Extron XTP T USW 103 4K User manual

Type
User manual

Extron XTP T USW 103 4K is a three-input switcher capable of transmitting DisplayPort, HDMI, or VGA video over shielded twisted pair cable. It supports bidirectional control and Ethernet, featuring an analog audio input, a 15-pin HD connector, an HDMI input, and a DisplayPort input. The unit can be controlled via front panel buttons or through a host device connected to the front panel USB port. Additionally, it offers remote configuration and control options.

Extron XTP T USW 103 4K is a three-input switcher capable of transmitting DisplayPort, HDMI, or VGA video over shielded twisted pair cable. It supports bidirectional control and Ethernet, featuring an analog audio input, a 15-pin HD connector, an HDMI input, and a DisplayPort input. The unit can be controlled via front panel buttons or through a host device connected to the front panel USB port. Additionally, it offers remote configuration and control options.

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
XTP T USW 103 4K • Setup Guide
The XTP T USW 103 4K is a three-input
switcher for extending DisplayPort, HDMI,
or VGA video, audio, bidirectional control,
and Ethernet over a shielded twisted pair
cable. This guide provides instructions for an
experienced installer to install and connect the
Extron XTP T USW 103 4K Universal Switcher.
A
Power connector and LED indicator
B
Analog audio input connector
C
Analog 15-pin HD connector
D
HDMI input connector
E
DisplayPort input connector
F
HDMI output connector
G
XTP output connector
H
LAN connector
I
RS-232 and IR Over XTP connector
J
Contact closure connector
K
Tally Out connector
L
Remote RS-232 connector
Figure 1. XTP T USW 103 4K Rear Panel Features
Installation
Before starting, turn off or disconnect all equipment power sources and mount the switcher on a tabletop or in a rack.
Input and Output Connections
1. Connect an unbalanced analog audio source to the 3.5 mm, TRS connector (see gure 1,
B
). Wire
the connector as shown to the right. Audio from this input can be transmitted with any of the three
video inputs. By default, HDMI embedded audio is given priority.
2. Connect an analog RGB video source to the female 15-pin HD VGA connector, labeled input 1 (
C
).
3. Connect a digital video source to the female HDMI connector, labeled input 2 (
D
). It can accept HDMI, DVI (with an
appropriate adapter), or dual mode DisplayPort video signals.
NOTE: Use an Extron LockIt
®
Lacing Bracket to secure HDMI cables to the rear panel connectors.
4. Connect a DisplayPort video source to the female DisplayPort connector, labeled input 3 (
E
).
5. Connect a digital video display to the HDMI output connector (
F
). A display that is not HDCP-compliant displays a green
screen when HDCP-encrypted content is sent to it.
XTP Interconnections
1. Connect a shielded twisted pair cable between the XTP output connector (
G
) and an XTP receiver or XTP matrix switcher.
ATTENTION: Do not connect this connector to a computer data or
telecommunications network.
The XTP T USW 103 4K is compatible with shielded twisted pair (F/UTP, SF/UTP, and
S/FTP) cable. Extron recommends using the following practices to achieve full
transmission distances up to 330 feet (100 meters) and reduce transmission errors.
Use Extron XTP DTP 24 SF/UTP cable for the best performance. At a minimum,
Extron recommends 24 AWG, solid conductor, STP cable with 400 MHz of bandwidth.
Terminate cables with shielded connectors to the TIA/EIA-T568B standard.
Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
Do not exceed 40% ll capacity in conduits.
Do not comb the cable for the rst 20 meters, where cables are straightened, aligned, and secured in tight bundles.
Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
Separate twisted pair cables from AC power cables.
SIG LINK
LAN
XTP OUT
POWER
XTP T USW 103 4K
12V
1.5A MAX
AUDIO
123
RGB
HDMI DISPLAYPORT
HDMI OUT
Rx GTx
RS-232 IR
RxTx
G
CONTACT
G
RS-232
Tx Rx123
TALLY OUT
+V
123
R
INPUTS
ABCDEF
GH I
JKL
Sleeve ( )
Ring(R)
Tip(L)
3.5 mm Stereo Plug Connector
(balanced)
TIA/EIA-T568B
Pin Wire Color
1
White-orange
2
Orange
3
White-green
4
Blue
5
White-blue
6
Green
7
White-brown
8
Brown
12345678
RJ-45
Connector
Insert Twisted
Pair Wires
Pins:
2
68-3217-50 Rev. A
11 17
© 2017 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
2. Connect a host device or control LAN or WAN to the LAN RJ-45 connector (see f gure 1,
H
on the previous page) for pass-through 10/100BASE-T Ethernet communication. The
LEDs indicate link (green) and activity (amber) status.
3. To pass bidirectional serial or infrared signals to a control or controlled device, connect
the device to the RS-232 and IR Over XTP connector (
I
). Wire the connector as shown
to the right.
Control and Power Connections
For additional wiring considerations, see the XTP T USW 103 4K User Guide at www.extron.com.
1. Connect contact closure devices or Extron “Show Me” cables (see the red pigtail on the
“Show Me” cable in the diagram to the right) to the Contact 4-pole captive screw connector (
J
).
2. Connect tally devices or Extron “Show Me” cables (see the black pigtail on the “Show Me” cable
in the diagram to the right) to the Tally Out 4-pole captive screw connector (
K
).
3. For serial control of the switcher, connect a host device (such as a computer) to the 3-pole
captive screw connector (
L
).
4. Connect a host device to the front panel female USB mini-B connector (see
M
to the right) to
congure the device or update rmware.
5. Power the XTP T USW 103 4K in one of the following methods:
External power supply: Connect the provided external power supply to the 2-pole captive
screw connector (
A
). The corresponding LED indicator lights when the switcher receives power.
PI 140: Connect a PI 140 to the XTP connection between the XTP T USW 103 4K and a locally
powered XTP receiver or XTP matrix switcher
Matrix switcher: Connect the XTP T USW 103 4K to an XTP input board capable of remote
powering 26-watt devices. Enable the remote power feature on the XTP matrix switcher.
Operation
Front Panel Operation
The three front panel buttons with corresponding LEDs (labeled inputs 1-3 or MODE,
NORMAL, and AUTO respectively) select inputs 1 through 3 or enable different operating
modes. The LEDs light to indicate the active input and provide device status feedback.
Input selection
Press the input selection button that corresponds with the desired rear panel input connector to select that input signal.
Auto switch mode
The auto switch mode available from the front panel switches the input to the highest numbered input receiving a video signal.
To enable auto switch mode, press and hold input buttons 1 and 3 simultaneously until the Auto Switch LED lights (after about 3
seconds). To disable auto switch mode, press and hold input buttons 1 and 2 simultaneously until the Auto Switch LED turns off.
Front panel lockout mode
Front panel lockout mode disables input selection from the input selection buttons. To enable or disable front panel lockout mode,
press and hold input buttons 1, 2, and 3 simultaneously until all front panel LEDs blink three times (after about 5 seconds).
Remote Configuration and Control
To directly congure the switcher, connect a host device to the front panel USB port. On the host device, use the Extron XTP
System Conguration Software (recommended) or Simple Instruction Set (SIS) commands in Extron DataViewer (see the
XTP T USW 103 4K User Guide).
Front Panel Indicators
Auto Switch LED — Lights when the device is in auto switch mode.
Input selection LEDs — Light when an input signal is detected on the corresponding input.
Signal Status LEDs — Light when an input signal is detected on the corresponding input.
HDCP Status LEDs — Light when an input signal is HDCP-compliant. Input 1 has no HDCP capabilities.
Audio Signal Clip LED — Lights red when the analog audio input signal remains above -3 dBFS. It remains lit for 200 ms after
the signal falls below -3 dBFS.
G
CONTACT
G
RS-232
Tx Rx123
TALLY OUT
+V
123
Red Black
“Show MeCable
Pigtail
MODE
123
NORMAL
AUTO
1
HDCP
SIGNAL
AUDIO
SIGNAL CLIP
CONFIG
MODE
123
NORMAL
AUTO
XTP T USW 103 4K
AUTO
SWITCH
1
H
D
CP
S
I
G
NA
L
AUDIO
S
I
G
NAL
C
LI
P
MO
DE
1
2
3
N
O
RMA
L
A
UT
O
X
TP T
US
W 103 4
K
M
  • Page 1 1
  • Page 2 2

Extron XTP T USW 103 4K User manual

Type
User manual

Extron XTP T USW 103 4K is a three-input switcher capable of transmitting DisplayPort, HDMI, or VGA video over shielded twisted pair cable. It supports bidirectional control and Ethernet, featuring an analog audio input, a 15-pin HD connector, an HDMI input, and a DisplayPort input. The unit can be controlled via front panel buttons or through a host device connected to the front panel USB port. Additionally, it offers remote configuration and control options.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI