Danfoss Hot Wire Cutter Installation guide

Brand: Danfoss

Model: Hot Wire Cutter

Type: Installation guide

• TheHotWireCutterisprimarilyfortheuse 

 ofcuttingDanfossSpeedUppanelsaswellas

 additionalEPSorXPSinsulation(reproofedto

 DIN4102).

• Pleasebecarefulwhenworkingwiththetool

 topreventaccidentssuchasburningyourself

 oryoursurroundings.Thebladescanreach 

 temperaturesofupto500°C.Nevertouchthe

 bladeaftertheswitchhasbeenpresseddown.

 Donotlaytheunitagainstanysurfaceafter 

 usinguntilthebladehascooleddown.

Do not operate the product in unfavourable

ambient conditions.

Unfavourableambientconditionsare:

• Moistureortoohighairhumidity

• Dustandammablegases,fumesorsolvents

• Strongvibrations.

Introduction

Instruction

Hot Wire Cutter

DanfossHES VI.CT.C1.02 ©Danfoss11/2008 1

Technical data

Cutting blades

Ordering 088X0612

Type SC-11

Operatingvoltage 230V~50-60Hz (110V~50-60Hz)

Powerconsumption 60W

Intermittentoperation 12sON/48sOFF

Weight 1025g

Safety instructions

Observe these safety instructions at all time!



• Theunauthorizedconversionand/ormodica-

tionoftheproductisinadmissiblebecauseof

safetyandapprovalreasons(CE).

• Theconnectioncableistobereplacedonly 

 bythemanufacturerorhisservicingagentwho

 haveaspecialtoolavailable.

• ThestructureoftheHotWireCuttercomplies

 withsafetyclassII.Makesurethattheinsulation

 ofthehousingisneitherdamagednor

 destroyed.

U-formedblade for16mmgrooves

StraightbladetypeC-40 forboardsupto40mm

Always unplug the unit when not used.

Instruction Hot Wire Cutter

Operation

2 VI.CT.C1.02 ©Danfoss11/2008 DanfossHES

1:Unscrewthebindingscrews.

2:Insertthecuttingblade.

3:Tightenbindingscrewsagaincarefully.

4:Beforeyoupluginthetool,checkthevoltage

whichisindicatedonthelabel.

5:Whenyoupressdowntheswitchthecutting

bladeheatsup.Afterabout6-8secs.the

suitablecuttingtemperatureisobtained.

6:Theblademaybecleanedwithametalbrush

whileitisstillwarm.

7:AfterworkingreleasetheswitchoftheHotWire

Cutter.



Do not hold the unit in „ON“ position

continuously to prevent abnormal high

blade temperature.

Allowthebladetocooldownduringoperation. 

Theindication„intermittentoperation1/4min.“

meansthefollowing:

Thetoolisnotdimensionedforcontinuous

operation.After1/4minuteofheatingrespectively

workingwiththetoolitshallcooldownfor3/4

minute.

Disposal

Thedeviceitselfmustnotbedisposedinhouse-

holdrefuse!

Anunusabledevicemustbereturnedtothe

supplier,themanufactureroranocialdisposal

body/institutionequippedforthispurpose.

 ThisdevicefulltherequirementsoftheEU-Directives:

  2004/108/EC: „EMC-Directive“

  2006/95/EC: „LowVoltageDirective“

 ThereforethisdeviceismarkedwiththeCE-Mark.

CE- mark

Danfoss Hot Wire Cutter Installation guide

Danfoss Hot Wire Cutter Installation guide

Danfoss Hot Wire Cutter Installation guide

Related papers

Other documents