Design House 510297 Installation guide

Design House
Brand
Design House
Model
510297
Type
Installation guide

This manual is also suitable for

Design House 510297 is a ceiling-mounted light fixture designed to provide general illumination in residential and commercial spaces. It features a glass shade that allows for the diffusion of light, creating a soft and inviting ambiance. The fixture can accommodate two 60-watt Type A bulbs, providing ample brightness for a variety of tasks. Installation requires basic electrical wiring knowledge and should be performed by a qualified electrician to ensure safety and proper functionality.

Design House 510297 is a ceiling-mounted light fixture designed to provide general illumination in residential and commercial spaces. It features a glass shade that allows for the diffusion of light, creating a soft and inviting ambiance. The fixture can accommodate two 60-watt Type A bulbs, providing ample brightness for a variety of tasks. Installation requires basic electrical wiring knowledge and should be performed by a qualified electrician to ensure safety and proper functionality.

BRISTOL FLUSH MOUNT CEILING FIXTURE
ASSEMBLY/INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need them at a later date.
CAUTION
GENERAL
All electrical connections must be in accordance with local and National Electrical Code
(N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the
services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are
missing by referencing the illustration.
WARNING: Risk of Fire. Min 90ºC supply conductors. Consult a qualified electrician to
ensure correct installation
Turn off the main power at the circuit breaker before installing the fixture in order to
prevent possible shock.
ASSEMBLY AND INSTALLATION
1. Before installing, preset the NIPPLE length:
a) Thread the HEX NUT onto the NIPPLE, and screw the NIPPLE into the COUPLING
on the CANOPY a minimum of four turns.
b) Place the center holes of the GLASS SHADE over the NIPPLE and adjust the NIPPLE
so that it protrudes out of the CAP 1/4”. Remove the GLASS SHADE & CAP and secure
the NIPPLE in place by tightening the HEX NUT.
2. Pull the SUPPLY WIRES and the SUPPLY GROUND WIRE out from the JUNCTION
BOX and attach the MOUNTING STRAP to the JUNCTION BOX using the slotted holes
on the MOUNTING STRAP and the MOUNTING SCREWS provided.
3. Thread the FIXTURE SCREWS two full turns into the appropriate threaded holes in the
MOUNTING STRAP. (Check the MOUNTING STRAP against the fixture KEY HOLE
SLOTS to ensure proper fit.)
4. Make the wiring connection: Attach the FIXTURE GROUND WIRE to the SUPPLY
GROUND WIRE. Attach both to the MOUNTING STRAP with the GREEN GROUND
SCREW. Connect the BLACK SUPPLY WIRE to the BLACK FIXTURE WIRE and
WHITE SUPPLY WIRE to the WHITE FIXTURE WIRE with WIRE NUTS.
ASSEMBLY AND INSTALLATION
(CONT.)
5. Carefully tuck all wiring back into the JUNCTION BOX. Lift the CANOPY over the
JUNCTION BOX, positioning the FIXTURE SCREWS heads through the large openings
of the KEY HOLE SLOTS. Rotate the CANOPY until the FIXTURE SCREW heads are
seated at the small ends of the KEY HOLE SLOTS, secure them with a screwdriver.
6. Install the bulbs (sold separately). Risk of fire, Use (2) MAX 60W Type A lamps. DO
NOT EXCEED THE MAXIMUM WATTAGE.
7. Place the center hole of the GLASS SHADE over the NIPPLE and secure it with a HEX
NUT. Pass the CAP over NIPPLE and secure it with FINIAL. Restore electric power to
installation point.
# 510297, #504399
Customer Service
1-800-558-8700
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN.
  • Page 1 1

Design House 510297 Installation guide

Design House
Brand
Design House
Model
510297
Type
Installation guide
This manual is also suitable for

Design House 510297 is a ceiling-mounted light fixture designed to provide general illumination in residential and commercial spaces. It features a glass shade that allows for the diffusion of light, creating a soft and inviting ambiance. The fixture can accommodate two 60-watt Type A bulbs, providing ample brightness for a variety of tasks. Installation requires basic electrical wiring knowledge and should be performed by a qualified electrician to ensure safety and proper functionality.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents