Jamara Gee Bee Z 00 6131 Instructions Manual

  • Hello! I am an AI chatbot trained to assist you with the Jamara Gee Bee Z 00 6131 Instructions Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Instructions
Please read these instructions carefully before starting to build the
model and retain them afterwards for future reference!
Gee Bee Z
Part.-No. 00 6131
GB
Safety Instructions
This model is not a toy!
Not suitable for under 14 year olds!
* Beginners should seek the help of an experienced modeler
to ensure the safe operation of the model
* Assemble the model away from small children
* Observe all of the safety instructions when assembling
the model. You are responsible for its safe operation
* Keep these instruction for reference even after you have
completed the model
!
2
Contents
Safety Information
General Information
Technical Specifications
Safety information 2
General Information 2
Technical Specifications 2
Kit Contents 3
Building the Kit 3-9
Control Throws and C of G 9
Recommended Accessories 9
Building Plans 10-12
Wingspan approx. 800 mm
Length approx. 750 mm
Weight approx. 720 g ( Ready to Fly )
RC 4 Channel / 4 Servos
Motor Electric Motor
Flying models are not toys, and should only be operated by respon-
sible clear thinking people. Assembling and maintaining models
requires a basic level of technical skill, and a sensible logical ap-
proach. Any error in building, repairing or maintaining the model
could result in serious injury or damage. Technical problems or an
incorrectly assembled model may lead to the propeller unexpect-
edly beginning to turn. Always stay out of the vicinity of rotating
propellers and never allow any item to come into contact with a
spinning prop. As neither the manufacturer or the dealer has any
influence over the way that models are operated they can accept
no responsibility for and damage caused.
If this model is the first radio controlled model which you are at-
tempting to build or fly, you should secure the assistance of an
experienced model pilot. Your local dealer will be able to assist
you in locating your local model aircraft club or experienced pilots
in your area. NEVER fly your model over people and never operate
the model in way which may endanger people or animals. Before
your first flight you should conduct a range check of the radio con-
trol system, secure the model to a solid object, and ensure that you
have full control of all functions with the antennae collapsed over a
distance of at least 25 metres. Before and after every flight inspect
the model for damage, and rectify any faults before you attempt to
take off. The operator is responsible for any damage caused by the
operation of flying models.
Always observe any local laws regarding the operation of model
aircraft.
Furthermore, the following instructions must be followed:
*The kit contains small parts which may cause choking if swallow
ed, keep away from small children.
*The model should not be changed in any way, doing so will invali-
date the guarantee.
*Never come into contact with rotating parts.
*Do not fly over wet ground or grass as water will damage the
models electrical components
*Do not expose the model or batteries to direct sunlight, always
keep them in the shade.
*Inspect the model before and after every flight for damage.
*Only ever fly the model if it is in perfect working order.
*The model can only be flown in good weather. Do not fly in wind,
rain or thunder storms.
*Find a place to fly which complies with any laws, and is free from
obstacles such as trees, houses or power cables.
*Remember that your model is made from such materials as plastic
and wood, and as such is inflammable. Keep it away from any open
flame, or high temperatures.
*When operating the model, switch on the transmitter first and
then the aircraft, switch off in the reverse order.
*Always ensure that the throttle stick is in the low position before
you switch on.
As the company JAMARA Modelltechnik has no influence over the
use, maintenance or conditions under which our products will op-
erate, we accept no responsibility for any damage caused be it of
a physical, financial or theoretical nature. JAMARA Modelltechnik
will accept no claim against it which results directly or indirectly
from the operation or use of its products.
Warning!
In some countries it is a legal requirement to carry third party in-
demnity insurance when operating a radio controlled model.
Please ask your local dealer, governing body or your insurance com-
pany for details.
Warning!
Always switch on the transmitter first, and then the model. Switch
off the model first, and then the transmitter.
3
Kit Contents
• CNC laser cut formers and ribs, strip and sheet from selected
light weight balsa and ply
• Fitting kit, including wheels, undercarriage, horns and hinges
etc.
• Clear canopy
• Instructions
Building the Model
Assemble 2 fuselage halves as shown ensuring that you build a left and a right hand side.
Warning, Engine side thrust: The shorter side should be on the right in the direction of flight to accommodate the engine side thrust.
Glue the battery plate and wing nount between thew fuselage
sides followed by teh fuselage upper decking..
Warning, Engine side thrust: The sorter side of the upper deck-
ing should be on the right hand side in the direction of flight!
Glue the engine bulkhead into place.
The lower decking can now be fitted and the rear of the fuselage
can be pulled together. The vertical upper and lower rear formers
can now be glued into the correct positions.
Glue the 4 front fuselage rings on and sand the edges down.
Glue the stringers into the slots, the stringers will protrude approx.
1.5mm out of the of the side formers.
4
Building the Model
Elevator cut out
Glue the fin into place ensuring that it is vertical and square along
the fuselage.
5
Building the Model
Build the battery cover and use 1.5 mm sheet to plank it.
Mount the rudder as shown here but do not glue the hinges yet.
Use 1.5 mm sheet to plank the upper fuselage over the 3 mm stingers only as shown here.
6
Building the Model
Assemble the elevator and fit it temporarily to the fuselage. Adjust
the fit until the elevator is horizontal.
Sand all of the edges round.
Assemble 2 cowl rings as shown here.
The front ring is a made of 3 laminations.
Glue the horizontal spacer plates into position.
Use sheet to plank the cowl and then glue the front ring on.
Building the Model
Glue on the 4th and last ring which is 6 mm thick on and sand the
edges off.
Glue the undercarriage strengtheners between the ribs as shown.
The cowl is glued to the fuselage after covering.
Once the lower sheeting has been fitted, build the lower wing fair-
ing and use 1.5mm sheet to plank it.
8
Building the Model
Glue 6 laminations together to make the wheel pants.
Cut a channel into the front and rear of the undercarriage fairings
to allow the undercarriage leg wires to be let-in.
Use scrap ply to strengthen the axle mounting points.
9
Zusammenbau
Control Throws and C of G:
Recommended Accessories
Elevator: +/- 15 mm
Rudder: +/- 30 mm
Aileron: +/- 12-15 mm
Centre of Gravity: 53 mm Behind the leading edge
This shows how the wheel pants are glued to the undercarriage
wire and the wing.
Motor A2820/6
Part No. 132820
Battery Pack
LiPo Star 11,1 V 2200 mAh
Part No. 14 1776
Or
ESC Xetronic 50 A
Part No. 08 1950
Propeller
APC Electric 11 x 7
Part No. 34 0063
4 x Servos High End Micro
Part No. 03 3212
Battery Pack
LiPo Star 11,1 V 2500 mAh
Part No. 14 1778
10
Building Plan - The original sized plan can be found on the DVD
Wings
Bauzeichnung - Die Originalgrösse finden Sie auf der beiliegenden DVD
11
Fuselage Side


All right reserved
Copyright JAMARA e.K. 2009
Reproduction in part or whole
only with the expressed permission of JAMARA e. K.
JAMARA e.K.
Inh. Erich Natterer
Am Lauerbühl 5 - DE-88317 Aichstetten
Tel. +49 (0) 75 65/94 12-0 - Fax +49 (0) 75 65/94 12-23
[email protected] www.jamara.de
Top View
Aktuelle Neuheiten erfahren Sie in unserem Newsletter. Sollten Sie daran Inter-
esse haben, abbonieren Sie den Jamara Newsletter.
Ihre E-mail-Adresse
______________________________________________________
You can receive up-to-date news through our newsletter. If you are interested, plese
apply for the Jamara Newsletter.
Your E-mail-Address
______________________________________________________
Newsletter
Building Plan -
The original sized plan can be found on the DVD
/