VISUAL COMFORT TOB 4357 User manual

Brand: VISUAL COMFORT

Model: TOB 4357

Type: User manual

VISUAL COMFORT TOB 4357 is a 17-inch flush mount light fixture that provides ample lighting for any room. It features a glass shade and a metal body with a brushed nickel finish, giving it a modern and stylish look. Installation is easy with the included mounting hardware, and the fixture is suitable for both residential and commercial use. It is also easy to maintain, requiring only a soft, dry cloth or feather duster for cleaning.

VISUAL COMFORT TOB 4357 is a 17-inch flush mount light fixture that provides ample lighting for any room. It features a glass shade and a metal body with a brushed nickel finish, giving it a modern and stylish look. Installation is easy with the included mounting hardware, and the fixture is suitable for both residential and commercial use. It is also easy to maintain, requiring only a soft, dry cloth or feather duster for cleaning.

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove fixture body (D) from mounting plate (A) by unscrewing.

3. Using mounting plate (A) as a guide, line up with the junction box and

mark anchor positions.

4. Using a drill bit slightly smaller than the anchor, drill holes in the

marked positions. Install anchors (L) into the holes using hammer.

5. Install mounting plate (A) to the junction box and secure with

mounting screws (B), then secure wood screws (K) to anchors (L).

6. Remove quick connector (I) from light source.

7. Wrap quick connector ground wire (bare copper) around the green

grounding screw (see diagram 1). Tighten. Continue quick connector

ground wire and connect to supply ground wire (usually green or bare

copper) using wire nut (C).

NOTE: It is imperative that the fixture is grounded.

8. Connect quick connector neutral wire (white) to the supply neutral

wire (usually white) using wire nut (C).

9. Connect quick connector hot wire (black) to the supply hot

wire (usually black) using wire nut (C).

CAUTION: Do not reverse the hot and neutral connections.

Ace 17" Flush Mount

Item # TOB 4357

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

NOTICE:

US

M

L

I

D

S

E

T

Diagram 1

Phillips Screwdriver Slotted Screwdriver

Pencil Hammer

Drill

A

M

L

K

G

N

B

C

E

D

F

J

Diagram 3

Diagram 2

H

I

Diagram 4

M

Ace 17" Flush Mount

Item # TOB 4357

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

10. Make sure all wire connections are tight, then carefully tuck into the

junction box.

11. Connect quick connectors (I & H) together (see diagram 2), then

install light source (J) to threaded nipple (G) and secure with threaded

caps (E).

12. Loosen thumbscrews (N) from shade bracket, then install glass

shade (F) to fixture body (D) and secure with thumbscrews (N).

NOTE: Do not over-tighten otherwise shade could become damaged.

13. Run support cable through hole on bracket (M). Loosen cable lock and

install to end of support cable. Insert other end of cable through the

cable lock and tighten ends with a screwdriver to secure.

(see diagram 3 &4)

14. Align studs (N) on mounting plate (A) with slots on fixture body (D),

then turn clockwise until locked in place. See diagram 5.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

Not use abrasive or chemical agents.

NOTICE:

US

M

L

I

D

S

E

T

A

M

L

K

G

N

B

C

E

D

F

J

O

Diagram 5

1
2

VISUAL COMFORT TOB 4357 User manual

Brand: VISUAL COMFORT

Model: TOB 4357

Type: User manual

VISUAL COMFORT TOB 4357 is a 17-inch flush mount light fixture that provides ample lighting for any room. It features a glass shade and a metal body with a brushed nickel finish, giving it a modern and stylish look. Installation is easy with the included mounting hardware, and the fixture is suitable for both residential and commercial use. It is also easy to maintain, requiring only a soft, dry cloth or feather duster for cleaning.

Download PDF

Related papers

Other documents