FLUSH MOUNT FIXTURE
ASSEMBLY/INSTALLATION INSTRUCTIONS
Please read carefully and save these instructions, as you may need them at a later date.
CAUTION
GENERAL
All electrical connections must be in accordance with local and National Electrical Code (N.E.C.)
standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a
qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are
missing by referencing the illustrations on the installation instructions.
1. OUTLET BOX
2. CROSSBAR
3. MOUNTING SCREW
4. FIXTURE SCREW
5. WHITE SUPPLY WIRE
6. BLACK SUPPLY WIRE
7. SUPPLY GROUND WIRE
8. WHITE FIXTURE WIRE
9. BLACK FIXTURE WIRE
10. FIXTURE GROUND
WIRE
11. WIRE CONNECTOR
12. FIXTURE PAN
13. KEY HOLE SLOT
14. HEX NUT
15. BUSHING
16. NIPPLE
17. GLASS SHADE
18. FINIAL KNOB
19. CAP
20. GREEN GROUND SCREW
WARNING: Risk of Fire. Min 90ºC supply conductors. Consult a qualified electrician to ensure
correct branch circuit conductor.
Turn off the main power at the circuit breaker before installing the fixture, in order to prevent
possible shock.
Fig.1 Fig.2
ASSEMBLY AND INSTALLATION
1. Before installing, preset the NIPPLE (16) length:
a) Thread the HEX NUT (14) onto the NIPPLE (16), and screw the NIPPLE (16) into the
BUSHING (15) on the FIXTURE PAN (12) a minimum of four turns.
b) Place the center holes of the GLASS SHADE (17) over the NIPPLE (16) and adjust the
NIPPLE (16) so that it protrudes out of the GLASS SHADE (17) or CAP (19) about 1/4”.
Remove the GLASS SHADE (17) and secure the NIPPLE (16) in place by tightening the HEX
NUT (14).
2. Pull the SUPPLY WIRES (5 & 6) and GROUND WIRE (7) out from the OUTLET BOX (1)
and attach the CROSSBAR (2) to the OUTLET BOX (1) using the slotted holes on the
CROSSBAR (2) and the MOUNTING SCREWS (3) provided.
3. Thread the FIXTURE SCREWS (4) two full turns into the appropriate threaded holes in the
CROSSBAR (2). (Check the CROSSBAR (2) against the fixture KEY HOLE SLOTS (13) to
ensure proper fit.)
4. Make the wiring connection: Connect the FIXTURE GROUND WIRE (10) to the SUPPLY
GROUND WIRE (7) with a WIRE CONNECTOR (11) (not included) and then attach them to
the CROSSBAR with GREEN GROUND SCREW (20). Connect the BLACK SUPPLY WIRE
(6) to the BLACK FIXTURE WIRE (9) and WHITE SUPPLY WIRE (5) to the WHITE
FIXTURE WIRE (8) with WIRE CONNECTORS (11).
ASSEMBLY AND INSTALLATION (CONT.)
5. Carefully tuck all wiring back into the OUTLET BOX (1). Locate the FIXTURE PAN (12)
over the OUTLET BOX (1), positioning the FIXTURE SCREWS (4) heads through the large
openings of the KEY HOLE SLOTS (13). Rotate the FIXTURE PAN (12) to seat the screws,
and tighten securely. (See Fig. 2 )
6. Install the bulbs (Sold separately). See markings and/or labels on the fixture for maximum
wattages ,DO NOT EXCEED THE MAXIMUM WATTAGE!
7. Place the center hole of the GLASS SHADE (17) over the NIPPLE (16) and secure the GLASS
SHADE (17) with the FINIAL KNOB (18) (See Figure 1) or secure the GLASS SHADE (17)
and CAP (19) with the FINIAL KNOB (18) ( See Fig . 3 ).
NOTE: For safe installation, you can also secure the GLASS SHADE (17) with one HEXNUT
first and then locate the FINIAL KNOB (18) or CAP (19) and FINIAL KNOB (18)
8. INSTALLATION IS NOW COMPLETE. Restore electric power to fixture.
Fig.3
Customer Service 1-800-558-8700
NOTE: Sketches are only for
general reference.
-
1
Design House 519249 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Meridian M70099AV User manual
-
Trend TT80015AB User manual
-
Minka-Lavery 4812-77 User manual
-
Home Decorators Collection 27182 Installation guide
-
Minka Lavery 4960-84 Installation guide
-
Minka Group 893-84 User manual
-
-
Kenroy Home 90903BRZ User manual
-
Quoizel PWL1613WT Installation guide
-
