C50.A7110.00E-1
Hardware list
PCI card holder-S(3)
PCI card holder-L(4)
Thumb screw(7)
for PCI card holder
Thumb screw(14)
& rubber ring(14)
for fix HDD
Loosing two thumb screws to release the M/B tray.
Secure the stand-off bolts on the M/B
tray which match with the M/B fix points,
place the M/B on the copper bolt, fasten
the screws to secure.
1
2
3
3-speed fan adjustable
device
for SSI CEB/EEB
The oval hole on M/B tray
designed for special server
boards, please use nut to
hold the copper bolt in place.
3-speed fan
controller
SATA hot swap
raid
5
Aluminum HDD rail(7)
PSU tray(1)
Thumb screw(3)
for HDD extra fixing
Screw(30)
for fix HDD
Door key is attach to
the accessory box
Front door
with lock
5.25" to 3.5"
convertor
5.25" to 3.5"
convertor
1
2
Push to release
Mounting bracket
for SSI CEB/EEB M/B
Remove the plastic slices for
water tube openings.
Loosing four screws remove the
HDD module
Change fan
direction
Also can fit on 5.25" rack tray
OPEN
LOCK
1. Fasten the HDD screws with
anti-vibration rubber rings to the
HDD.
2. Slide the HDD into the HDD cage
with the anti-vibration kit.
Press down the HDD into the slots
to secure.
Adding extra screw to
the HDD cage for extra
security.
Note:
VGA Card Pillar Installation Guide
1
2
3
4
Multi-Position HDD Module
Remove HDD module To the bottom of the case In the 5.25" rack
Hard disk installation for SATA HDD cage
Hard disk installation for modularized HDD cage
PSU installation
Remove four screws at the base
of the case to release the PSU
stand PSU stand before install
the HDD module.
REAR
C50.A7110.00E-2
6
6
4
2
10
8
4
2
8
10
6
2
4
10
8
USB
5
5
3
1
9
7
1394
3
1
7
9
5
1
3
9
7
USB
4
2
10
6
8
3
1
9
5
7
HD AUDIO
AC'97
10
9
8
6
7
5
2
4
1
3
MIC
EAR
Blue(PORT2 L)
Black(SENSE SEND)
Yellow(PORT2 R)
Brown(PORT1 R)
Red(PORT1 L)
Green(SENSE2 RETUR)
KEY
Orange(SENSE1 RETUR)
Black(PRESENCE)
Black(GND)
Black(AGND)
NC
Yellow(R-RET)
KEY
Blue(L-RET)
Red(MIC)
Brown(MIC-PWE)
Yellow(R-OUT)
Blue(L-OUT)
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
KEY
Black(GND)
Green
White
Red
Black(GND)
Green
White
Red
Black(KEY)
White(+12V)
Green(TPB+)
Black(VG)
Blue(TPA+)
SATA Cable
USB
USB
IEEE1394
E-SATA
Connector
Black(GND)
White(+12V)
Red(TPB-)
Black(VG)
Orange(TPA-)
Adjustment for door swing direction
Loose the screws on the top panel plate as show in the
image above.
Remove the door, and place the door on a table top.
Take the spindles off
the top and bottom
plate
Swap the hinge and door stop as
show as the image above
Reverse the step 2 and step 1 to secure the door panel.
A
B
Loose the nut to uninstall
the lock
When lock at A side
When lock at B side
1. Secure all screws, and lock
2. Check the lock working mechanism
swing the right direction
▼
Face to the top of
the front panel.
▼
Face to the top of
the front panel.
Finish.
USB 2.0 flash card reader / writer
Support multiple types of memory card
Thermometer
TR-3A TR-3B
Optional kit
CR-36A CR-36B
C50.A7110.00E-3
/
