VISUAL COMFORT KW 4521 User manual

Type
User manual

VISUAL COMFORT KW 4521 is an eight-light flush mount designed to provide ample illumination for your living space. It features a metal frame with a matte black finish and clear glass shades that allow for a warm and inviting glow. With its adjustable support cable, you can customize the height of the fixture to suit your needs. Installation requires basic tools and can be completed in a few simple steps. Enjoy the elegant and functional lighting that the VISUAL COMFORT KW 4521 brings to your home.

VISUAL COMFORT KW 4521 is an eight-light flush mount designed to provide ample illumination for your living space. It features a metal frame with a matte black finish and clear glass shades that allow for a warm and inviting glow. With its adjustable support cable, you can customize the height of the fixture to suit your needs. Installation requires basic tools and can be completed in a few simple steps. Enjoy the elegant and functional lighting that the VISUAL COMFORT KW 4521 brings to your home.

Pertica 30" Eight Light Flush Mount
Item # KW 4521
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver
NOTICE:
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove metal plate (F) from mounting plate (B) by removing collar
rings (G).
3. Using mounting plate (B) as a guide, line up with the junction box and
mark anchor positions.
4. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into the holes using hammer.
5. Install mounting plate (B) to the junction box and secure with
mounting screws (E), then secure wood screws (C) to anchors (A).
6. Wrap supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 1). Tighten.
NOTE: It is imperative that the fixture is grounded.
7. Connect fixture neutral wire (white) to the supply neutral wire (usually
white) using wire nut (D).
8. Connect fixture hot wire (black) to the supply hot wire (usually black)
using wire nut (D).
CAUTION: Do not reverse the hot and neutral connections.
9. Make sure all wire connections are tight, then carefully tuck into the
junction box.
NOTE: It is recommended to have a helper assist in supporting the
fixture for steps 10-11.
Pencil Hammer
Drill
A
B
C
D
E
F
G
I
H
US
M
L
I
D
S
E
T
Diagram 2
PERSONS REQUIRED: Two
Diagram 1
Pertica 30" Eight Light Flush Mount
Item # KW 4521
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Run support cable through hole on back of mounting plate (B).
Loosen cable lock and install to end of support cable. Insert other end
of cable through the cable lock and tighten ends with a screwdriver to
secure. (see diagram 2)
11. Install metal plate (F) to mounting plate (B) and secure collar rings (G).
12. Remove protective caps (J) from mounting plate (B), then thread LED
bulbs (H) to metal plate (F) .
NOTE: Confirm all light sources are installed before testing power.
13. Thread shades (I) to metal plate (F).
NOTE: Do not over-tighten otherwise shade could become damaged.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
A
B
C
D
E
F
G
I
H
US
M
L
I
D
S
E
T
Diagram 2
Diagram 1
Pertica 30" Eight Light Flush Mount
Item # KW 4521
UNPACKING NOTICE
Please follow instructions below to avoid possible damages caused by
improper removal.
1. Open box and remove top layer of packaging.
2. Evenly lift shade in areas indicated by arrows (see diagram) until
clear of packaging. Place on clean, soft surface.
NOTE: Remove slowly to avoid damages.
NOTICE:
  • Page 1 1
  • Page 2 2
  • Page 3 3

VISUAL COMFORT KW 4521 User manual

Type
User manual

VISUAL COMFORT KW 4521 is an eight-light flush mount designed to provide ample illumination for your living space. It features a metal frame with a matte black finish and clear glass shades that allow for a warm and inviting glow. With its adjustable support cable, you can customize the height of the fixture to suit your needs. Installation requires basic tools and can be completed in a few simple steps. Enjoy the elegant and functional lighting that the VISUAL COMFORT KW 4521 brings to your home.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI