IS-52234-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Rotate xture arms into their correct posions as shown (Figure 1).
2) Pass xture wire from main frame[I] through large loop[J].
3) Screw large loop onto threads protruding from top of main frame.
4) Take threaded pipe[L] from parts bag and screw in screw collar loop[B] a minimum
of 6 mm (1/4”). Lock into place with hexnut[C].
5) Run another hexnut down threaded pipe almost touching rst hexnut. Now screw
threaded pipe into mounng strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe must protrude out the back
of mounng strap. Screw third hexnut onto end of threaded pipe protruding from
back of mounng strap.
6) Connect mounng strap[D] to outlet box using the strap mounng screws[K].
7) Unscrew the threaded ring[F] from screw collar loop. Take canopy[G] and pass over
screw collar loop. Approximately one half of the screw collar loop exterior threads
should be exposed. Adjust screw collar loop by turning assembly up or down in
mounng strap. Remove canopy.
8) Aer desired posion is found, ghten both top and boom hexnuts up against the
boom and top of the mounng strap.
9) Slip canopy over screw collar loop and thread on threaded ring.
10) Aach one end of chain[H] to boom of screw collar loop[B] by spreading end link
and then closing the link. Aach opposite end of chain to large loop[J] by spreading
opposite end link and then closing the link. To close the open chain links, place a piece
of cloth over the open link and use a pair of pliers to gently squeeze the link closed.
11) Unscrew threaded ring[F], let canopy[G] and threaded ring slip down.
12) Weave electrical wire and ground wire through chain links[H] no more than 3 inches
apart. Pass wire through screw collar loop[B], threaded ring[F], canopy[G], threaded
pipe[L], and into outlet box[E].
13) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a hole and two raised
dimples, wrap ground wire from outlet box around green ground screw, and
thread into hole.
b) On xtures where a cupped washer is provided, aach ground wire from outlet
box under cupped washer and green ground screw, then thread into mounng
strap.
If xture is provided with ground wire, connect xture ground wire to outlet box
ground wire with wire connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
14) Make wire connecon. Reference chart below for correct connecons and wire
accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply Wire
to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or Black
without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other than
green) with silver conductor
*Note: When parallel wire (SPT 1 &
SPT 2) are used. The neutral wire
is square shaped or ridged and the
other wire will be round in shape or
smooth (See illus.)
Neutral Wire
15) Raise canopy to ceiling.
16) Secure canopy in place by ghtening threaded ring onto screw collar loop.
17) Slip one cup[M] down over end of threaded tube[N]. Screw threaded tube into
boom of coupling[A] in the center of socket cluster.
18) Screw hexnut[O] on threaded tube up against boom of coupling.
19) Slip decorave tube[P] over threaded tube. Slip other cup[M] over end of threaded
tube, up against decorave tube.
20) Slip steel washer[Q] over end of threaded tube, up against boom of cup.
21) Slip rubber washer[R] onto end of threaded tube, up against steel washer.
22) Li glass[S] over end of threaded tube, up against rubber washer. Slip another steel
washer[Q] over threads protruding out boom of glass and screw hexnut[O] onto
threads to secure.
23) Slip trim piece[T] over threads protruding below hexnut, making sure threads pass
through center hole in trim piece.
24) Screw nial[U] onto threads protruding out boom of trim piece to secure trim
piece.
25) Install the recommended bulbs (not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starng and
during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical Code
(NEC) and all local code specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Coupling
[B] Screw Collar Loop
[C] Hexnut
[D] Mounting Strap
[E] Outlet Box
[F] Threaded Ring
[G] Canopy
[H] Chain
[I] Main Frame
[J] Large Loop
[K] Strap Mounting
Screws
[L] Threaded Pipe
[M] Cup
[N] Threaded Tube
[O] Hexnut
[P] Decorative Tube
[Q] Steel Washer
[R] Rubber Washer
[S] Glass
[T] Trim Piece
[U] Finial
Figure 1
H
B
G
E
D
C
K
L
F
J
I
M
N
P
M
Q
R
Q
O
T
U
O
S
A
1
2
3
Kichler Lighting 43324DAG User manual
Kichler Lighting 43256DAW Installation guide
Kichler Lighting 52304BK User manual
Kichler Lighting 52277NI User manual
Kichler Lighting 52231BK User manual
Kichler Lighting 52305BK User manual
Kichler Lighting 52077PAL User manual
Kichler Lighting 52078PAL User manual
Kichler Lighting 52079PAL User manual
Kichler Lighting 52275NI User manual
Kichler 52109OZ Operating instructions
Home Decorators Collection 9401010820 Operating instructions