Page is loading ...
Sofa-WallBed
|
ASSEMBLY MANUAL
Inova LLC 2 Van Buren Blvd. Guilderland Center, NY 12085
Sofa-WallBed
|
ASSEMBLY MANUAL
Inova LLC 2 Van Buren Blvd. Guilderland Center, NY 12085
QUEEN SIZE
QUICK START GUIDE
Sofa-WallBed
|
ASSEMBLY MANUAL
Tech support is readily available if needed
Email: support@inovabed.com
Phone: 866.528.2804
Sofa-WallBed
|
ASSEMBLY MANUAL
PLEASE NOTE: Your Bed may look different
than what is shown in the pictures and
videos throughout this manual
QUICK START GUIDE
HELPFUL
IN F ORMAT ION
• Prior to opening your shipment, check and
confirm the room is completely ready to
receive the furniture
(see “Room Readiness Checklist” below).
• Place the parts in the room according to the
sequence of the assembly steps to avoid
double handling
• The Hardware Box is located on the pallet
and labeled “Hardware”
• Hardware is packed by STEP #, not PART #
• A large, contractor’s garbage bag is included in
the Hardware Box for trash removal
• All parts are labeled for easy identification
• Labels will not be seen once the Bed is
completely assembled; the part label is a sticker
and can be removed if desired.
• Each page of the assembly includes a “QR Code”,
which is linked to a video for each step. To view,
download a compatible QR Code App to view
videos or go directly to YouTube (include link).
Tech support is readily available if needed
Email: support@inovabed.com
Phone: 866.528.2804
Sofa-WallBed
|
ASSEMBLY MANUAL
PLEASE NOTE: Your Bed may look different
than what is shown in the pictures and
videos throughout this manual
ROOM READINESS
CHECKLIST
• Check room to confirm the ceiling, floor,
and walls in the room are finished
and completed
• Select the wall and location in which the
Bed will be placed
• Measure the length of the wall and height
of ceiling to confirm the Bed will fit
TIP: You may want to remove existing
baseboard that is located on the wall where
the Bed will be installed. By removing the
baseboard, it will allow for a tighter fit
against the wall (custom units may already
have a notch for baseboard – see shop
drawings, if applicable).
• Locate any electrical outlets on the wall
that may be covered up by the Bed
• Clear out any items in the room so you
have a clear path to the wall and an open
area to assemble the Bed
• If the flooring is hard, lay down some
furniture blankets, sheets of cardboard, or
other cushioning material to prevent parts
from being scratched.
• Locate the maress that will be used with
this Bed; the specific maress is required
for proper adjustment of the Bed and
completion of the assembly
QUICK START GUIDE
(CONT.)
Tech support is readily available if needed
Email: support@inovabed.com
Phone: 866.528.2804
Sofa-WallBed
|
ASSEMBLY MANUAL
PLEASE NOTE: Your Bed may look different
than what is shown in the pictures and
videos throughout this manual
QUICK START GUIDE
(CONT.)
TOOLS NEEDED:
Electric Power Drill
#2 Phillips Bit
#3 Phillips Bit (provided)
#2 Square Bit (provided)
4mm Allen Wrench (provided)
4mm Allen Bit (provided)
9/16” Wrench
#2 Phillips Screwdriver
Hammer
Pliers
Utility Knife
Vise Grips
Flashlight
QR Code Scanner App
(To view videos)
HARDWARE LIST:
Bolts:
H-021 Panel Bolts, 40 mm
H-068 Panel Bolts, 2”
H-112 Flange Head Bolts, 5/16” x 2”
H-162 Panel Bolts, 30mm
H-738 Flange Bolts 5/6” x 1-1/2”
H-920 Bolts, 3/8” x 3”
H-923 Bolts, 5/16” x 1”
Screws:
H-014s Euro Screws
H-019 Machine Screws, 10-32 x 3/4”
H-065 Panel Screws, 50mm
H-087 Pan Head Screws, 5/8”
H-088 Machine Screws, 1/4”-20 x 1/2”
H-107s Flat Head Euro Screws
H-114 Panel Screws, 1/4” x 2-1/2”
H-184 Auger Screws, 1”
H-425 Machine Screws, 25mm
H-739 Cap Screws, 5/16” X 1-1/4”
H-766 Machine Screws, 10-32 x 1”
H-924 Machine Screws, 1/4”-20 x 3/4”
Nuts:
H-086 Flange Nuts, 5/16”
H-189 Nuts, 3/8”
H-767 Nylock Nuts, 5/6”
H-919 Nylock Nuts, 3/8”
Other:
H-003 Wood Dowels
H-011 Minifix Pins
H-062 Double-Ended Minifix Pin
H-067 Washers, 3/4”OD x 5/16” ID
H-073 Washer Head Euro Screws
H-077 Wide Angle Brackets
H-085 Mending Plates
H-187 Washers, 1”OD x 7/16”ID
H-921 Rollers, 1”
Headoard Guides
Sofa-WallBed: Hardware Overview
H-065
H-021
H-085
H-062
H-068
H-067
H-011
H-003
H-077
H-019
H-073
H-014s
The illustrations drawn are general representations of your product’s hardware.
H-162
H-107s
H-187
H-143
H-184
H-088
H-086
H-114
H-087
H-112
Sofa-WallBed: Hardware Overview, cont.
The illustrations drawn are general representations of your product’s hardware.
H-739
H-425
H-189
H-738
H-923
Headboard Guide
H-766
H-920
H-767
H-210
H-924
H-921
H-919
Sofa-WallBed: Hardware Overview, cont.
The illustrations drawn are general representations of your product’s hardware.
A. Lay the Right Pier on the floor as shown.
B. Screw the H-011 Minifix Pins into the small
holes.
C. Tap the H-003 Wood Dowels into the larger
holes.
STEP 1 OPEN BACK: Prepare Right Pier
Pier, Right
H-003
H-011
Use this version of Step 1 if your Sofa-WallBed is an Open Back Model
A. Lay the Right Pier on the floor as shown.
B. Screw the H-011 Minifix Pins into the small
holes.
C. Tap the H-003 Wood Dowels into the larger
holes.
STEP 1 CLOSED BACK: Prepare Right Pier
H-003
H-011
Pier, Right
Use this version of Step 1 if your Sofa-WallBed is a Closed Back Model
A. Hold the Valance next to the Cabinet Top
B. Screw the Valance to the Cabinet top with
H-065 Panel Screws using a 4mm Allen
Wrench.
C. Hold the Shelf next to the Cabinet Back.
D. Screw the Shelf to the Cabinet Back with
H-065 Panel Screws using a 4mm Allen
Wrench.
STEP 2 OPEN BACK: Attach Valance to Cabinet Top & Attach Shelf to Cabinet Back
A
Cabinet Top
Valance
B
H-065
Cabinet Top
Valance
C
Shelf
Cabinet Back
D
H-065
Cabinet Back
Shelf
Use this version of Step 2 if your Sofa-WallBed is an Open Back Model
A. Hold the Valance next to the Cabinet Top
B. Screw the Valance to the Cabinet top with
H-065 Panel Screws using a 4mm Allen
Wrench.
C. Hold the Shelf next to the Closed Back.
D. Screw the Shelf to the Closed Back with
H-065 Panel Screws using a 4mm Allen
Wrench.
STEP 2 CLOSED BACK: Attach Valance to Cabinet Top & Attach Shelf to Closed Back
A
Cabinet Top
Valance
B
H-065
Cabinet Top
Valance
C
Shelf
Closed Back
D
H-065
Shelf
Closed Back
Use this version of Step 2 if your Sofa-WallBed is a Closed Back Model
A. Lay the Right Pier from Step 1 on the floor
as shown, using padding to protect it from
geing scratched.
B. Slide the Cabinet Back/Shelf Assembly onto
the fiings in the Right Cabinet Side and
tighten the Minifix Cams.
C. Slide the Cabinet Top Assembly onto the
fiings in the Right Cabinet Side and tighten
the Minifix Cams.
STEP 3 OPEN BACK: Attach Cabinet Top and Cabinet Back to Right Pier
Use this version of Step 3 if your Sofa-WallBed is an Open Back Model
Pier, Right
Cabinet Back
Cabinet Top
A. Lay the Right Pier from Step 1 on the floor
as shown, using padding to protect it from
geing scratched.
B. Slide the Closed Back/Shelf Assembly onto
the fiings in the Right Cabinet Side and
tighten the Minifix Cams.
C. Slide the Cabinet Top Assembly onto the
fiings in the Right Cabinet Side and tighten
the Minifix Cams.
D. Screw the Cabinet Top to the Closed Back
using H-065 Panel Screws using a 4mm Allen
Wrench.
STEP 3 CLOSED BACK: Attach Cabinet Top and Closed Back to Right Pier
Use this version of Step 3 if your Sofa-WallBed is a Closed Back Model
Pier, Right
Closed Back
H-065
Cabinet Top
A. Lay the Le Pier on the floor as shown.
B. Screw the H-011 Minifix Pins into the small
holes.
C. Tap the H-003 Wood Dowels into the larger
holes.
STEP 4 OPEN BACK: Prepare Left Pier
Use this version of Step 4 if your Sofa-WallBed is an Open Back Model
H-011
H-003
Pier, Left
A. Lay the Le Pier on the floor as shown.
B. Screw the H-011 Minifix Pins into the small
holes.
C. Tap the H-003 Wood Dowels into the larger
holes.
STEP 4 CLOSED BACK: Prepare Left Pier
Use this version of Step 4 if your Sofa-WallBed is a Closed Back Model
H-003
H-011
Pier, Left
A. Make sure all the Minifix Cams have their
arrows pointing to the nearest edge of the
panels.
B. Li the Le Pier, flip it over, and place it on
the partly assembled cabinet as shown. You
may need to shi the parts slightly to get the
dowels and pins to line up with the holes.
C. Tighten all the Minifix Cams as in Step 3.
STEP 5 OPEN BACK: Attach Left Pier to the Cabinet Assembly
Use this version of Step 5 if your Sofa-WallBed is an Open Back Model
Cabinet Back
Pier, Left
Cabinet Top
A. Make sure all the Minifix Cams have their
arrows pointing to the nearest edge of the
panels.
B. Li the Le Pier, flip it over, and place it on
the partly assembled cabinet as shown. You
may need to shi the parts slightly to get the
dowels and pins to line up with the holes.
C. Tighten all the Minifix Cams as in Step 3.
STEP 5 CLOSED BACK: Attach Left Pier to the Cabinet Assembly
Use this version of Step 5 if your Sofa-WallBed is a Closed Back Model
Closed Back
Pier, Left
Cabinet Top
A. Carefully lay the Cabinet over as shown
using padding on the floor to protect the
cabinet from being scratched.
B. Locate the Cabinet Boom and the Le and
Right Baseplates. Lay them on the floor as
shown with the pre-installed metal minifix
cams facing upwards. Insert a H-062 Double
Ended Minifix pin in each of the edge holes
on the Cabinet Boom that are in line with
a minifix cam. Turn the Minifix Cams 180º.
Insert H-003 Wood Dowels into the other
edge holes. Push the Baseplates against the
Cabinet Boom so that the other ends of the
Double Ended Minifix pins are aligned with
the edge holes. Turn the Minifix Cams in the
Baseplates until the panels are pulled tight.
C. Maneuver the Baseplate Assembly into
position as shown and aach it to the boom
of the cabinet using H-021 40mm Panel Bolts.
Make sure that the cams are facing away
from the cabinet as shown.
STEP 6: Attach Baseplate Assembly to Cabinet
A
Base Plate, Left
B
Cabinet Bottom
H-062
H-003
Base Plate, Right
C
H-021
/
