7
ULTRAMODERN GLASS COMPUTER DESK WITH DRAWERS
ASSEMBLY INSTRUCTIONS
MODEL 50-JN1301
SUPPLIER CODE: JNFF
For fastest service on claims, requests for replacement parts,
www.comfortproducts.net/support
e-mail: customerservice@comfortproducts.net
Keep your sales receipt as documentation of your ownership.
CUSTOMER SERVICE
or questions, please visit our website at:
OneSpace is a Trademark of Comfort Products, Inc.
™
mumixam pote l ba T
weight capacity
=
66lbs
mumixam
rewar D
weight capacity
=
sbl 2 2
ASSEMBLY OVERVIEW (50-JN1301)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
2 of 13
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST 1 OF 2 (50-JN1301)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
#
DESCRIPTION
STOCK #
QTY.
1 Leg 51-JN1301LG 2
2
Foot
51-JN1301FT 4
3 Support Board 51-JN1301SB 1
4
Left Board 51-JN1301LB 1
5
Right Board 51-JN1301RB 1
6
Middle Board 51-JN1301MB
1
7 Bottom Board 51-JN1301BM 1
8 Back Board 51-JN1301BB 1
10 Crossbar
51-JN1301CR
2
3 of 13
9a
Outer Rollers
51-JN1301DS
2 sets
of 4
9b Inner Rollers
Left Right
Left Right
ITEMS ARE NOT SHOWN TO SCALE.
PARTS LIST 2 OF 2 (50-JN1301)
# DESCRIPTION SIDE 1 SIDE 2 STOCK # QTY.
#
DESCRIPTION
STOCK #
QTY.
11 Desktop 51-JN1301DT 1
12
Glass Side Panel
51-JN1301SP 2
13 Drawer Back 51-JN1301DB 2
14
Drawer Left
Panel
51-JN1301DL 2
15
Drawer Right
Panel
51-JN1301DR 2
16
Drawer Front 51-JN1301DF
2
17 Drawer Bottom 51-JN1301DBM 2
4 of 13
5 of 13
EXTRA HARDWARE INCLUDED FOR YOUR CONVENIENCE. ITEMS ARE NOT SHOWN TO SCALE.
HARDWARE LIST (50-JN1301)
PART DESCRIPTION
QT
Y.
A M6 X 70MM
4
G
M6 X 45MM 2
K
M4 X 18MM 4
L
M4 X 35MM 8
C 21
IF YOU ARE MISSING ANY OF THESE PARTS,
OR IF YOU HAVE A DAMAGED PART, PLEASE
VISIT WWW.COMFORTPRODUCTS.NET/SUPPORT
REFERENCE THE MODEL # ON THE FRONT OF
THIS MANUAL. SIMPLY COMPLETE THE INFORMATION,
INCLUDING THE PART YOU NEED. THE PART WILL
NORMALLY BE SHIPPED WITHIN 48 HOURS.
- READ THE INSTRUCTION MANUAL BEFORE ASSEMBLING.
- REMOVE ALL PIECES BEFORE BEGINNING INSTALLATION.
- OPEN THE HARDWARE AS NEEDED .
- ASSEMBLE IN AN AREA WITH PLENTY OF SPACE.
- READ EACH STEP BEFORE BEGINNING CONSTRUCTION.
- HAVE A SCREWDRIVER BEFORE YOU BEGIN ASSEMBLING
(NOT INCLUDED).
- NEVER FORCE THE SCREWS OR FITTINGS.
- KEEP THIS MANUAL FOR FUTURE REFERENCE.
- TIGHTEN ALL THE SCREWS EVERY 6 MONTHS.
CLEANING AND CARE
- CLEAN SURFACES WITH A DRY OR DAMP CLOTH.
- DO NOT USE ABRASIVE CLEANERS.
- DO NOT USE A POWER DRILL.
HARDWARE KIT
STOCK # 51-JN1301HA
D
M
N
Cam
Drawer Handle
Allen Wrench
21
B Dowel
6
E M4 x 14MM
16
F M6 x 30MM
8
H M6 x 25MM
4
I M4 x 14MM
4
J Cap & Washers
4
1
2
Extra Hardware (A - L) 1 set
ASSEMBLY INSTRUCTIONS (50-JN1301)
6 of 13
STEP 1
Attach the feet (2) to the bottom of the legs (1).
STEP 2
Attach the legs to the support board (3) with four screws (A), tightening with the Allen wrench (N).
A
A
A x 4
N
ASSEMBLY INSTRUCTIONS (50-JN1301)
7 of 13
STEP 3
Screw six Minix Bolts (C) into the corner holes of the Bottom Board (7) and insert the six Dowels (B) into the
middle holes.
STEP 4
Place six Cams (D) into the lower holes of the Left Board (4), Right Board (5), and Middle Board (6). Note the
arrow on the face of each Cam. It should be pointing toward the nearest edge of the board where the
Minix Bolt (C) will go in.
Before attaching the Left, Right, and Middle Boards to the Bottom Board (7), make sure the unused Cam holes
are all positioned on the same side. Then, align the boards with the six Minix Bolts (C) and six Dowels (B) and
push them down until tight. Tighten the six Cams (D) clockwise half a turn to lock the boards into place.
B x 6
D x 6
C x 6
4
6
7
7
5
The unused holes should be
on the same side.
CAUTION:
Do not overtighten
cams.
C
D
ASSEMBLY INSTRUCTIONS (50-JN1301)
8 of 13
STEP 5
Screw seven Minix Bolts (C) into the Back Board (8).
Place seven Cams (D) in the remaining holes of the boards
assembled in Step 4. Attach the Back Board (8) by aligning the Minix Bolts (B) with the holes. Tighten the
Cams clockwise half a turn to lock the boards into place.
STEP 6
Attach two Right Outer Rollers (9a) to the Right Board (5) and Middle Board (6) using four screws (E). Refer to the
drawing below for which holes in the rollers to use.
C x 7
E x 4
D x 7
CAUTION:
Do not overtighten
cams.
C
D
9a RIGHT
ASSEMBLY INSTRUCTIONS (50-JN1301)
9 of 13
STEP 7
Attach two Left Outer Rollers (9a) to the Left Board (4) and Middle Board (6) using four screws (E). Refer to the
used for the right roller.
Attach two Crossbars (10) to the Left, Middle, and Right Boards using four Screws (F) at the ends and
two Screws (G) in the middle.
STEP 8
E x 4
F x 4
F
F
G x 2
G
10
9a LEFT
N
ASSEMBLY INSTRUCTIONS (50-JN1301)
10 of 13
STEP 9
Attach the legs to the Bottom Board (7)
using four Screws (F).
Attach the glass Desktop (11) to the Crossbars
using four Screws (H).
STEP 10
F x 4
H x 4
10
N
N
ASSEMBLY INSTRUCTIONS (50-JN1301)
11 of 13
STEP 11
Attach the Glass Side Panels (12) to the desk using four Screws (I) with the Caps and Washers (J).
Attach the Drawer Back (13) to the Drawer Left
Panel (14) and Right Panel (15) with four Screws (K),
making sure the grooves are aligned. Slide the
Drawer Bottom (17) into the grooves. Repeat this
step for the second drawer.
Attach four Bolts (C) to the Drawer Front (16). Attach
the Drawer Handle (M) to the Drawer Front with two
Screws (L). Repeat for the second drawer.
STEP 12 STEP 13
I x 4
J x 4
K x 8
L
M
J
I
17
14
16
16
15
13
12
12
C x 8
L x 4
M x 2
ASSEMBLY INSTRUCTIONS (50-JN1301)
STEP 14
Insert four Cams (D) into the holes of the Drawer Left Panel (14) and Right Panel (15). Attach the Drawer Front (16)
to the Left and Right Panels, making sure the groove is aligned with the Drawer Bottom (17). Tighten the Cams
clockwise half a turn. Repeat this step for the second drawer.
STEP 15
Flip the assembled drawer upside down and attach a Right Inner Roller (9b) and a Left Inner Roller (9b) using
four Screws (E) as shown. Refer to the drawing below for which holes in the roller to use. Repeat this step for
the second drawer. Insert the drawers into the desk by aligning the inner and outer rollers.
14
15
16
17
CAUTION:
Do not overtighten
cams.
C
D
D x 8
9b RIGHT
9b RIGHT
9b LEFT
9b LEFT
A
A
E x 8
12 of 13
•
•
•
•
13 OF 13
DO NOT stand on the desk. Do not use the desk as a stepladder.
ed.
Every 6 months, check all bolts and screws to ensure they are tight.
This product is California 93120 Compliant for Formaldehyde.
Comfort Products, Inc.
P.O. Box 999
Memphis, TN 38101
Comfort Products warrants this product to be free from defects in material and workmanship for one (1) year. This warranty is made by
Comfort Products only to the original end-user customer acquiring the product directly from Comfort Products’ authorized dealers
as shown by the original sales receipt. The end-user customer remedy pursuant to this warranty is limited to repair or replacement of
parts at Comfort Products’ option within a reasonable amount of time. Comfort Products reserves the right to require damaged parts
to be returned to Comfort Products upon request. Consent from Comfort Products must be obtained before any warranty work is
performed. This warranty applies under conditions of normal use and is not subject to defects caused by improper assembly or
disassembly; defects occurring after purchase due to product mo
sure
to the elements; labor or assembly cost. This warranty does not cover the cost of transportation or labor. In no event shall Comfort
Products be liable in either tort or contract for any loss or direct, special, incidental, consequential or exemplary damages. This Limited
Warranty is NOT applicable to end-user customers who use Comfort Products for rental purposes. This warranty applies only to end-user
customers in the United States. All warranties are limited to the original purchaser for normal use. The weight capacity of the desktop is
66 pounds and the weight capacity of the drawers is 22 pounds. For claims or questions concerning this warranty, please visit:
www.comfortproducts.net or email us at: [email protected]
PLEASE VISIT WWW.COMFORTPRODUCTS.NET FOR WARRANTY INFORMATION
www.comfortproducts.net
OneSpace is a Trademark of Comfort Products, Inc.
™
MODEL: 50-JN1301
/
