2. Danfoss
  3. Hot Wire Cutter

Danfoss Hot Wire Cutter Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss Hot Wire Cutter Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Instruction
Hot Wire Cutter
Introduction
• TheHotWireCutterisprimarilyfortheuse
ofcuttingDanfossSpeedUppanelsaswellas
additionalEPSorXPSinsulation.
• Pleasebecarefulwhenworkingwiththetool
topreventaccidentssuchasburningyourself
oryoursurroundings.Thebladescanreach
temperaturesofupto500°C.Nevertouchthe
bladeaftertheswitchhasbeenpresseddown.
Donotlaytheunitagainstanysurfaceafter
usinguntilthebladehascooleddown.
Do not operate the product in unfavourable
ambient conditions.
Unfavourableambientconditionsare:
• Moistureortoohighairhumidity
• Dustandammablegases,fumesorsolvents
• Strongvibrations.
Always unplug the unit when not used.
Technical data
Cutting blades
Ordering 088X0612
Type FH-TOM
Operatingvoltage 230V~50-60Hz (110V~50-60Hz)
Powerconsumption 60W
Intermittentoperation 12sON/48sOFF
Weight 1025g
Safety instructions
Observe these safety instructions at all time!
Theunauthorizedconversionand/ormodica-•
tionoftheproductisinadmissiblebecauseof
safetyandapprovalreasons(CE).
Theconnectioncableistobereplacedonlyby•
themanufacturerorhisservicingagentwho
haveaspecialtoolavailable.
ThestructureoftheHotWireCuttercomplies•
withsafetyclassII.Makesurethattheinsula-
tionofthehousingisneitherdamagednor
destroyed.
U-formedblade for16mmgrooves
StraightbladetypeC-40 forboardsupto40mm
1
VICTC302©Danfoss02/2010
Instruction Hot Wire Cutter
Operation
1:Unscrewthebindingscrews.
2:Insertthecuttingblade.
3:Tightenbindingscrewsagaincarefully.
4:Beforeyoupluginthetool,checkthevoltage
whichisindicatedonthelabel.
5:Whenyoupressdowntheswitchthecutting
bladeheatsup.Afterabout6-8secs.the
suitablecuttingtemperatureisobtained.
6:Theblademaybecleanedwithametalbrush
whileitisstillwarm.
7:AfterworkingreleasetheswitchoftheHotWire
Cutter.
 Do not hold the unit in „ON“ position
continuously to prevent abnormal high
blade temperature.
Allowthebladetocooldownduringoperation.
Theindication„intermittentoperation1/4min.“
meansthefollowing:
Thetoolisnotdimensionedforcontinuous
operation.After1/4minuteofheatingrespectively
workingwiththetoolitshallcooldownfor3/4
minute.
Disposal
Thedeviceitselfmustnotbedisposedinhouse-
holdrefuse!
Anunusabledevicemustbereturnedtothe
supplier,themanufactureroranocialdisposal
body/institutionequippedforthispurpose.
ThisdevicefulltherequirementsoftheEU-
Directives:
2004/108/EC: „EMC-Directive“•
2006/95/EC: „LowVoltageDirective“•
ThereforethisdeviceismarkedwiththeCE-Mark.
C E - m a r k
!
2
VICTC302©Danfoss02/2010
/