Extron MTP U R A User manual

Extron
Brand
Extron
Model
MTP U R A
Category
Video switches
Type
User manual

This manual is also suitable for

IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
MTP U R Series • Setup Guide
RGB
DELAY
PEAKING
LEVEL
MTP U R RSA SEQ
R
G
B
SELECT
ADJUST
SIGNAL
AUDIO
RS-232
VID
Y/C
YUV
RGB
This card provides quick start instructions for an experienced installer to set up
and operate any of the MTP U R Series products.
JMP1
JMP3
JMP2
Default settings
(viewed from rear)
Pre-installation — Jumper Settings
The MTP U R has three jumpers located on the main board. JMP1 is RS-232 directional communication,
and JMP2 and JMP3 are for vertical and horizontal sync (respectively). By default JMP1 is bidirectional;
JMP2 and JMP3 are negative sync.
Installation
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert Twisted
Pair Wires
Pins:
1 2345678
RJ-45
Connector
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP U R as required.
Step 2 — Connect Input
Connect the RJ-45 cable from an MTP transmitter to the Input port on the MTP U R. Terminate the
cable as shown on the right, using the same standard (A or B) at both ends.
POWER
12V
0.5A MAX
CAT 7 INPUT
NOTE: If the input is labeled “CAT 7 Input”, only a CAT 7 cable should be used (that is, MTP C7 U R RSA SEQ model).
Step 3 — Connect Outputs
RGB
1
MONO AUDIO
2
VID
Y/C
B-Y
Y
R-Y
OUTPUTS
RS-232
Tx Rx
SPACE
Attach the applicable output cables (video, audio, and RS-232), depending on the MTP U R model used.
• Composite video output connector — Connect to the single female BNC connector (VID) .
• S-video output connector — Connect to the 4-pin mini DIN connector (Y/C).
• Component video (MTP U R RSA SEQ model only) — Connect to the three female BNC
connectors (Y, R-Y, and B-Y).
• High resolution video output connector — Connect to the 15-pin HD connector (RGB).
• RS-232 connector — Connect a serial communications port to the upper 3.5 mm,
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected RS-232
Device Pins
MTP/HDMI U R
Pins
Spare
Spare
5-pole captive screw connector for bidirectional RS-232 communication (as shown).
• Audio connector (MTP U R RSA SEQ and MTP U R A models only) — Connect a suitable audio device
audio device to the lower 5-pole captive screw connector for mono audio output (as shown).
1
MONO AUDIO
2
1
MONO AUDIO
2
Unbalanced Output
Balanced Output
Do not tin the wires!
Mono output 1-
Sleeve(s)
Mono output 1+
Mono output 2+
Mono output 2-
Sleeve(s)
Mono output 1
Mono output 2
NO GROUND.
NO GROUND.
Step 4 — Power
Plug the included external 12 VDC power supply into the 2-pole captive screw connector. Wire the
connector (see image a on the right).
Grounding guidelines
Extron MTP U R products can be adversely affected by electrostatic discharge (ESD) if they are not
grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP U R product in either of two ways:
• Ground the power input port — Insert one end of the grounding wire to the negative or ground pin on
the power input connector (see image a on the right). Tie the other end of the wire to an earth ground.
• Ground the chassis — Use a connector hex nut as shown in image b the right. Tie the other end of
the wire to an earth ground.
If you have any questions about how to ground a product in a specic application, contact an Extron technical
support specialist.
a
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
POWER
12V
xA MAX
Tie
Wrap
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
b
68-1367-50
Rev. B
01 13
MTP U R Series • Setup Guide
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566
FAX
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91-80-3055.3777
+91 80 3055 3737
FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
Step 5 — Input Signal Detection
Check the displayed output is correct. The MTP U R detects the input signal format, indicated by the front panel LEDs (VID, Y/C,
YUV, RGB), and differentiates between RS-232 and audio signals. The output is then made on the appropriate connector and
all other outputs are muted.
Step 6 — Peaking and Level
RGB
PEAKING
LEVEL
MTP U R RS SEQ
Image sharpness is adjusted with the Peaking Control. Increased peaking compensates for mid- and
high-frequency detail loss. Minimum setting (full counterclockwise) is zero peaking.
Image brightness is adjusted using the Level Control. View the image and adjust the control for the best image quality.
Step 7 — Skew Compensation
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have built-in
RGB
DELAY
PEAKING
LEVEL
MTP U R RS SEQ
R
G
B
SELECT
ADJUST
SIGNAL
VID
Y/C
YUV
RGB
skew compensation capabilities. Adjust the equalization as follows:
A. Zero the skew delay for red, green, and blue by using a Tweeker or small screwdriver to press and hold the Select
button for 3 seconds. When the Red, Green, and Blue LED’s all go out, release the Select button.
B. Use UTP cable test equipment or examine the displayed image to determine which video signal (red, green, or
blue) is shifted furthest to the right.
C. Adjust the furthest left video signal towards the right by using a Tweeker or screwdriver to press and release the
Select button until the LED for the left-shifted color lights.
D. Slowly rotate the Adjust control clockwise until the shifted color is properly aligned.
E. Repeat steps C and D to align the third color if needed.
INPUT
RGB
POWER
12V
0.5A MAX
VID
Y/C
OUTPUTS
MTP U R RS
1
MONO AUDIO
2
INPUT
AUDIO
MONITOR
POWER
12V
.5A MAX
OUTPUT
MTP T 1 5H D A
PRE-PEAK
ON
OFF
L
R
INPUT
MTP T SV A
S-VIDEO
OUTPUT
12V
0.5a
MAX
RESET
ETHERNET
ACT
LINK
AUDIO INPUTS
OUTP UT S
RGB
RGB
1
2
3
1
2
3
Tx Rx
1
1
2
2
1
2
3
1
2
4
1
2
LOCAL INPUTS
RGB
RGB
LOCAL OUTPUTS
INPUT SELECT
ON
LOCAL
RJ - 45
1 2 3 4
RS-232/RS-422
REMOTE
CONTROL
LOCAL RS - 232
Tx Rx
Tx Rx
Tx Rx
Tx Rx
Tx Rx
Tx Rx
Tx Rx
INPU TS
1 2 3 4 5 6 7 8
9 10 11 12 13 14
15 16
1 2 3 4 5 6 7
8
9 10 11 12 13 14 15 16
1 2 3 4
5 6 7
8
INPUT
RGB
POWER
12V
0.5A MAX
VID
Y/C
OUTPUTS
MTP U R A
1
MONO AUDIO
2
DVD-RW/-R RECORDING
Precision Cinema Progressive
Extron
MTPX 1616 Plus
MTP Matrix Switcher
Extron
MTP U R A
Universal Receiver
Extron
MTP U R RS
Universal Receiver
Extron
MTP T 15HD A
Tr ansmitter
Extron
MTP T SV A
Tr ansmitter
PC
DVD
Projector
Flat Panel
Display
Figure 1. Example of a Typical MTP U R Series Application
  • Page 1 1
  • Page 2 2

Extron MTP U R A User manual

Extron
Brand
Extron
Model
MTP U R A
Category
Video switches
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents