Paxton Proximity Slimline Reader Owner's manual

Paxton
Brand
Paxton
Model
Proximity Slimline Reader
Category
Access cards
Type
Owner's manual
PROXIMITY slimline reader (697-411BL/WT)
Contents in box
PROXIMITY slimline reader
PROXIMITY slimline back plate
Fitting kit
PROXIMITY slimline reader instructions
Suitability
Products
The reader is designed to work with the Switch2 control unit (405-321) and the PC based Net2 control unit
(489-334).
PROXIMITY cards
All Paxton Access Ltd PROXIMITY tokens will work with this reader. They include the PROXIMITY card,
PROXIMITY keyfob and PROXIMITY ISO card.
Read range
The PROXIMITY slimline reader has a read range of 100mm when PROXIMITY cards are used in
normal
conditions and 55mm when PROXIMITY keyfobs are used in normal conditions.
Environment
The reader will operate between –20
o
C and +70
o
C. It can be mounted onto a metal frame, but this may
reduce the read range.
Where to use PROXIMITY slimline
YES NO Reason why not
Low to high use doors Behind Metal RF will not penetrate
Inside and outside Very near to TV or Monitor RF will interfere with reader
No need to shelter from the elements
Narrow door frames and inside walls
Architecturally sensitive installations
Fitting
1. Using the base plate as a template, mark
and drill holes for the cable and the four
screws.
PROXIMITY
slimline reader
securing screw
6 x 3/4
Wall plugs
Cable
2. Tap the four small raw plugs into the wall.
Fix the base plate securely with the screws
provided.
3. Feed the reader cable through the back
plate and hang the reader at an angle over
the back plate. Then slot the reader into
the groove at the top of the base plate and
press the reader into place.
4. Screw in the securing screw at the base of
the reader.
IMPORTANT NOTE: When fitting 2 readers for read in and
read out, the PROXIMITY readers MUST be more than 1ft apart!
INS-137 Date code: 180101
Wiring
NOTES
The reader will be sent out with an RJ45 connector on it. This can be cut off and the cable can be stripped
back ready for wiring.
Brown
Yellow
Blue
Mauve
Black
Net2
1 Door
Access Control Unit
Reader 2 Keypad 2
Brown
Yellow
Orange
Red
Brown
Orange
Green
Yellow
Blue
Mauve
Blk/Wht
Network
Screen
IN-A
IN-B
OUT-A
OUT-B
Reader 1 Keypad 1
Brown
Yellow
Orange
Red
Brown
Orange
Green
Yellow
Blue
Mauve
Blk/Wht
+12V
Gen O/P
Relay 2Inputs
N.C.
N.O.
Com
N.C.
N.O.
Com
0 V
0 V
Exit
0 V
PSU
0V
Power
Contact
Tamper
Door relay 1
12V
5V
OK
Tamper
Contact
Exit
Relay 2
Door relay
Tx
Rx
PSU
Red 12Vdc
PROXIMITY
slimline reader
Orange
Green
PROXIMITY
slimline reader
Red 12Vdc
Brown
Orange
Green
Yellow
Blue
Mauve
Black
Attach
Q.C. Label
here
Red
Brown
Orange
Green
Yellow
Blue
Mauve
Exit
Contact
Black
Card reader or keypad
12v
0v
N.C.
N.O.
Com
Bell
PowerDoor relay
Alarm
Control
unit
Inputs
witch
2
S
** IMPORTANT **
Please note that the red wire should be connected to 12V only. This supersedes the information in the
trade brochure.
Cable extensions
The reader comes with 3 Meters of non-screened cable. The type of cable used to extend this distance will
effect the maximum distance the reader can be extended. All distances are assuming that the reader is wired
according to our instructions.
Maximum distance from ACU
ACU used
CR9538 CR9540
Net2 ACU 100M 100M
Switch2 ACU 100M 100M
Be sure, when extending the cable distance beyond 3M, to keep the colours the same throughout the run.
INS-137 Date code: 180101
  • Page 1 1
  • Page 2 2

Paxton Proximity Slimline Reader Owner's manual

Paxton
Brand
Paxton
Model
Proximity Slimline Reader
Category
Access cards
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents