Kichler Lighting 59031BKTLED User manual

Brand
Kichler Lighting
Model
59031BKTLED
Type
User manual
IS-59030LED-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
RIGID STEM MOUNT
1) Pass xture wires through desired number of stems[A] and screw stems
together using supplied short threaded tubes[B].
NOTE: Thread locking compound must be applied to all stem threads as
noted with symbol (4) to prevent accidental rotaon of xture during
cleaning, relamping, etc.
2) Screw rst stem into coupling[N] aached to xture.
3) Pass xture wires from last stem through one short threaded tube[B].
4) Screw short threaded tube into top of last stem.
5) Pass xture wires through hole in canopy[G]. Lower canopy down towards
stem. Pass hole in canopy over end of short threaded tube on top of stem.
6) Pass xture wires through lockwasher[D] and then through hexnut[E]. Place
lockwasher onto end of short threaded tube protruding from inside canopy
and thread hexnut onto tube.
NOTE: Fixture wire should not be cut shorter than 20 inches from above the
canopy.
7) Find the appropriate threaded holes on mounng strap[F]. Assemble
mounng screws[M] into threaded holes.
8) Aach mounng strap to outlet box[C] using the strap mounng screws[H].
Mounng strap can be adjusted to suit posion of xture.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw,
and thread into hole.
b) On xtures where a cupped washer is provided,aach ground wire from
outlet box under cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture ground wire to outlet
box ground wire with wire connector aer following the above steps. Never
connect ground wire to black or white power supply wires.
10) Make wire connecons. Reference chart below for correct connecons and
wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws through holes in
canopy[G].
NOTE: Be certain wires do not get pinched between mounng strap and
canopy, or canopy and ceiling.
12) Use knobs[J] to secure canopy. Tighten to secure.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before
starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical
Code (NEC) and all local code specicaons. If you are not familiar with code
requirements, installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
[A] Stems
[B] Short Threaded
Tubes
[C] Outlet Box
[D] Lockwasher
[E] Hexnut
[F] Mounting Strap
[G] Canopy
[H] Strap Mounting
Screws
[I] First Loop
[J] Knobs
[K] Second Loop
[L] Chain Link
[M] Mounting Screws
[N] Coupling
Installaon Instrucons
LOOP / CHAIN LINK MOUNT
1) Follow steps 1 - 2 from “Rigid Stem Mount” Instrucons.
2) Pass xture wire from last stem through short threaded tube[B] and through
rst loop[I]. Screw short threaded tube into top of last stem and into rst loop.
3) Pass xture wire through second loop[K], short threaded tube, and hole in
canopy[G]. Screw short threaded tube into end of second loop.
4) (If second loop is already aached to canopy, proceed to next step). Insert
short threaded tube at end of second loop through hole in canopy. Thread lock
washer[D] onto short threaded tube protruding from inside canopy. Pass xture
wire through hexnut[E] and thread hexnut onto end of short threaded tube.
NOTE: Fixture wire should not be cut shorter than 20 inches from above the
canopy.
5) Aach open chain link[L] to loop at end of stem(s) and to loop on canopy. Once
aached, close the open chain link by placing a piece of cloth over the open link
and using a pair of pliers to gently squeeze the link closed.
6) Follow steps 7 - 12 from “Rigid Stem Mount” Instrucons.
K
L
B
A
►
►
►
B
A
J
B
G
C
F
M
H
D
E
N
►
►
I
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 59031BKTLED User manual

Brand
Kichler Lighting
Model
59031BKTLED
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents