OneSpace 50-700505 User guide

Brand: OneSpace

Model: 50-700505

Type: User guide

MODEL # 50-700505

SUPPLIER CODE: PMEX

ASSEMBLY INSTRUCTIONS

OneSpace is a Trademark of Comfort Products, Inc.

™

Adina 2 Drawers Writing Desk, Black

2 OF 12

Desktop maximum

weight capacity

= 40lbs

Drawer maximum

weight capacity

= 10lbs

3 OF 12

- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.

- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.

- OPEN THE HARDWARE AS NEEDED.

- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.

- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.

- HAVE THE TOOLS BELOW BEFORE YOU BEGIN ASSEMBLING.

- NEVER FORCE THE SCREWS OR FITTINGS.

- KEEP THIS MANUAL FOR FUTURE REFERENCE.

- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.

- DO NOT SHIFT OR DRAG THE PRODUCT AFTER ASSEMBLY.

CLEANING AND CARE

- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.

- DO NOT USE ABRASIVE CLEANERS.

- DO NOT USE FURNITURE WAX OR POLISH AS THE UNIT

IS FINISHED WITH A PROTECTIVE CLEAR LACQUER.

- THE FOLLOWING TOOLS ARE NOT INCLUDED.

Drawer Front Panel

Drawer Left Panel

Drawer Right Panel

IF YOU ARE MISSING ANY OF THE PARTS ABOVE, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT

REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE PART

WILL NORMALLY BE SHIPPED WITHIN 48 HOURS.

ROUND STICKER

51-700505HA

51-700505A51-700505G

51-700505H

51-700505I

51-700505J

51-700505K

51-700505Z

51-700505B

51-700505C

51-700505D

51-700505E

51-700505F

predrilled holes.

Screw two Drawer Slides (3-CL) to the Left Outside Shelf Panel (E) using Euro Screws (4).

Then screw two Drawer Slides (3-CR) to the Right Side Panel (B) using four Euro Screws (4).

THIRD

LAST HOLE

SECOND

HOLE

Screw Left Outside Shelf Panel (E) to Bottom Shelf Panel (F)

with one Unitar Screw (5) using predrilled holes.

(Make sure nished sides are facing outwards)

Attach Back Panels (D and K) to Side Panels (A and B) with six Unitar Screws (5) using predilled holes

(making sure both Back Panels nished ends are facing inside and towards each other).

Then, using rubber hammer, hammer four plastic Nail Legs (6) into the bottom of Side Panels (A and B).

Attach Shelf Panels (E and F) with three Unitar Screws (5) using predrilled holes

(making sure nished side is facing front of desk).

Caution:

Do not over tighten

cams.

Press in each of the ve Cams (7), making sure the arrow on top is pointing towards the smaller hole.

Attach Desktop (C) to desk by aligning the Minix Bolts (2) into the smaller holes. Turn the Cam clockwise

to lock it into the Minix Bolt (2).

Attach Sides of Drawer (H and I) to Drawer Front Panel (G) by rst pressing each Cam (7)

into the larger hole, making sure the arrow is pointed towards the smaller hole. Align

Minix Bolts (2) with the smaller holes. Turn each Cam clockwise to lock it into the Minix

Bolt (2).

Slide Drawer Bottom Panel (Z) between Panels (I and H).

(Making sure nished side is facing inside the drawer).

Then attach Drawer Back Panel (J) with four Long Screws (8) into predrilled holes.

Attach Handle (9) to Drawer Front Panel with two Screws (9),

making sure the lip of the handle is facing the bottom of the drawer.

Attach Drawer Slides (10) to the bottom of drawer using four Short Screws (11).

10-DR attaches to Panel (I) and 10-DL attaches to Panel (H)

THIRD TO

LAST HOLE

THIRD

HOLE

Use the eight Round Stickers (12) to cover all exposed screws on the exterior of your

new desk.

•

12 OF 12

DO NOT stand on the desk. Do not use the desk as a stepladder.

DO NOT use the desk unless all bolts and screws are rmly secured.

Every 6 months, check all bolts and screws to ensure they are tight.

This product is California 93120 Compliant for Formaldehyde.

Comfort Products, Inc.

P.O. Box 999

Memphis, TN 38101

PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION

Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by

Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products’ authorized dealers

as shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of

parts at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts

to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is

performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or

disassembly; defects occurring after purchase due to product modication, intentional damage, re, misuse, negligence, or exposure

to the elements; labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort

Products be liable in either tort or contract for any loss or direct, special, incidental, consequential or exemplary damages. This Limited

Warranty is NOT applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies only to end-user

customers in the United States. All warranties are limited to the original purchaser for normal use. The weight capacity is dened as

40 pounds for the desktop and 10 pounds for the drawers. For claims or questions concerning this warranty, please visit:

www.comfortproducts.net or email us at: [email protected]

MODEL: # 50-700505

www.comfortproducts.net

[email protected]

OneSpace is a Trademark of Comfort Products, Inc.

™

OneSpace 50-700505 User guide

OneSpace 50-700505 User guide

OneSpace 50-700505 User guide

Related papers

Other documents