VISUAL COMFORT S 4044 User manual

Brand: VISUAL COMFORT

Model: S 4044

Type: User manual

VISUAL COMFORT S 4044 is an extra large flush mount light fixture designed for indoor use. It features a sleek and modern design with a glass shade that adds a touch of elegance to any room. Installation requires basic tools and electrical knowledge, including drilling holes, connecting wires, and securing the fixture to the ceiling. The light source is not included and needs to be purchased separately. Once installed, the fixture can be easily cleaned with a soft dry cloth or feather duster. Avoid using abrasive or chemical agents to maintain the finish.

VISUAL COMFORT S 4044 is an extra large flush mount light fixture designed for indoor use. It features a sleek and modern design with a glass shade that adds a touch of elegance to any room. Installation requires basic tools and electrical knowledge, including drilling holes, connecting wires, and securing the fixture to the ceiling. The light source is not included and needs to be purchased separately. Once installed, the fixture can be easily cleaned with a soft dry cloth or feather duster. Avoid using abrasive or chemical agents to maintain the finish.

Shaw Extra Large Flush Mount

Item # S 4044

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver Slotted Screwdriver

NOTICE:

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (C) from fixture body (L) by removing

screws (K).

3. Remove light source (H) from mounting plate (C) by removing

screws (I).

4. Using mounting plate (C) as a guide, line up with the junction box and

mark anchor positions.

5. Using a drill bit slightly smaller than the anchor, drill holes in the

marked positions. Install anchors (B) into the holes using hammer.

6. Install mounting plate (C) to the junction box and secure with

mounting screws (D), then secure wood screws (F) to anchors (B).

7. Run support cable through hole on back of mounting plate (C).

Loosen cable lock and install to end of support cable. Insert other end

of cable through the cable lock and tighten ends with a screwdriver to

secure. (see diagram 1)

8 Remove quick connector (E1) from light source.

9. Wrap quick connector ground wire (bare copper) around the green

grounding screw (see diagram 2). Tighten. Continue quick connector

ground wire and connect to supply ground wire (usually green or bare

copper) using wire nut (A).

NOTE: It is imperative that the fixture is grounded.

Pencil Hammer

Drill

A

B

C

D

E1

F

I

E2

H

US

M

L

I

D

S

E

T

J

K

L

M

Diagram 2

Diagram 1

Shaw Extra Large Flush Mount

Item # S 4044

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

10. Connect quick connector neutral wire (white) to the supply neutral

wire (usually white) using wire nut (A).

11. Connect quick connector hot wire (black) to the supply hot

wire (usually black) using wire nut (A).

CAUTION: Do not reverse the hot and neutral connections.

12. Make sure all wire connections are tight, then carefully tuck into the

junction box.

13. Connect quick connectors (E1 & E2) together, then install light

source (H) to mounting plate (C) and secure with screws (I).

14. Install glass shade (M) to fixture body (L) and secure with screws (J).

NOTE: Do not over-tighten otherwise shade could become damaged.

15. Install fixture body (L) to mounting plate (C) and secure with

screws (K).

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

not use abrasive or chemical agents.

NOTICE:

US

M

L

I

D

S

E

T

A

B

C

D

E1

F

I

E2

H

J

K

L

M

Diagram 2

Diagram 1

1
2

VISUAL COMFORT S 4044 User manual

Brand: VISUAL COMFORT

Model: S 4044

Type: User manual

VISUAL COMFORT S 4044 is an extra large flush mount light fixture designed for indoor use. It features a sleek and modern design with a glass shade that adds a touch of elegance to any room. Installation requires basic tools and electrical knowledge, including drilling holes, connecting wires, and securing the fixture to the ceiling. The light source is not included and needs to be purchased separately. Once installed, the fixture can be easily cleaned with a soft dry cloth or feather duster. Avoid using abrasive or chemical agents to maintain the finish.

Related papers

Other documents