirmthechange
Note:Thepasswordconsistsofupto12alphanumericcharacters.

4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.


©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
11
ChangeWebidlelogintimeoutsettings
System>Timeout
Thissectionexplainshowtomodifytheswitchmanagementpageidletimeoutsettings.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,andclickonTimeout.
3.Reviewthesettings.ClickApplytosavechanges.
WebIdleTimeout‐Entertheidleperiodinminutes,whentheswitchwill
automaticallylogoutauserfromtheswitchmanagementpage.
4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.
EnableorDisableSNMP
System>SNMP>GlobalSettings
Youcanmanageaswitchbyviewingandconfiguringthemanagementinformationbase
(MIB)objectsonthedevicewiththeSimpleNetworkManagementProgram(SNMP).
ThischapterdescribeshowtoconfigureSNMP.AGroupName,IPaddressoftheswitch
andatleastonecommunitystringistheminimumrequiredtomanagetheswitchusing
SNMP.
Note:IfyoudisabletheSNMPontheswitch,theswitchwillnotbemanageablevia
SNMPusingMIBs.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,clickonSNMP,andclickonGlobalSettings.
3.Reviewthesettings.ClickApplytosavechanges.
SNMPGlobalState:Clickthedrop‐downlisttooneofthefollowingoptions.
o Enabled‐Whenyouenablethisparameter,theSNMPagentisactive.
YoucanmanagetheswitchwithSNMPnetworkmanagement
softwareandtheswitch’sprivateMIB.
o Disabled‐Whenyouenablethisparameter,theSNMPagentis
inactive.
SNMPTrapGlobalState:SelectEnabledfromthedropdownmenu
o SNMPAuthenticationTrap:EnablethistoturnonSNMPtrapforyour
network
o PortLinkUp:EnablethistoturnonSNMPtrapsettingsforuplink
ports
o PortLinkDown:EnablethistoturnonSNMPtrapsettingsfor
downlinkports
o ColdStart:EnablethistoturnonSNMPColdStartfunctionforswitch
powerrebootalert.
o WarmStart:EnablethistoturnonSNMPWarmStartfunctionfor
switchsoftwarereboot.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
12
4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.
SettheSNMPCommunitySettings
System>SNMP>CommunityTableSettings
TheSNMPCommunityTableSettingsscreenallowsnetworkmanagerstodefinethe
SNMPCommunityNameandtheaccessright
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,clickonSNMP,andclickonCommunityTableSettings..
3.Reviewthesettings.ClickApplytosavethesettings.
AccessRight:Assignusersthelevelofaccessfromthedropdownmenu
CommunityNsme:InputthenameofthisSNMPcommunity.
4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
13
ConfiguretheSNMPTrapManagement
System>SNMP>HostSettings
AHostIPaddressisusedtospecifyamanagementdevicethatneedstoreceiveSNMP
trapssentbytheswitch.ThisIPaddressisassociatedwiththeSNMPVersionandavalid
CommunityNameintheHosttableoftheswitch.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,clickonSNMP,andclickonHostSettings.
3.Reviewthesettings.
CreateTrapHostTableEntry
UsethefollowingproceduretocreateatrapHosttableentry:
EntertheHostIPAddressforthemanagementdevicethatistoreceivethe
SNMPtraps.
SelecttheSNMPVersion,eitherv1orv2c,thatisconfiguredforthehost
managementdevice.
EnteraCommunityNamethatyouhavedefinedpreviouslyintheSNMP
Communitytable.TheCommunityNamemustcorrelatewithoneofthe
communitiesdisplayedontheSNMPCommunityTablepage.Ifyouentera
CommunityNamethathasnotbeenpre‐defined,theTrapHostentryis
displayed,butagent/managercommunicationfails.
4.ClickApply.Thenewhostisaddedtothetable.
5.Inthelefthandpanel,clickonSave
6.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
14
ViewStatistics
System>Statistics
Statisticsprovideimportantinformationfortroubleshootingswitchproblemsattheport
level.ThestatisticstrafficinformationsupportnormalpacketsandErrorpackets
information.
ViewTrafficInformationStatistics
System>Statistics>Traffic
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonSystem,clickonStatistics,andclickonTraffic.
3.ViewtheTrafficInformationStatistics.
PortID:Theportnumberwheretheinformationisbeingdisplayed.
TxOK:Outboundtraffic(Packets/s),numberofoutboundbytespersecond
TxErr:Outboundtraffic(Packets/s),numberoferroroutboundbytespersecond
RxOK:Inboundtraffic(Packets/s),numberofoutboundbytespersecond
RxErr:Inboundtraffic(Packets/s),numberoferroroutboundbytespersecond
Clear:ClicktheApplybuttontoclearportspecificTrafficinformation.
Refresh: Click the Refresh button to update table with newest traffic
information.
EnableIEEE802.3azPowerSavingMode
System>IEEE802.3azEEE
TheIEEE802.3EEEstandarddefinesmechanismsandprotocolsintendedtoreducethe
energyconsumptionofnetworklinksduringperiodsoflowutilization,bytransitioning
interfacesintoalow‐powerstatewithoutinterruptingthenetworkconnection.The
transmittedandreceivedsidesshouldbeIEEE802.3azEEEcompliance.Bydefault,the
switchdisabledtheIEEE802.3azEEEfunction.Userscanenablethisfeatureviathe
IEEE802.3azEEEsettingpage.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonToolsandclickonIEEE802.3azEEE.
3.ClicktheIEEE802.3azEEEStatusdrop‐downlistandselectEnabledtoenablethe
powersavingfeatureandclickApplytosavethesettings.
4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
15
Network
ConfigurePhysicalInterfaces
Network>PhysicalInterface
Thissectionallowsyoutoconfigurethephysicalportparameterssuchasspeed,duplex,
andflowcontrol.Thissectionalsoreportsthecurrentlinkstatusofeachportand
negotiatedspeed/duplex.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonNetworkandclickonPhysicalInterface.
3.Reviewthesettings.ClickApplytosavechanges.
Port‐Specifiestheportnumber.TheAllvalueindicatesports1through10on
theSwitch.Youcannotchangethisparameter.YoucanusetheAllrowvaluein
thePortcolumntoapplyAdminStatus,Mode,Jumbo,FlowContrl,EAP,BPDU
settingstoallportsatthesametime.
LinkStatus‐Thisparameterindicatesthestatusofthelinkbetweentheport
andtheendnodeconnectedtotheport.Thepossiblevaluesare:
o Up‐Thisparameterindicatesavalidlinkexistsbetweentheportand
theendnode.
o Down‐Thisparameterindicatestheportandtheendnodehavenot
establishedavalidlink.
Admin.Status:Thisparameterindicatestheoperatingstatusoftheport.You
canusethisparametertoenableordisableaport.Youmaywanttodisablea
portandpreventpacketsfrombeingforwardedifaproblemoccurswiththe
nodeorcableconnectedtotheport.Youcanenabletheporttoresume
normaloperationaftertheproblemhasbeenfixed.Youcanalsodisablean
unusedporttosecureitfromunauthorizedconnections.Thepossiblevalues
are:
o Enabled‐Thisparameterindicatestheportisabletosendandreceive
Ethernetframes.
o Disabled‐Thisparameterindicatestheportisnotabletosendand
receiveEthernetframes.
Mode:Thisparameterindicatesthespeedandduplexmodesettingsforthe
port.Youcanusethisparametertosetthespeedandduplexmodeofaport.
Thepossiblesettingsare:
o Auto‐ThisparameterindicatestheportisusingAuto‐Negotiationto
settheoperatingspeedandduplexmode.Theactualoperatingspeed
andduplexmodeoftheportaredisplayedinparentheses(for
example,“1000/F”for1000Mbpsfullduplexmode)afteraport
establishesalinkwithanendnode.
o 1000/Full‐Thisparameterindicatestheportisconfiguredfor
1000Mbpsoperationinfull‐duplexmode.
o
100/Full‐Thisparameterindicatestheportisconfiguredfor100Mbps
operationinfull‐duplexmode.
o 10/Full‐Thisparameterindicatestheportisconfiguredfor10Mbps
operationinfull‐duplexmode.
o 100/Half‐Thisparameterindicatestheportisconfiguredfor100Mbps
operationinhalf‐duplexmode.
o 10/Half‐Thisparameterindicatestheportisconfiguredfor10Mbps
operationinhalf‐duplexmode.
Note:WhenselectingaModesetting,thefollowingpointsapply:
o Whenatwisted‐pairportissettoAuto‐Negotiation,theendnodeshould
alsobesettoAuto‐Negotiationtopreventaduplexmodemismatch.
o AswitchportusingAuto‐Negotiationdefaultstohalf‐duplexifitdetects
thattheendnodeisnotusingAuto‐Negotiation.Thiscanresultina
mismatchiftheendnodeisoperatingatafixedduplexmodeoffull‐duplex.
Toavoidthisproblemwhenconnectinganendnodewithafixedduplex
modeoffull‐duplextoaswitchport,disableAuto‐Negotiationontheport
andsettheport’sspeedandduplexmodemanually..
FlowCtrl:FlowControl,Thisparameterreflectsthecurrentflowcontrolsetting
ontheport.Theswitchusesaspecialpausepackettonotifytheendnodeto
stoptransmittingforaspecifiedperiodoftime.Thepossiblevaluesare:

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
16
o Ignore‐ThisparameterindicatesthattheAllsettingdoesnotapplyto
theFlowControlfield.Inotherwords,eachportissetindividually.
o Enabled‐Thisparameterindicatesthattheportispermittedtouse
flowcontrol.
o Disabled‐Thisparameterindicatesthattheportisnotpermittedto
useflowcontrol.

5.Inthelefthandpanel,clickonSave
6.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.
ConfigureSpanningTree(STP,RSTP)
Network>SpanningTree>Protocol
SpanningTreeProtocol(STP)providesnetworktopologyforanyarrangementof
bridges/switches.STPalsoprovidesasinglepathbetweenendstationsonanetwork,
eliminatingloops.Loopsoccurwhenalternateroutesexistbetweenhosts.Loopsinan
extendednetworkcancausebridgestoforwardtrafficindefinitely,resultingin
increasedtrafficandreducingnetworkefficiency.
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonNetwork,clickonSpanningTree,andclickonProtocol.
3.Reviewthesettings.ClickApplytosavechanges.
SpanningTreeState:SelecttheSTPstateonthedevice.Thepossiblefield
valuesare:
o Disable–DisablesSTPonthedevice.Thisisthedefaultvalue.
o Enable–EnablesSTPonthedevice.
SpanningTreeMode:SpecifiestheSpanningTreeProtocol(STP)modeto
enableontheswitch.Thepossiblefieldvaluesare:
o STP–EnablesSTP802.1donthedevice.
o RSTP–EnablesRapidSTP802.1wonthedevice.Thisisthedefault
value.
STPNewRootTraps:SelecttheSTPRootTraponthedevice.Thepossiblefield
valuesare:
o Disable–DisablesSTPRootTraponthedevice.Thisisthedefault
value.
o Enable–EnablesSTPRootTraponthedevice.
STPTopologyChange:SelecttheSTPTopologyChangeonthedevice.The
possiblefieldvaluesare:
o Disable–DisablesSTPTopologyChangeonthedevice.Thisisthe
defaultvalue.
o Enable–EnablesSTPTopologyChangeonthedevice.

©Copyright2018TRENDnet.AllRightsReserved.
TRENDnetUser’sGuide
TPE‐TG82ES
17
Inaddition,thissectionalsodisplaysthespanningtreerootinformation.
ConfigureSpanningTreeProtocolportsettings
Network>SpanningTree>RSTPPortSettings
1.Logintoyourswitchmanagementpage(see“Accessyourswitchmanagementpage”
onpage6).
2.ClickonNetwork,clickonSpanningTree,andclickonRSTPPortSettings.
3.Reviewthesettings.Foreachentry,clickApplytosavechanges.
Port:Indicatestheportnumber(1‐8)
PortFast:Selectthespanningtreeprotocolforeachport
o Network:Automaticallyletsthedevicedeterminethetypeofdevice
thatisconnectedtotheport
o Disable:Disableportfastonaparticularport.
o Edge:IndicatesthatthisportisconnectedtoanEdgedevice.
4.Inthelefthandpanel,clickonSave
5.ClickSaveSettingstoFlash,thenclickOK.
Note:ThisstepsavesallconfigurationchangestotheNV‐RAMtoensurethatifthe
switchisrebootedorpowercycled,theconfigurationchangeswillstillbeapplied.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59

Trendnet TPE-TG82ES User manual

Trendnet
Brand
Trendnet
Model
TPE-TG82ES
Category
Network switches
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents