Ralph Lauren RL5724 is a stunning large linear chandelier that will add a touch of elegance to any room. With its adjustable height and multiple light sources, it's perfect for creating a warm and inviting atmosphere. The RL5724 is easy to install and comes with all the necessary hardware. It's also dimmable, so you can customize the lighting to your liking.
Ralph Lauren RL5724 is a stunning large linear chandelier that will add a touch of elegance to any room. With its adjustable height and multiple light sources, it's perfect for creating a warm and inviting atmosphere. The RL5724 is easy to install and comes with all the necessary hardware. It's also dimmable, so you can customize the lighting to your liking.
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Remove mounting plate (C) from canopy (G) by removing collar
rings (I) and screws (H).
3. Using the mounting plate (C) as a guide, line up with the ceiling and
mark anchor positions.
4. Using drill bit slightly smaller than the anchor, drill holes in the marked
positions. Install anchor (B) into the holes using hammer.
5. Install mounting plate (C) to junction box and secure with mounting
screws (E), then secure wood screws (D) to anchor (B).
6. Feed electrical through bottom rods (K) and connect to fixture
body (L).
7. Continue feeding wires through collar rings (I), canopy (G) and top
rods (J).
NOTE: It is recommended to have a helper assist in supporting the
fixture for steps 8-9.
8. Holding fixture upright, slide collar rings (I) and canopy (G) down
top rods (J) and rest on couplings. Then connect top rods (J) to
bottom rods (K).
NOTE: Slide components down slowly to avoid damages.
Perren Large Linear Chandelier
Item # RL5724
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Wire Cutters
Wire Strippers Drill Hammer
NOTICE:
US
M
L
I
D
S
E
T
PERSONS REQUIRED: Two
A
C
D
E
F
B
J
K
I
L
O
N
M
H
G
O 16pcs
N 16pcs
915 mm
305 mm
Diagram 2
Diagram 1
Input white
wire
Fixture black wire
Fixture black wire
Fixture red wire
Fixture red wire
Input black
wire
Output red
wire
Output black
wire
Output red
wire
Output black
wire
Input white
wire
Input black
wire
Perren Large Linear Chandelier
Item # RL5724
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
9. Hang both sides of fixture by top mount (F) to the center of mounting
plate (B).
10. Cut excess wires, being sure to leave length to reach the junction
box. Separate wires, and strip insulation on each 5/8".
11. Connect fixture neutral wires (black) to the driver output neutral
wires (black) using wire nut (A).
12. Connect fixture hot wires (red) to the driver output hot wires (red) using
wire nut (A). See diagram 1.
13. Connect supply ground wire (usually green or bare copper) around the
green grounding screw (see diagram 2). Tighten.
NOTE: It is imperative that the fixture is grounded.
14. Connect driver input neutral wires (white) to the supply neutral wire
(usually white) using wire nut (A).
15. Connect driver input hot wires (black) to the supply hot wire (usually
black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the
junction box.
17. Install canopy (G) to the mounting plate (C) and secure with collar
rings (I) and screws (H).
18. Install glass rods (O) & (N) to the fixture (L).
19. Thread end caps (M) to the fixture (L).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
A
C
D
E
F
B
J
K
I
L
O
N
M
H
G
O 16pcs
N 16pcs
915 mm
305 mm
Diagram 2
Diagram 1
Input white
wire
Fixture black wire
Fixture black wire
Fixture red wire
Fixture red wire
Input black
wire
Output red
wire
Output black
wire
Output red
wire
Output black
wire
Input white
wire
Input black
wire
Perren Large Linear Chandelier
Item # RL5724
ASSEMBLY INSTRUCTIONS
Please follow instructions below to avoid possible damages caused by
improper removal.
1. Open box and remove top layer of packaging.
2. Evenly lift glass rods in areas indicated by arrows (see diagram 3) until
clear of packaging. Place on clean, soft surface.
3. Remove second layer of packaging, along with mounting plate and
rods and set aside.
4. Remove side styrofoam blocks from packaging then evenly lift fixture
by ribbons, indicated by arrows (see diagram 4) until clear of packaging.
Place on clean, soft surface.
NOTE: Remove slowly to avoid damages.
NOTICE:
US
M
L
I
D
S
E
T
Diagram 3
Diagram 4
-
1
-
2
-
3
Ralph Lauren RL5724 is a stunning large linear chandelier that will add a touch of elegance to any room. With its adjustable height and multiple light sources, it's perfect for creating a warm and inviting atmosphere. The RL5724 is easy to install and comes with all the necessary hardware. It's also dimmable, so you can customize the lighting to your liking.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ralph Lauren RL5724 User manual
-
Ralph Lauren RL2560 User manual
-
-
-
-
-
-
-
Other documents
-
VISUAL COMFORT S 2212 User manual
-
VISUAL COMFORT CHC4400 User manual
-
-
-
-
-
circa LIGHTING PB 5045 User manual
-
-
-
