2. Infineon
  3. KIT_T2G-B-H_LITE

Infineon KIT_T2G-B-H_LITE Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Infineon KIT_T2G-B-H_LITE Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
-
QUICK START GUIDE
TRAVEOTM T2G Body High Lite Kit
KIT_T2G-B-H_LITE
Kit contents
1. KIT_T2G-B-H_LITE REV 01 board
www.infineon.com/traveobhlitekit
Quick Start Guide Page 2 of 4
1Power up the kit
Before you start
1. Ensure that you have the following:
– PC with USB Port
– UART terminal soware such as Tera Term
or Minicom
Powering up the kit
1. Connect the USB micro-B cable to J2 and other end to PC
Run the pre-programmed code example
1. Open the UART terminal soware and connect to the kit’s
USB-to-UART COM port with the following settings:
– Baud rate: 115200, Data: 8 bit, Parity: none
– Stop bit: 1 bit, Flow control: none
2. Press the RESET button (SW2) on the kit.
3. The states of various interface tests will be displayed on
the serial terminal as shown.
4. The User LEDs LED3, LED4, LED5 will blink continuously.
Next steps
Visit the kit webpage for required soware, information
on code examples supported for this kit and
kit documentation
Note:
The contents on the serial terminal may vary because
of continuous improvements.
2 Run the shipping firmware
Quick Start Guide Page 3 of 4
TRAVEOTM T2G Body High Lite Kit Board details
1 Shield2Go connectors (not mounted) (J7, J19)
2 mikroBUS connectors (J11, J12)
3 32.768-kHz oscillator for WCO (Y1)
4 16-MHz oscillator for ECO (Y2)
5 Ethernet physical layer (PHY) transceiver (U11)
6 RJ45 Ethernet connector (J6)
7 TRAVEO™ T2G microcontroller (U6)
8 8-pin Arduino header (J13)
9 Expansion header 1 (X1)
10 6-pin Arduino header (J15)
11 DC power jack (J1)
12 Input power supply selection jumper
(J25) - default closed (1-2)
13 Power LED (LED2)
14 KitProg3 USB micro-B connector (J2)
15 VDD current measurement jumper (J20)
16 5V Supply Enable jumper (J22) - default closed
17 MIPI10/20 debug connector (J4)
18 KitProg3 status LED (LED1)
19 PSoC™ 5LP based KitProg3 (U4)
20 Mode switch (SW1)
21 VDDIO current measurement jumper (J21)
22 8-pin Arduino header (J14)
23 Potentiometer (VR1)
24 USER LED (LED)
25 USER LED2 (LED4)
26 USER LED1 (LED3)
27 Expansion header 2 (X2)
28 10-pin Arduino header (J16)
29 CAN FD transceiver (U8)
30 CAN FD connector (J5)
31 USER2 button (SW4)
32 USER1 button (SW3)
33 RESET button (SW2)
34 25-MHz crystal for Ethernet transceiver (Y3)
1
2
1
3
4 765 8 9 10
11
12
13
14
15
16
17
19
18
20
21
22
23
24
25262728293031
323334
Quick Start Guide Page 4 of 4
KIT_T2G-B-H_LITE Board pinout details
AN
RST
CS
SCK
MISO
MOSI
V
GND
PWM
INT
RX
TX
SCL
SDA
V
GND RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
V
AN
AN
SDA
SCL
GND
V
INT
PWM
Date: 09 / 2023
All rights reserved. © 2023
Infineon Technologies AG
Document number: 002-37238 Rev. *A
For additional details, see the kit guide available on the Infineon kit webpage.
RX
TX
RST
GPIO
CS
CLK
MOSI
MISO
NC
IOREF/V
RST/XRES_L_MCU
V
V
GND_/GND
GND_/GND
VIN
P_/D
P_/D
P_/D
P_/D
P_/D
P_/D
UART_TX/D
UART_RX/D
POT_AOUT/A
ADC_/A
ADC_/A
ADC_/A
ADC_/A
ADC_/A
V
P_
NC
NC
NC
NC
SPI_MOSI
SPI_CSO
SPI_CLK
SPI_MISO
NC
NC
NC
NC
XRES_L_MCU
ADC_
SPI_CS
P_
NC
GND
GND
P_
NC
NC
NC
NC
P_
P_
P_
P_
NC
NC
NC
NC
NC
NC
SPI_CS
SPI_CS
P_
VIN
V
AN
AN
SDA
SCL
GND
V
INT
PWM
V
NC
NC
NC
NC
NC
POT_AOUT
P_
ADC_
ADC_
NC
NC
V
P_
UART_TX
USER_SW
USER_LED
NC
NC
GND
GND
NC
NC
NC
NC
NC
NC
P_
P_
ADC_
ADC_
NC
NC
UART_RX
NC
USER_SW
USER_LED
USER_LED
NC
VIN
(AD/SCL)C_SCL
(AD/SDA)C_SDA
AREF/V
GND_/GND
D/SPI_CLK
D/SPI_MISO
D/SPI_MOSI
D/SPI_CS
D/P_
D/P_
/