Extron electronics VSW 2VGA A User manual

Brand
Extron electronics
Model
VSW 2VGA A
Type
User manual
1
VSW2VGAA • User Guide
The Extron VSW2VGAA is a compact and economical two-input, one-output VGA
switcher with unbalanced stereo audio and 300 MHz (-3 dB) video bandwidth. It
accepts two VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or
HDTV component video inputs. The switcher has two unbalanced stereo audio
inputs and one unbalanced stereo audio output. It also features a buffered local
monitor output for Input 1. A front panel toggle switch, a contact closure controller,
or the autoswitching option can be used for input selection.
This guide contains information about the Extron VSW2VGAA switcher. The
terms “VSW2VGAA” and “switcher” are used interchangeably in this manual.
The Extron VSWIAAP interface, an optional accessory used when several
VSW2VGAA switchers are daisy chained together, is also discussed.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the
FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.
NOTES:
• This unit was tested with shielded I/O cables on the peripheral devices. Shielded cables must be used to ensure
compliance with FCC emissions limits.
• For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related
topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website.
Specifications
Product specifications are available on the Extron website, www.extron.com.
Application Diagram
Up to 10 VSW2VGAA switchers can be daisy chained
together with each switcher input separately fed and
controlled by an optional accessory interface, the VSWIAAP.
Figure 1 is an example of how several such switcher-interface
combinations can be daisy chained together in a boardroom
environment.
By default, all switchers are set to input 2 as the active input.
Therefore, in a daisy chain of switchers the VGA and audio
signals ow from one switcher to input 2 of the next switcher
in the chain. The switchers are daisy chained in this fashion
until the last switcher in the daisy chain outputs to a projector
and audio amplier.
Up to ten switchers can be daisy chained together without
any degradation in picture quality. One power supply powers
up to ve switchers.
COMPUTER
SHOW ME
AUDIO
VSW I AAP
In 1
In 2
Extron pre-made VGA with audio cable assemblies.
Expandable, economical presentation chain for
conference rooms and library study rooms.
Out
In 2
VSW I AAP
VSW 2VGA A
Extron
VSW 2VGA A
VGA Switcher
In 1
Out
In 2
VSW 2VGA A
In 1
Out
VSW 2VGA A
VSW I AAPVSW I AAP
Extron
VSW I AAP
Projector
Projector
Extron
VSW I AAP
Figure 1. Daisy Chaining the Multiple Switchers
1
2
VSW2VGAA • User Guide (Continued)
Features
• Inputs — Video on female 15-pin HD connectors, audio on 3.5 mm stereo mini jacks
• Outputs — Video on female 15-pin HD connectors, audio on 3.5 mm stereo mini jacks
• 300 MHz (-3 dB) RGB video bandwidth
• Compatible with VGA-QXGA and HDTV component video signals
• Buffered loop-through for input one
• ID bits from inputs 1 and 2 are routed to the output
• Auto-input switching — Automatically switches to the highest-numbered input with an active video signal.
• Contact closure remote control
• Front panel toggle switch for input selection
• Through-desk, under-desk, and projector-mountable
• 1U, quarter rack width metal enclosure
• External Extron Everlast power supply included — Provides worldwide power compatibility with high-demonstrated
reliability and low power consumption
• Extron Everlast Power Supply is covered by a 7-year parts and labor warranty
Installation Overview
To install and set up the VSW2VGAA for operation, follow these steps:
1. Turn all of the equipment off. Make sure that the video and audio sources (computers, stereos, DVD players, or other
devices), the VSW2VGAA, the output devices (projectors, speakers), and the contact closure control device are all turned off
and disconnected from the power source.
2. If you are going to daisy chain two or more switchers with VSWIAAP control panels, identify the revision of the VSW2VGAA
board (for conguring the VSWIAAPs) and congure the switcher jumpers (see Setting the VSW2VGAA Jumpers on
page4).
3. If desired, mount the switcher (see Mounting the VSW2VGAA on page9).
4. Attach the cables (see Front Panel Features below and Rear Panel Features on the next page).
5. Connect power cords and turn on the devices in the following order: output devices, contact closure controller, VSW2VGAA
switcher, and input devices.
6. Select an input using the front panel input toggle switch or the contact closure controller.
7. The image should now display, and sound should be audible. If not, ensure that all devices are plugged in and receiving
power. Check the cabling and make adjustments as needed. Select a different input to check for a picture and sound.
Front Panel Features
VSW 2VGA A
INPUT 1
2
1
INPUT 2
CC
BB
A
A
DDEEF
F
GG
Figure 2. VSW2VGAA Front Panel Features
A
Input 1 LED indicator — This LED lights green whenever Input 1 (video and audio) is selected.
B
Input 2 LED indicator — This LED lights green whenever Input 2 (video and audio) is selected.
NOTE: The LEDs also serve as power up indicators. When the switcher is powered up, the selected input LED lights.
C
Input select toggle switch — Toggle this switch up to select Input 1. Toggle it down to select Input 2.
D
Input 1 video — Input VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video through
this female 15-pin VGA connector.
2
3
VSW2VGAA • User Guide (Continued)
E
Input 1 audio (see figure2 on the previous page) — Input unbalanced stereo audio through this 3.5 mm mini audio jack (see
figure3).
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 3. Audio Input Connector
F
Input 2 video — Input VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video through
this female 15-pin VGA connector.
G
Input 2 audio— Input unbalanced stereo audio through this 3.5 mm mini audio jack (see figure3).
Rear Panel Features
POWER
12V
.1A MAX
VSW 2VGA A
AUTO-SW
CONTACT
OUTPUT
VGA IN 1 LOOP
1 2
AUD OUT
AA
BBC
CDD EE
Figure 4. VSW2VGAA Rear Panel Features
A
Power connector — Connect the included 12 VDC external power supply to the 2-pole 3.5 mm captive screw connector.
NOTE: One power supply can power up to five switchers (see Power Connnection on page5).
B
Loop Thru Input 1 connector — Female 15-pin HD VGA connector for buffered local monitor output from Input 1
C
Output — Female 15-pin HD VGA connector for output from Input 1 or Input 2. The output video type follows input type and
is either VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video, or HDTV component video.
D
Audio Output connector — Unbalanced stereo audio is output from this 3.5 mm mini audio jack (see figure5).
Sleeve ( )
Ring (R)
Tip (L)
3.5 mm Stereo Plug Connector
(unbalanced)
Figure 5. Audio output connector
NOTE If you are daisy chaining, connect the other end of the audio cable to the Audio input 2 connector on the
downstream video switcher.
E
Contact closure/Autoswitching (Contact/Auto-SW) —
• Contact closure — Connect a contact closure device to this 3.5 mm, 3-pole captive screw connector.
• Pin 1 selects Input 1 when momentarily connected to ground (pin 3).
• Pin 2 selects Input 2 when momentarily connected to ground (pin 3).
• Ground connects to the ground wire (equipment ground).
NOTE: Simultaneously connecting both pins 1 and 2 to ground (pin 3) turns autoswitching mode on.
3
4
5
AUTO-SW
CONTACT
1 2
4
VSW2VGAA • User Guide (Continued)
• Autoswitching —
NOTES:
• Autoswitch mode must be disabled when daisy chaining VSW2VGAA switchers. If the autoswitch mode is
enabled, the switchers cannot be daisy chained.
• RGsB and RsGsBs inputs and outputs occur in manual mode only.
• Autoswitching requires TTL level sync on pin 13 of the 15-pin HD connector.
Pins 1, 2, and Ground when jumpered and shorted together (as shown at right) turn the autoswitching mode on.
When the autoswitching mode is on, the switcher automatically switches to the input that has an active sync
signal.
If both inputs have an active sync signal present, input 2 is selected, and the input 2 LED indicator lights. If no
active sync signal is present, the input 1 LED indicator still lights to indicate that the unit is still powered on.
NOTE: When autoswitch mode is active, both daisy chaining and the front panel input toggle switch are disabled,
and the input cannot be manually switched. Any attempt to toggle the switch while the switcher is in this
mode results in the flashing of the currently active input LED indicator. Contact closure is also disabled while in
autoswitch mode.
Setting the VSW2VGAA Jumpers
NOTE: If you plan to use the VSWIAAP and create a daisy chain configuration, you must configure the switchers before
installing them in a rack or furniture and making connections.
Daisy chaining VSW2VGAA switchers requires you to check, set or both internal jumpers in the switcher.
1. If applicable, disconnect all power to the switcher and any attached devices.
2. Remove the two screws on each side of the switcher (see figure6). Remove the four connector nuts on the front panel of the
switcher. Lift the top cover off of the switcher.
VSW 2VGA A
INPUT 1
2
1
INPUT
2
Remove (4)
Connector Nuts
Remove (4)
Screws
Figure 6. Removing the Cover
3. Set the jumpers for the switcher (see figure7).
4. Set the cover in place and resinstall the screws removed
in step 2.
JMP4
JMP3
JMP5
JMP6
FRONT PANEL
JMP1
EXTRON 20-881-
nn
x
ER:-
yyyyyyyy yyyy
Figure 7. VSW2VGAA Jumper Locations
There are ve jumpers, numbered JMP1, and JMP3 through JMP6, that control daisy chaining on the VSW2VGAA switcher (see
figure7). Both data and power must be daisy chained from one switcher to another.
6
7
AUTO-SW
CONTACT
1 2
5
VSW2VGAA • User Guide (Continued)
OPEN CLOSED
A
ll jumpers are set open (disabled) by default.
opriate settings.
Pin 5 - Show Me Pin 9 - Power
Input 1
Input 2
Output
JMP 1
JMP 4
JMP 6
JMP 3
JMP 5
Figure 8. Jumper Positions
These jumpers enable or disable VGA connector pin 5 (control) and VGA connector pin 9 (power) of the switcher inputs and
outputs.
• Close (install) the jumper for VGA connector pin 5 to daisy chain data to the next switcher.
• Close (install) the jumper for VGA connector pin 9 to daisy chain power to the next switcher (see Using the VSWIAAP on
page6 and Daisy Chain Configuration on page7).
NOTE: When the switchers are not daisy chained together or used with the VSWIAAP, all jumpers should be in the default
(open) position.
Power Connnection
One power supply can power up to ve daisy chained switchers. Additional switchers require one or more power supplies (see
Daisy Chain Configuration on page7).
Figure 9 shows how to wire the power connector.
CAUTION: The DC output cables must be kept separate from each other while the power supply is plugged in. Remove
power before wiring.
ATTENTION : Les câbles de sortie CC doivent être séparés les uns des autres tant que la source d’alimentation est
branchée. Coupez l’alimentation avant d’effectuer tout raccordement.
ATTENTION:
• Do not connect power to the device until you have read the ATTENTION notications on the next page.
• Ne branchez pas l’alimentation à l’appareil avant d’avoir lu les mises en garde « ATTENTION » sur la page suivante.
SECTION A–A
Ridges
Smooth
Power Supply Output Cord
A
A
3/16"
(5 mm) Max.
Figure 9. Wiring the Power Connector
ATTENTION:
• The length of the exposed wires in the stripping process is critical. The ideal length is 3/16 inches (5 mm). Any longer
and the exposed wires may touch, causing a short circuit between them. Any shorter and the wires can be easily pulled
out even if tightly fastened by the captive screws.
• La longueur des câbles exposés est primordiale lorsque l’on entreprend de les dénuder. La longueur idéale est de
5mm (3/16inches). S’ils sont trop longs, les câbles exposés pourraient se toucher et provoquer un court-circuit. S’ils
sont trop courts, ils peuvent être tirés facilement, même s’ils sont correctement serrés par les borniers à vis.
8
9
6
VSW2VGAA • User Guide (Continued)
ATTENTION:
• Always use a power supply supplied by or specied by Extron. Use of an unauthorized power supply voids all
regulatory compliance certication and may cause damage to the supply and the end product.
• Utilisez toujours une source d’alimentation fournie ou recommandée par Extron. L’utilisation d’une source
d’alimentation non autorisée annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi
que l’unité.
• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked
“Class2” or “LPS” rated 12 VDC, 0.5 A minimum.
• Si le produit n’est pas fourni avec une source d’alimentation, il doit être alimenté par une source d’alimentation certiée
UL de classe 2 ou LPS avec une tension nominale de 12 Vcc, 0.5 A minimum.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the power supply and the unit. The
ridges on the side of the cord identify the power cord negative lead (see figure9 on the previous page). To verify the
polarity before connection, plug in the power supply with no load and check the output with a voltmeter.
• La polarité de la source d’alimentation est primordiale. Une polarité incorrecte pourrait endommager la source
d’alimentation et l’unité. Les stries sur le côté du cordon permettent de repérer le pôle négatif du cordon d’alimentation
(voir figure9 sur la page précédente). Pour vérier la polarité avant la connexion, brancher l’alimentation hors charge et
mesurer sa sortie avec un voltmètre.
• To verify the polarity before connection, plug in the power supply with no load and check the output with a voltmeter.
• Pour vérier la polarité avant la connexion, brancher l’alimentation hors charge et mesurer sa sortie avec un voltmètre.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The
power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location,
Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium, or desk.
• Sauf mention contraire, les adaptateurs CA/CC ne conviennent pas à une utilisation dans les espaces d’aération
ou dans les cavités murales. La source d’alimentation doit être placée à proximité de l’équipement Extron dans un
emplacement ordinaire soumis à un degré de pollution de catégorie II, solidement xé au rack d’équipement d’une baie
technique, d’un pupitre, ou d’un bureau.
• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA
70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not be permanently xed to
building structure or similar structure.
• Cette installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité (National
Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie1, section16. La source
d’alimentation ne devra pas être xée de façon permanente à une structure de bâtiment ou à une structure similaire.
NOTE: Do not tin the stripped power supply leads before installing the captive screw connector. Tinned wires are not as
secure in the captive screw connectors and could be pulled out.
NOTE: The maximum number of switchers that can be daisy chained is limited by several factors: power consumption, cable
lengths, and the overall distortion of the video and audio signals.
Operation
Apply power and the input signals. The video and audio output connectors, including the Loop Thru Input 1 connector, should
output signals.
Input Selection
There are three ways to select between Input 1 and Input 2:
• Toggle the front panel input select switch up (Input 1) or down (Input 2).
• Use the rear panel contact closure capability.
• Press the Show Me button on the VSWIAAP to select the input on the connected VSW2VGAA switcher.
Using the VSWIAAP
The VSWIAAP can be used on the inputs of a single switcher or on the inputs of multiple switchers in a daisy chain conguration.
7
VSW2VGAA • User Guide (Continued)
Setting the VSWIAAP jumpers
A jumper on the VSWIAAP may need to be shifted from jumper J6 (the default position) to J5, depending on the application (see
figure10).
J5
J6
Jumper installed
J6
J5
Switcher compatibility
VSW 2VGA A (Input 1)
VSW 2VGA A (Input 2)
Figure 10. VSWIAAP Jumpers
Single switcher example
Figure 11 shows an example of a single switcher conguration.
VSW 2VGA A
Projector
VSW 2VGA A
INPUT 1
2
1
INPUT 2
12
Out
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
Out
Internal Jumper Settings
Jumper
JMP1
JMP3
JMP4
JMP5
JMP6
Setting
Closed
Closed
Closed
Open
Open
12 V Power
Supply
Input 1
Input 2
VSW I AAP
SHOW ME
Figure 11. Single Switcher Configuration
Press the Show Me button on the VSWIAAP to select the corresponding input on the VSW2VGAA.
Daisy Chain Configuration
Multiple VSW2VGAA switchers can be daisy chained together in a loop conguration or a tree conguration.
NOTE: Daisy chaining uses all pins and wires of a standard VGA cable. Not all VGA cables include all pins and wires. Ensure
the VGA cable that you use has all 15 pins connected.
Loop configuration
In a loop conguration, the output of each VSW2VGAA is connected to Input 2 of the next VSW2VGAA switcher. This repetition
of one switcher output to another switcher input can be repeated for up to a maximum of 10 switchers in a daisy chain. The
output of the rst switcher is connected to a display.
Source signals are connected to Input 1 of each VSW2VGAA switcher either directly or through the VSWIAAP interface. Select
the source by toggling to Input 1 on the VSW2VGAA front panel (or through contact closure on the rear panel) or by pressing the
VSWIAAP Show Me button for the corresponding switcher.
• Up to 10 switchers can be daisy chained in this conguration without any signal degradation.
• A power supply is required for every 5 switchers.
• Congure the jumpers on each VSW2VGAA according to the example in figure12 on the next page.
• The VSWIAAP is congured for a loop conguration by default.
10
11
8
VSW2VGAA • User Guide (Continued)
NOTE: In a loop configuration, the Show Me feature can be used without a VSWIAAP control panel. Select Input 1 using
either the front panel toggle switch (see figure2,
C
on page2) or the rear panel contact closure control (see figure4,
E
on page3) to issue the Show Me control signal.
Loop configuration example
Figure 12 shows an example of daisy chaining using a loop conguration.
VSW 2VGA A
INPUT 1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
Projector
VSW 2VGA A VSW 2VGA AVSW 2VGA A
VSW I AAP
2
1
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW 2VGA A
INPUT 1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A VSW 2VGA A
VSW I AAP
2
1
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
12V Power
Supply
VSW 2VGA A
INPUT 1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A VSW 2VGA AVSW 2VGA A
VSW I AAP
2
1
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW 2VGA A
INPUT 1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A
In 1
In 2
Out
In 1
In 2
Out
In 1
In 2
Out
In 1
In 2
Out
In 1
In 2
Out
In 1
Out
In 1
In 2
Out
In 1
In 2
Out
In 1
In 2
Out
In 1
In 2
Out
VSW 2VGA A
VSW I AAP
2
1
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
12V Power
Supply
Jumper Setting
Closed
Closed
Closed
Closed
Closed
Jumper
Setting
Closed
Closed
Closed
Closed
Open
Jumper
JMP1
JMP3
JMP4
JMP5
JMP6
JMP1
JMP3
JMP4
JMP5
JMP6
JMP1
JMP3
JMP4
JMP5
JMP6
Setting
Closed
Closed
Open
Closed
Closed
Ta ble 1Ta ble 2Ta ble 3
1122334455
6
6778899¢¢
Figure 12. Loop Configuration
Tree configuration
In a tree conguration, the output of each VSW2VGAA switcher is connected to Input 1 or Input 2 of the next switcher. This
repetition of one switcher output to another switcher input can be repeated for up to a maximum of 10 switchers in a daisy chain.
The output of the last switcher is connected to a display.
Source signals are connected to Input 1 and Input 2 of each VSW2VGAA switcher at the top of the tree through a VSWIAAP
interface. Select the source by pressing the VSWIAAP Show Me button for the corresponding switcher.
• Switchers can be daisy chained in this conguration up to 10 levels deep without any signal degradation.
• A power supply is required for each switcher in the chain that has its output connected to Input 1 of the next switcher.
• Sources can only be selected and connected to the switcher through the VSWIAAP interface.
• Each VSWIAAP must be congured for the tree conguration (see Using the VSWIAAP on page6 for additional
information).
12
9
VSW2VGAA • User Guide (Continued)
Tree configuration example
Figure 13 shows a simple example of daisy chaining using a tree conguration.
12 V Power
Supply
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A
Projector
Input 1
Out
Input 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
VSW 2VGA A
INPUT 1
2
1
INPUT 2
1234
Out
Out
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
VSW I AAP
VSW I AAP
COMPUTER
AUDIO
SHOW ME
Out
Jumper
Internal Jumper Settings
JMP1
JMP3
JMP4
JMP5
JMP6
Setting
Closed
Closed
Closed
Closed
Closed
Jumper
JMP1
JMP3
JMP4
JMP5
JMP6
Setting
Closed
Closed
Closed
Open
Open
12 V Power
Supply*
Input 1
Input 2
Input 1
Input 2
NOTE: * Every switcher connected
to Input 1 of another switcher
must have its own power supply.
A
AB
B
A
A
B
BBB
Figure 13. Tree Configuration
Mounting the VSW2VGAA
ATTENTION: Installation and service must be performed by authorized personnel only.
ATTENTION : L’installation et l’entretien doivent être effectués uniquement par un électricien qualié.
NOTE: If you are going to daisy chain two or more switchers with VSWIAAP control panels, identify the revision of the
VSW2VGAA board (for configuring the VSWIAAPs) and configure the switcher jumpers before mounting the switchers
(see Setting the VSW2VGAA Jumpers on page4).
The VSW2VGAA can be mounted in a rack, or under or through furniture, using an optional mounting kit available at
www.extron.com. When mounting the switcher, take cabling and power availability into consideration. Follow the appropriate
mounting procedure on the following pages.
Rack Shelf Mounting
UL rack mounting guidelines
The following Underwriters Laboratories (UL) guidelines pertain to the safe installation of the VSW2VGAA in a rack.
1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient temperature. Therefore, install the switcher in an
environment compatible with the maximum ambient temperature (Tma = +122° F, +50° C) specied by Extron.
2. Reduced air flow — Install the equipment in a rack so that the amount of air ow required for safe operation of the
equipment is not compromised.
3. Mechanical loading — Mount the equipment in the rack so that a hazardous condition is not achieved due to uneven
mechanical loading.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the effect that circuit overloading might
have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used
when addressing this concern.
13
10
VSW2VGAA • User Guide (Continued)
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply
connections other than direct connections to the branch circuit (e.g. use of power strips).
Rack mounting instructions
1. If feet were installed on the bottom of the switcher, remove them.
2. Mount the VSW2VGAA on a rack shelf. On the standard rack shelf, the switcher mounts in one of four locations to the rear
of the rack or in one of four locations to the front of the rack.
3. Attach the switcher to the rack shelf using two 4-40 x 3/16 inch machine screws. Insert the screws from the underside of the
shelf and securely fasten them into diagonally opposite corners, as shown in figure14.
1inchQuarterRackShelf
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
RSF 123 Rac
k Shelf
1/4 Rack Width Front
False Faceplate
Figure 14. Mounting the VSW2VGAA on a Rack Shelf
NOTE: Since the switcher is 1.0 inch high, there will be a gap of 0.75 inch above the switcher.
4. Attach the rack shelf to the rack using four 10-32 x 3/4 inch bolts (provided). Insert the bolts through #10 beveled washers,
then through the holes in the rack ears and rack, as shown in figure15.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
1U Universal Rack Shelf
Figure 15. Mounting the VSW2VGAA on a Standard 1U Rack Shelf
14
15
11
VSW2VGAA • User Guide (Continued)
Under-desk mounting
1. Attach the under-desk mounting brackets to the
VSW2VGAA with the four provided machine screws, as
shown in figure16.
2. Hold the switcher with attached brackets against the
mounting surface. Use a soft pencil to mark the location of
holes for screws on the desk or other furniture.
3. Drill 1/4 inch (6.4 mm) deep, 3/32 inch (2 mm) diameter
pilot holes in the table or desk at the marked screw
locations from the underside/inside (concealed side) of the
furniture, where the switcher will be located.
4. Attach the VSW2VGAA to the desk with the provided
wood screws.
Figure 16. Under-desk Mounting Bracket
Through-desk mounting
1. Hold the front panel of the switcher against the furniture.
Use a soft pencil to mark the rough-in opening on the desk.
The opening, 1.125 inch x 4.425 inches (2.8 cm x 11.2 cm)
will be slightly larger than the switcher enclosure.
2. Cut out the material from the rough-in area with a jigsaw.
Check the opening size by inserting the switcher part way
through the hole. If needed, use a saw, le, or sandpaper
to enlarge the hole. Smooth the edges of the hole with
sandpaper.
3. Attach the through-desk mounting brackets to the
VSW2VGAA with the four provided machine screws, as
shown in figure17.
4. Hold the switcher with attached brackets up against the
underside of the desk or table. Use a soft pencil to mark
the locations of the holes for the screws that will attach the
brackets to the desk.
5. Drill 1/4 inch (6 mm) deep, 3/32 inch (2 mm) diameter pilot
holes in the desk or table at the marked screw locations.
The holes should be drilled from the underside or inside
(concealed side) of the furniture, where the switcher will be
located.
VSW
2V
G
A
A
INPU
T 1
2
1
INPU
T 2
Figure 17. Through-desk Mounting
6. Attach the switcher to the desk or table with the provided wood screws, as shown in figure17.
7. To adjust the height of the switcher within the desk, slightly loosen the screws that attach the brackets to the switcher, adjust
the height by sliding the switcher up or down, and retighten the screws.
16
17
VSW2VGAA • User Guide (Continued)
68-1111-01
Rev. E 10 18
© 2007-2018 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Extron electronics VSW 2VGA A User manual

Brand
Extron electronics
Model
VSW 2VGA A
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents