Zippity Outdoor Products ZP19055 Installation guide

Brand
Zippity Outdoor Products
Model
ZP19055
Type
Installation guide
1
www.zippity-outdoor.com
ASSEMBLY
INSTRUCTIONS
PORTABLE PUPPY FENCE KIT -
2 PACK (22in H x 44in W)
30 MIN approximate assembly
time for 2 fence panels
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
support@zippity-outdoor.com
704-892-5222 / 877-234-6196
zippity-outdoor.com
2www.zippity-outdoor.com
GENERAL INFORMATION
IMPORTANT
• Please read through before starting assembly.
• Important: Check the inside of the larger pieces in your box for other materials packed inside.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
MISSING OR DAMAGED PARTS?
CALL US FIRST SO WE CAN HELP YOU RIGHT AWAY!
Although great care has been taken to ensure proper packaging and handling of this product, occasionally problems occur.
If you discover any missing, damaged or defective parts, please contact our customer service department.
EMAIL: support@zippity-outdoor.com
PHONE: 704-892-5222 / 877-234-6196
Customer service agents are available to take calls weekdays from 8am-5pm EST.
To help you quickly and accurately, please have reference item number ZP19055 and the specic part name which can be
found on the next page. It is helpful if you can provide the batch lot which is a stamped number on the end of the box.
NEED ASSEMBLY HELP?
If you are having problems with the assembly or installation of this product, we are happy to assist you with the process, so
please give us a call at 704-892-5222 / 877-234-6196.
NEED TO RETURN?
If for some reason you need to return this product, please allow us to help resolve your issues rst. If you still decide to
return the product, you will need to intitate the return from the company you originally purchased from.
3
www.zippity-outdoor.com
STEP 1: LAY OUT MATERIALS
PORTABLE PUPPY FENCE KIT 2 PACK
TOOLS YOU WILL NEED
Cordless Drill
Tape Measure
A
D
F
B C
E
G
H
I
J
K
Post Caps (4)
Top Rails (2) -
1 ½” x 1 ½” x 44”
Bottom Rails (2) -
1 ½” x 1 ½” x 44”
Pickets (26) -
¼” x 1 ¼” x 20 ¼”
Posts (4) -
7
/
8
” x 1 ½” x 23”
Rail End Caps (8)
(4 are installed,
4 are loose)
Connector Pin (4)
¾” Steel Screws (16)
(Bag A)
1 ½” Steel Screws (8)
(Bag B)
Silicon No-Scratch
Pads (8)
Portable Feet (4) -
7
/
8
” x 1 ½” x 12”
4www.zippity-outdoor.com
STEP 2: ASSEMBLE FENCE FRAME
STEP 2.1 1. Identify the top rail (D) and the bottom rail (E) as shown below.
2. Insert two loose rail end caps (B) ensuring they are oriented as shown below.
STEP 2.2 STEP 2.3
1. Orient two posts (G) as shown.
2. Slide the the top rail down the posts
aligning the pre-drilled holes.
3. Drive (4) ¾” screws (I) into the pre-drilled
holes.
1. Slide the bottom rail down the posts until
the pre-drilled holes align.
2. Drive (4) ¾” screws into the holes.
1
2
Top rail will have picket
holes on the top and
bottom of the rail.
D
E
B
1
2
3
This will be the top of the fence.
Align
Align
GG
D
I
NOTE: Ensure that the picket holes in the
bottom rail are facing towards the top rail.
1
2
Align
Align
E
5
www.zippity-outdoor.com
STEP 3: INSERT THE PICKETS
STEP 4: ATTACH THE FEET
STEP 3.1
STEP 4.1
1. Rotate the fence frame so that the post tabs are facing up.
2. Insert (13) pickets (F) into the picket holes in the top and bottom rails.
1. Identify the portable feet (C). If you plan to use your portable fence indoors, indentify (4) of the silicon no-scratch
pads (K).
2. Remove the adhesive cover from the pads and stick two pads on the far ends of the underside of each foot as
shown below.
F
1
2
K
C
NOTE: This step is only needed for indoor applications.
1
2
6www.zippity-outdoor.com
STEP 4.2aSTEP 4.2b
1. Take one of the portable feet (C) and
slide the notched end into the underside of
the bottom rail.
1. Take a portable foot (C) and slide the
notched end under the bottom rail. Slide the
foot so that it is touching the side of the post.
Corner/Angled Applications In-Line Applications
1
2
3
4
Underside of fence
J
4.5 in
2. Position the foot so that it is at least 4.5” from the edge of
one of the posts. Drive two 1.5” steel screws (J) through the
predrilled holes in the underside of the portable foot.
3. Take the other portable foot and slide the notched end into
the underside of the rail.
4. Slide the foot until it touches the other post and drive one
1.5” screw into the the pre-drilled hole in the side of the porta-
ble foot.
2. Drive one 1.5” steel screw (J) into the pre-drilled hole in the
side of the foot.
3. Repeat this process on the other side of the fence panel.
1
3
3
2
JJ
7
www.zippity-outdoor.com
STEP 5: ASSEMBLE SECOND FENCE PANEL
STEP 6: CONNECT THE PANELS
STEP 5.1
STEP 6.1
Repeat steps 2-4 to assemble the second fence panel.
Connect the two fence panels using the connector pins (H) as shown below.
H
8www.zippity-outdoor.com
STEP 7: ATTACH POST CAPS
OPTIONAL STEP 8: SECURING PANELS
@
6935 Reames Rd. Ste. K. Charlotte, NC 28216
support@zippity-outdoor.com
704-892-5222 / 877-234-6196
zippity-outdoor.com
STEP 7.1
STEP 8.1
Insert (4) post caps (A) over the top of the posts until the post cap snaps into the tabs of the post.
If you wish to more permanently secure your portable fence you may take the following steps to do so:
1. If mounting on grass and wanting to further secure your fence, you can drive a ½” diameter rebar stake (not
included) into the two holes in each portable foot.
2. Secure a zip tie or cotter pin (not included) through the holes in the connector pin to prevent it from being able
to be removed.
12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Zippity Outdoor Products ZP19055 Installation guide

Brand
Zippity Outdoor Products
Model
ZP19055
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents