Extron MTP RL 15HD RS & MTP RL 15HD RS SEQ User manual
- Category
- Video switches
- Type
- User manual
This manual is also suitable for
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
MTP 15HD RS Series • Setup Guide
This card provides quick start instructions for an experienced installer to set up and operate any of the MTP VGA video and RS‑232 transmission
systems.
Pre-installation — RS-232 Jumper
JMP1
JMP2
JMP3
Unjumpered for
One-way (Default)
Jumpered for
Two-way
The receiver’s RS‑232 circuits are factory‑set to be one‑way, transmitter to receiver. If the system has only one
receiver, jumper JMP 1 on the main board can be set for two‑way communication as shown at right.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the MTP transmitter and up to eight receivers
as required.
Step 2 — Transmitter Inputs
INPUT
Tx Rx
RS-232
MONITOR
• Connect a computer (VGA) video source to the Input connector.
• Connect a VGA monitor to the Monitor connector.
• Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown below.
Ground
Tx
Rx
Gnd
Receive
Transmit
Connected
RS-232
Device Pins
MTP
Pins
12345678
Insert Twisted
Pair Wires
Pins:
NOTE: If you are using Enhanced Skew-Free™
A/V cable, use the TIA/EIA T568A standard only.
Pin
1
2
3
4
5
6
7
8
T568A
Wire Color
White-green
Green
White-orange
Blue
White-blue
Orange
White-brown
Brown
T568B
Wire Color
White-orange
Orange
White-green
Blue
White-blue
Green
White-brown
Brown
Step 3 — TP Cables Between Units
• Terminate a TP cable as shown at right. Connect it between the transmitter’s Output port and the
receiver’s Input port (both ends must match).
NOTE: If the unit is labeled “C7,” only CAT 7 cable should be used.
• For daisy-chaining, connect up to eight TP cables between a receiver’s Buffered
Output port and a daisy‑chained receiver’s Input port.
OUTPUT
Tx Rx
RS-232
Step 4 — Receiver Outputs
• Connect a VGA monitor to the Output connector.
• Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown in step 2, above.
Step 5 — Receiver DIP Switches
• H Sync and V. Sync switches — Set these switches up for positive sync or down for negative sync.
ON
1 2 3 4 5 6
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
END UNIT
• Composite Sync, (SOG), and Video switches — Set these switches as shown in the following table to output the
indicated format.
Output Format C Sync SOG Video
RGBHV
RGBS
RGsB
Component*
S‑Video*
Composite*
NOTE: * Input video format must match.
• End Unit switch — Set this switch up if either of the following is true:
• The receiver being congured is the only receiver connected to the transmitter.
• The receiver being congured is the last receiver in a daisy‑chained system.
68‑925‑50
Rev. B
01 13
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA ‑ West Extron USA ‑ East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.EXTRON
+4000.398766
Inside China Only
+86.21.3760.1568
+86.21.3760.1566
FAX
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
Inside India Only
+91‑80‑3055.3777
+91 80 3055 3737
FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
MTP 15HD RS Series • Setup Guide
Step 6 — Power
Wire the 2‑pole captive screw connectors for the included external 12 VDC power supplies (see image a
on the right). Plug them into all units.
Grounding guidelines
Extron MTP 15HD RS products can be adversely affected by electrostatic discharge (ESD) if they are
not grounded correctly.
To prevent malfunctions or product damage, an experienced installer can correctly ground an
Extron MTP 15HD RS product in either of two ways:
• Ground the power input port — Insert one end of the grounding wire to the negative or ground
pin on the power input connector (see image a on the right). Tie the other end of the wire to an
earth ground.
• Ground the chassis — Use a connector hex nut as shown in image b on the right. Tie the other
end of the wire to an earth ground.
If you have any questions about how to ground a product in a specic application, contact an Extron technical
support specialist.
Step 7 — Pre-Peak, Peaking, and Level
• Transmitter Pre-Peak switch — View the image and set the Pre‑Peaking switch for the best image
quality to correct for long cable runs of the entire system (including all daisy‑chained receivers).
• Receiver Peaking control — View the image and adjust the Peaking control for the best image. Minimum setting
RGB
PEAKING
LEVEL
(full counterclockwise) is zero peaking.
• Receiver Level control — View the image and adjust the Level control for the best
brightness level.
Step 8 — Skew Compensation (SEQ Receivers)
Pair skew can be measured with test equipment or by viewing a crosshatch test pattern. The SEQ receivers have built‑in
skew compensation capabilities. Adjust the equalization as follows:
A. Zero the skew delay for red, green, and blue by using a small screwdriver to press and hold the Select button for
3 seconds. When the Red, Green, and Blue LEDs all go out, release the Select button.
B. Use UTP cable test equipment or examine the displayed image to determine which video signal (red, green or blue)
DELAY
RED
GREEN
BLUE
SELECT
is shifted furthest to the right.
C. Select the furthest left video signal by using a small screwdriver to press and release the Select button until the LED
for the left‑shifted color (Red, Green, or Blue) lights.
D. Slowly rotate the Adjust control clockwise until the selected color is properly converged.
E. If the remaining colors are left shifted, repeat steps C and D.
INPUT
Tx
Rx
RS-232
MONITOR
POWER
12V
.5A MAX
OUTPUT
MT P T 15H D RS
PRE-PEAK
ON
OFF
RGBHV
RGBHV
RGBHV
RS-232
RS-232
RS-232
Rack Mounted
PC
DisplayDisplay
Up to Eight
Total Receivers
Extron
MTP T 15HD RS
Extron
MTP RL 15HD RS SEQ
Extron
MTP RL 15HD RS SEQ
INPUT
BUFFERED
OUTPUT
OUTPUT
POWER
12V
.5A MAX
ON
1 2 3 4 5 6
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
SPARE
1
MONO AUDIO
2
MT P R L 15H D A SE Q
INPUT
BUFFERED
OUTPUT
OUTPUT
POWER
12V
.5A MAX
MT P R L 15H D A
MT P R L 15H D A SE Q
ON
1 2 3 4 5 6
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
SPARE
1
MONO AUDIO
2
TP Cable
TP Cable
Figure 1. Example of a Typical MTP 15HD RS Application
a
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
POWER
12V
xA MAX
Tie
Wrap
Rear
Panel
Ridges
Earth
Ground
3/16"
(5 mm)
Max.
b
-
1
-
2
Extron MTP RL 15HD RS & MTP RL 15HD RS SEQ User manual
- Category
- Video switches
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron SEQ 100 User manual
-
Extron MTP 1500RL 15HD A SEQ User manual
-
Extron electronics MTP RL 15HD RS & MTP RL 15HD RS SEQ User manual
-
-
-
Extron electronics MTPX Plus 128 User manual
-
-
Radio Shack R52S User manual
-
-
Extron electronics VersaTools MTP DA8 User manual
Other documents
-
Extron electronic TP T A 45 User manual
-
Extron electronics VersaTools MTP 15HD A Series User manual
-
Extron electronics TP R BNC A User manual
-
Extron electronics TP T 15HD A User manual
-
Extron electronics Stereo Receiver MTP R 15HD RSA D User manual
-
Extron electronics MTP C7 T 15HD RS User manual
-
Extron electronics MTP U Series User manual
-
Extron electronics MTP 15HD RS Series User manual
-
-
Extron electronics DA4 User manual
