OneSpace HMOF User manual

OneSpace
Brand
OneSpace
Model
HMOF
Type
User manual

This manual is also suitable for

7
CRAFT STATION WITH STOOL, BLACK AND SILVER
ASSEMBLY INSTRUCTIONS
MODEL 50-CS03
SUPPLIER CODE: HMOF
For fastest service on claims, requests for replacement parts,
www.comfortproducts.net/support
e-mail: customerservice@comfortproducts.net
Keep your sales receipt as documentation of your ownership.
CUSTOMER SERVICE
or questions, please visit our website at:
OneSpace is a Trademark of Comfort Products, Inc.
™
Desktop Maximum
weight capacity
Drawer maximum
weight capacity
= 10 lbs
Stool maximum
weight capacity
=
150 lbs
=
130 lbs
ASSEMBLY OVERVIEW (50-CS03)
2 of 10
THE PART NUMBER CAN BE FOUND ON THE SIDE OF THE PART, EITHER STAMPED OR ON A STICKER.
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST 1 OF 3 (50-CS03)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
#
DESCRIPTION SIDE 1 SIDE 2
STOCK #
QTY.
1 Desktop 51-CS03DT 1
2
Side Stand Top
51-CS03ST 1
3
Lower Support
Board
51-CS03SBL 1
4 Bottom Shelf
51-CS03BS 1
5
Right Leg for
Desk
51-CS03LEGR 1
Upper Support
Board
51-CS03SBU 1
6
Left Leg for
Desk
51-CS03LEGL 1
Lift 51-CS03LFT 1
7
8
3 of 10
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST 2 OF 3 (50-CS03)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
#
DESCRIPTION
STOCK #
QTY.
Right Drawer
Frame
51-CS03DFR 1
10
Left Drawer
Frame
51-CS03DFL 1
11
Lower Crossbar 51-CS03CRL 2
Upper Crossbar 51-CS03CRU 2
L-Bracket 51-CS03LB 2
Glide 51-CS03GL 4
12
Drawer with
Bottom Piece
51-CS03DWR 3
13
14
9
Leg for Side
Stand
51-CS03LEGST
1
Metal Lip 51-CS03LIP 1
15
16
17
4 of 10
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST 3 OF 3 (50-CS03)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
#
DESCRIPTION
STOCK #
QTY.
Stool Leg A 51-CS03SLA 1
Stool Leg B 51-CS03SLB 1
19
Round Support
Frame
51-CS03RSF 1
Stool Cushion 51-CS03SC 1
20
21
18
5 of 10
6 of 10
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
HARDWARE LIST (50-CS03)
PART DESCRIPTION
QT
Y.
A
M6 X 15MM 2
C
8
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED .
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE A SCREWDRIVER BEFORE YOU BEGIN ASSEMBLING
(NOT INCLUDED).
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE A POWER DRILL.
HARDWARE KIT
STOCK # 51-CS03HA
D
K
M6 x 20MM
M6 x 55MM
Allen Wrench
8
B
M6 x 28MM
4
M6 x 30MM
4
Nut
4
M5 x 60MM
8
M4 x 22MM
4
M4 x 16MM
2
E
F
G
H
I
J
M6 x 12MM
8
1
Extra Hardware (A - J) 1 set
IF YOU ARE MISSING ANY OF THESE PARTS, OR IF YOU HAVE A DAMAGED PART, PLEASE VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF THIS MANUAL. SIMPLY COMPLETE THE INFORMATION, INCLUDING THE PART YOU NEED. THE
PART WILL NORMALLY BE SHIPPED WITHIN 48 HOURS.
ASSEMBLY INSTRUCTIONS (50-CS03)
7 of 10
STEP 1
NOTE: To distinguish between the left and right legs, note the extra holes in the right leg.
Attach the Right (6) and Left (7) Legs of the desk to the Lower Support Board (3) and
the Bottom Shelf (4) using eight Screws (H). Attach the Upper Support Board (5)
using four Screws (C). Use the Allen Wrench (K) to tighten the screws.
STEP 2
Place the Desktop (1) upside down on a soft surface. Flip the assembled frame over
and place it on the Desktop with the screw holes positioned as shown. Attach the
frame to the Desktop using the two L-Brackets (9) with four Screws (A) and two Screws (B)
(For each bracket use two Screws (A) to attach it to the Desktop (1) and one Screw (B) to
attach it to the leg).
Attach the Lift (8) to the Desktop (1) and the Upper Support
Board (5) using four Screws (A).
Screw the Glides (10) into the bottom of the legs.
K
K
7
10
1
9
9
6
4
5
8
5
3
Cx4
Hx8
C
C
H
Ax8 Bx2
A
A
B
B
ASSEMBLY INSTRUCTIONS (50-CS03)
8 of 10
STEP 3
STEP 4
Insert two Screws (C) through the Right Leg (6) and the Left Frame (12) and attach to the Upper Crossbars (14). Using the other
two Screws (C) do the same with the Side Stand Leg (16) and the Right Frame (11). Rotate the Upper Crossbars so that the
screw holes are facing up and down.
Attach the Side Stand Top (2) to the Upper Crossbars (14) with four Screws (I).
K
K
13 (no screw holes
in the middle)
2
6
16
Cx4
Dx8
I x4
C
D
D
D
C
I
I
14 (with holes)
11
12
NOTE: The Upper Crossbars (14) have holes in the middle to attach to the Side Stand Top. The Lower Crossbars (13) do not.
Attach the Left (12) and Right (11) Drawer Frames to the two Lower Crossbars with four Screws (D). Use the outer screw holes
at the bottom corners of each frame.
With the remaining screw holes at the bottom of the frames, use two Screws (D) to attach the Left Frame (12) to the
Right Leg (6) of the desk (this leg is on the left in the drawing below) and two more Screws (D) to attach the Right Frame (11)
to the Side Stand Leg (16).
ASSEMBLY INSTRUCTIONS (50-CS03)
9 of 10
STEP 5
Place the Bottom Pieces in the Drawers (15) and insert the Drawers into the side stand.
Attach the Metal Lip (17) to the front of the desktop
with two Screws (J) using the predrilled holes.
STEP 6
Attach Stool Leg A (19) then Stool Leg B (20) to the Stool Cushion (18) with four Screws (F).
Align the Round Support Frame (21) with the holes in the legs. Insert four Screws (E) from the inside and four Nuts (G)
from the outside and fasten them together.
K
Jx2
15
17
J
J
20
19
F
Fx4
18
E=4
G=4
21
G
G
E
•
•
•
10 OF 10
DO NOT stand on the desk. Do not use the desk as a stepladder.
ed.
Every 6 months, check all bolts and screws to ensure they are tight.
Comfort Products, Inc.
P.O. Box 999
Memphis, TN 38101
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products’ authorized dealers
as shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of
parts at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts
to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is
performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or
disassembly; defects occurring after purchase due to product mo
sure
to the elements; labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort
Products be liable in either tort or contract for any loss or direct, special, incidental, consequential or exemplary damages. This Limited
Warranty is NOT applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies only to end-user
customers in the United States. All warranties are limited to the original purchaser for normal use. The weight capacity of the desktop is
130 pounds, the weight capacity of the drawers is 10 pounds, and the weight capacity of the stool is 150 lbs. For claims or questions
concerning this warranty, please visit: www.comfortproducts.net or email us at: [email protected]
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION
www.comfortproducts.net
[email protected]
OneSpace is a Trademark of Comfort Products, Inc.
™
MODEL: 50-CS03
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

OneSpace HMOF User manual

OneSpace
Brand
OneSpace
Model
HMOF
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents