VISUAL COMFORT ARN 2651 Installation guide

Brand: VISUAL COMFORT

Model: ARN 2651

Type: Installation guide

VISUAL COMFORT ARN 2651 is a versatile wall-mounted light fixture that offers both portable and hardwire installation options. It features a swing arm that allows you to adjust the angle of the light, making it suitable for various tasks and ambiances. The fixture comes with a shade that helps direct the light and reduce glare. Installation requires basic tools and can be completed by following the step-by-step instructions provided in the manual.

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove portable mounting plate (N) from fixture body (D) by

unscrewing side screws (C).

3. Using the portable plate (N) as a guide, line up with the wall and

mark anchor positions.

4. Using a drill bit slightly smaller than the anchor, drill holes in the

marked positions. Install anchors (I) into the holes using hammer.

5. Install portable mounting plate (N) to wall by securing wood screws (J)

to anchors (I).

6. Install fixture body (D) to portable mounting plate (N) and secure with

side screws (C).

7. Remove socket ring (G) from socket (E), then attach shade (F) to

socket (E) and secure with socket ring (G).

8. Insert light bulb into the socket.

9. Swing the arm to desired angle.

10. Remove the protective plug cover (L) from the plug (K).

11. Plug into a proper electrical outlet and test the fixture.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

not use abrasive or chemical agents.

Keil Large Swing Arm Wall Light

Item #ARN 2651

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver Slotted Screwdriver Drill

Hammer Pencil

NOTICE:

Portable assembly

Bulb not included LK

Diagram 1

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove the portable mounting plate (N) from the fixture body (D) by

unscrewing the side screws (C).

3. Using hardwire mounting plate (A) as a guide, line up with the junction

box and mark anchor positions.

4. Using a drill bit slightly smaller than the anchor, drill holes in the

marked positions. Install anchors (I) into the holes.

5. Install hardwire mounting plate (A) to junction box and secure with

mounting screws (B), then secure wood screws (J) to anchors (I)

using hammer.

6. Remove the portable cord by unscrewing wire nuts (M).

7. Install direct wire plug (H) into the wire exit on the bottom of fixture

body (D).

8. Wrap fixture ground wire (bare copper) around the green grounding

screw (see diagram 1). Tighten. Continue fixture ground wire and

connect to supply ground wire (usually green or bare copper) using

wire nut (I).

NOTE: It is imperative that the fixture is grounded.

9. Connect fixture neutral wire (white) to the supply neutral wire

(usually white) using wire nut (I).

10. Connect fixture hot wire (black) to the supply hot wire (usually

black) using wire nut (I).

CAUTION: Do not reverse the hot and neutral connections.

Keil Large Swing Arm Wall Light

Item #ARN 2651

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

NOTICE:

Hardwire assembly

Bulb not included

TOOLS REQUIRED (NOT INCLUDED):

Phillips Screwdriver Slotted Screwdriver Drill

Hammer Pencil

Diagram 1

11. Make sure all wire connections are tight, then carefully tuck into the

junction box.

12. Install fixture body (D) to hardwire mounting plate (A) and secure

with side screws (C).

13. Remove socket ring (G) from socket (E), then attach shade (F) to

socket (E) and secure with socket ring (G).

14. Insert light bulb into the socket.

15. Swing the arm to desired angle.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do

not use abrasive or chemical agents.

Keil Large Swing Arm Wall Light

Item #ARN 2651

ASSEMBLY INSTRUCTIONS

This light fixture should be installed in accordance with all applicable,

local installation codes, and by a person familiar with the construction

and operation of it, as well as the hazards involved. Inspect item and

contents carefully. If any damage or defect is found, do not install.

Retain all packaging material until installation is complete and approved.

NOTICE:

Hardwire assembly

Bulb not included

VISUAL COMFORT ARN 2651 Installation guide

VISUAL COMFORT ARN 2651 Installation guide

VISUAL COMFORT ARN 2651 Installation guide

Related papers

Other documents