Ralph Lauren RL 2026 Installation guide

Type
Installation guide

Ralph Lauren RL 2026 is a medium-sized sconce designed to provide ambient lighting in various indoor settings. Its frame and fixture base are made of sturdy materials, ensuring durability and longevity. The sconce features a classic design with glass panels that enhance its aesthetic appeal. Installation requires basic tools and involves connecting wires, securing the mounting plate, and attaching the frame. It accommodates bulbs, allowing for customization of brightness and color temperature.

Ralph Lauren RL 2026 is a medium-sized sconce designed to provide ambient lighting in various indoor settings. Its frame and fixture base are made of sturdy materials, ensuring durability and longevity. The sconce features a classic design with glass panels that enhance its aesthetic appeal. Installation requires basic tools and involves connecting wires, securing the mounting plate, and attaching the frame. It accommodates bulbs, allowing for customization of brightness and color temperature.

1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove frame (F) from fixture base (B) by removing screws (E).
3. Remove mounting plate (K) from fixture (B) by removing threaded
caps (I).
4. Install mounting plate (K) to junction box and secure with mounting
screws (D).
5. Using fixture (B) as a guide, line up with the junction box and mark
anchor positions.
6. Using a drill bit slightly smaller than the anchor, drill holes in the
marked positions. Install anchors (A) into the holes.
7. Wrap fixture ground wire (bare copper) around the green grounding
screw (see diagram 1). Tighten. Continue fixture ground wire and
connect to supply ground wire (usually green or bare copper) using
wire nut (J).
NOTE: It is imperative that the fixture is grounded.
8. Connect fixture neutral wire (white) to the supply neutral wire
(usually white) using wire nut (J).
9. Connect fixture hot wire (black) to the supply hot wire (usually
black) using wire nut (J).
CAUTION: Do not reverse the hot and neutral connections.
Geneva Medium Sconce
Item # RL 2026
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
NOTICE:
Phillips Screwdriver Slotted Screwdriver Drill
Hammer Pencil
A
I
B
E
F
GH
C
J
D K
Bulbs not included
Diagram 1
Geneva Medium Sconce
Item # RL 2026
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Make sure all wire connections are tight, then carefully tuck into the
junction box.
11. Install fixture (B) to mounting plate (K) and secure with threaded
caps (I), then secure wood screws (C) to anchors (A).
12. Install glass panels (G) to frame (F) and secure by bending metal
tabs (H).
13. Install light bulbs into the sockets.
14. Install frame (F) to fixture (B) and secure with screws (E).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
A
I
B
E
F
GH
C
J
D K
Bulbs not included
Diagram 1
  • Page 1 1
  • Page 2 2

Ralph Lauren RL 2026 Installation guide

Type
Installation guide

Ralph Lauren RL 2026 is a medium-sized sconce designed to provide ambient lighting in various indoor settings. Its frame and fixture base are made of sturdy materials, ensuring durability and longevity. The sconce features a classic design with glass panels that enhance its aesthetic appeal. Installation requires basic tools and involves connecting wires, securing the mounting plate, and attaching the frame. It accommodates bulbs, allowing for customization of brightness and color temperature.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI