Hammer Drill
Masonry Drill Bit Set
Drop-in Anchor
Setting Tool
Hammer
Pencil
Allen Wrench Set
Wire Brush
Level
Safety Glasses
TOOLS NEEDED: HARDWARE NEEDED:
Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
FOOT MOUNTS:
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Use the drop-in anchor setting tool and hammer to x the anchor into the
drilled hole by inserting the narrow end of the tool into the anchor and giving
it several hammer blows.
Insert one drop-in anchor into the hole and use a hammer to tap the anchor
ush with the concrete.
Repeat steps 2 - 5 until all anchors are installed.
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
5
42
5
AA
63.50
16.00
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay 5 1/2' THM/RPL Flat Bench
001
SHEET 1 OF 1
1:12
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA90T-R
AA
63.50
15.61
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay 5 1/2' THM/RPL Contour Bench with
Armrests
001
SHEET 1 OF 1
1:12
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA80T-R
AA
47.75
16.00
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay 4' THM/RPL Dining Bench
001
SHEET 1 OF 1
1:8
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA48T-R
AA
57.00
29.23
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay 6' THM/RPL Rectangular Table
001
SHEET 1 OF 1
1:12
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA72T-R
AA
1.50
19.02
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay Aluminum Bike Rack
001
SHEET 1 OF 1
1:5
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA30
AA
27.00
15.00
SECTION A-A
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Relay 45 Gallon THM/RPL Trash Receptacle with
Bonnet Top
001
SHEET 1 OF 1
1:10
4/11/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
RLA45T-R
RLA30
RLA45T-R
RLA90T-R RLA80T-R
RLA48T-R RLA72T-R
Copyright 2023 ANOVA®
(4) 1/4"-20 x 1 3/8"
SS Hex Flat Head
92210A545
(4) 1/4"-20
97083A290
Align the mounting holes of the Vibe product over top of the anchors.
It is recommended that you start holes in sequential order from the smaller
to the larger drill bits to avoid oversized holes or holes drilled too deep. Begin
with 5/16" diameter drill bit followed by the 3/8" diameter bit.
!
Care should be given to avoid rubbing the powder coating o the foot. A
rubber washer is a suitable replacement option. Mount the Vibe product
to the anchors by fastening a button head cap screw and washer into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the Vibe product is level before tightening the anchors. Tighten all
of the hardware with a Allen wrench.
!
Place Vibe product in the desired location. Mark the location of the holes with
a pencil. To verify the alignment of the anchor markings you may reference
page 3.
Vibe Collection
Contact Us:
800.231.1327
T/R = Thermory or Recycled Plastic Planks
RLA30 - Vibe Bike Rack
RLA45T/R - Vibe 45 Gallon Receptacle
RLA48T/R - Vibe 4' DiningBench
RLA80T/R - Vibe 5 1/2' Contour Bench
RLA90T/R - Vibe 5 1/2' Flat Bench
RLA72T/R - Vibe 6' Rectangular Table
Installation Instructions
Vibe Collection
RLA80T RLA30 RLA90T RLA45T
4/17/2023
Vibe Collection
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova AE2694LF Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Rotorlight Anova User manual
-
SportsPlay Early Years Bench Installation guide
-
Detecto 6570 Service User manual
-
-
BoMetals QK35 Installation guide
-
Amico 3-23-000607 Installation guide
-
-
-
Enardo 860 and 960 Series Spring-Loaded Pressure/Vacuum Relief Valve Owner's manual
-
Gibraltar Building Products 13193 Operating instructions
