Hampton Bay HB7017P-05 Operating instructions

INSTRUCTIONS MANUAL

HOME DEPOT SKU# 750-734 (UPC# 046335840492)

Page 1

THREE-HEAD POST LANTERN

Page 2

Thank you for purchasing this Hampton Bay Three-Head Post Lantern.

This product has been manufactured with the highest standards of safety

and quality.

1. Handsome Black finish with Bent Beveled glass.

2. Solid cast aluminum resists elements.

3. For energy savings this fixture has been engineered to safely use a

Self Ballasted Compact Fluorescent Lamp in place of an incandescent

lamp.

FEATURES:

Before returning to your local Home Depot, please call our Customer

Service Team at 1-877-527-0313 or visit www.homedepot.com. Please

reference your SKU (750-734) or UPC (046335840492).

QUESTIONS, PROBLEMS, MISSING PARTS:

Page 3

TOOLS REQUIRED FOR INSTALLATION AND ASSEMBLY

(not included):

Safety

goggles

Electrical

tape

Wire

strippers

Wire

cutters

Three Light Bulbs

(100 watt maximum

or CFL equivalent)

Wrench

CAUTION:

1. Before starting installation of this fixture or removal of a previous

fixture, disconnect the power by turning off the circuit breaker or by

removing the fuse at the fuse box.

2. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY

ELECTRICAL QUESTIONS. If you have any non-electrical

questions about this fixture, please call our Customer Service Team at

1-877-527-0313 or visit www.homedepot.com. Please reference your

SKU (750-734) or UPC (046335840492).

3. KEEP your receipt and these Instructions for Proof of Purchase.

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

Page 4

3 ea Hex Screws (#17)

3 ea Arm Assembly (#3)

1 ea Pole (#1)

1 ea Pole (#2)

1 ea Base (#16)

1 ea Top Cover (#12)

1 ea Hood

Finial (#26)

1 ea Hood (#25)

1 ea Hood Bracket (#24)

3 ea Acorn Nuts (#6)

1 ea Wire Housing

(#5)

1 ea Cover

Finial (#14)

3 ea Wire Nuts (#9)

1 Black Extension

Wire (#8)

1 White Extension

Wire (#7)

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture. Lay out all parts on a clean surface.

2. Feed the Wires (#4) of one Arm Assembly (#3) in through one side hole of the

Wire Housing (#5) and through its top opening. Secure each Arm Assembly

(#3) to the Wire Housing (#5) using an Acorn Nut (#6), as shown. (Fig. 1)

3. Unravel the two Extension Wires (#7 & #8). Feed the two Extension Wires

(#7 & #8) into the bottom opening of the Wire Housing (#5) through to the top

opening. (Fig. 2)

4. Using the provided Wire Nuts (#9), make wire connections between the White

Extension Wire (#7) and the White Arm Assembly Wires (#10) and between

the Black Extension Wire (#8) and the Black Arm Assembly Wires (#11), as

shown. Wrap each wire connection with 2” of electrical tape. (Fig. 2)

5. Slide the Top Cover (#12) onto the Threaded Pipe (#13) and onto the Wire

Housing (#5). Thread the Cover Finial (#14) onto the Threaded Pipe (#13) to

secure the Top Cover (#12). (Fig. 2)

6. Unravel and extend the Fixture Ground Wire (#15) of the Wire Housing (#5).

(Fig. 2)

7. Attach Pole (#2) to the Base (#16) using the provided Hex Screws (#17). (Fig.

3)

8. Thread Pole (#1) onto Pole (#2). (Fig. 4)

9. Feed the Wires (#7, #8 & #15) of the Three-Head Lantern Assembly (#19)

through the entire Pole/Base Assembly (#20) to the bottom opening. Screw

the Pole/Base Assembly (#20) into the Wire Housing (#5) of the Three-Head

Lantern Assembly (#19). (Fig. 5 & 6)

Page 5

10. Wrap the Fixture Ground Wire (#15) around the Ground Screw (#21).

Tighten the Ground Screw (#21). (Fig. 6)

11. Proceed to the Installation Instructions.

12. Install an incandescent Light Bulb (#22) or a Listed SBCFL (Self-Ballasted

Compact Fluorescent Lamp [not provided]) into the socket of each Cage

(#23). Do not exceed a 100 watt incandescent light bulb, or a 26 watt

SBCFL. (Fig. 7)

13. Twist a Hood Bracket (#24) into the provided slots of each Cage (#23), as

shown. Slide a Hood (#25) onto each Hood Bracket (#24) and Cage (#23).

Secure each Hood using a Hood Finial (#26). (Fig. 8)

ASSEMBLY INSTRUCTIONS (CONT.):

Page 6

ASSEMBLY:

3. Arm Assembly

Page 7

4. Wires

5. Wire Housing

6. Acorn

Nut

7. White Extension Wire

8. Black Extension Wire

9. Wire

Nut

Fig. 1

Fig. 2

15. Fixture Ground

Wire

12. Top

Cover

14. Cover

Finial

13. Threaded

Pipe

5. Wire

Housing

ASSEMBLY (CONT.):

2. Pole

16. Base

17. Hex

Screws

2. Pole

1. Pole

Fig. 3

Fig. 4

Fig. 5

Wires

19. Three-Head

Lantern

Assembly

Page 8

20. Pole/Base Assembly

5. Wire Housing

ASSEMBLY (CONT.):

Fig. 6

16. Base

15. Fixture

Ground Wire

7. White Extension

Wire

8. Black

Extension Wire

Fig. 7

22. Light Bulb

23. Cage

24. Hood

Bracket

25. Hood

26. Hood

Finial

Fig. 8

23. Cage

21. Ground

Screw

Page 9

Page 10

PARTS INCLUDED FOR INSTALLATION (parts are not to

scale):

INSTALLATION INSTRUCTIONS:

1. Select the desired installation location. Run supply wires from the breaker

panel to the desired location and prepare the concrete surface. (If you are

unfamiliar with proper electrical practices, obtain services of a qualified

electrician.) When preparing the concrete surface, be sure that the Wire

Conduit (#27), protecting the supply wires, extends 1/2” above the Concrete

Surface (#28) to prevent any runoff from entering. Using the provided

Template (#29), mark the locations for the mounting holes. At the marked

locations, drill ½” diameter Holes (#30) approximately 3” deep. Do not

exceed a 3” depth. (Fig. 9)

2. Insert the Anchors (#31) into the Holes (#30). (Fig. 10)

3. Using the provided Wire Nuts (#9), make the following wire connections (Fig.

11):

White Extension Wire (#7) to White (Neutral) Supply Wire (#33)

Black Extension Wire (#8) to Black (Hot) Supply Wire (#34)

Fixture Ground Wire (#15) to Supply Ground Wire (#35)

3 ea Wire Nuts (#9)

3 ea Anchors (#31)

3 ea Flat Washers (#36)

3 ea Lock Washers (#37)

3 ea Hex Nuts (#38)

1 ea Template (#29)

INSTALLATION INSTRUCTIONS (CONT.):

4. Wrap all wire connections with electrical tape for a more secure connection.

Note: If you have electrical questions, consult your local electrical code for

approved grounding methods.

5. Slide the Base (#16) onto the Anchors (#31). (Fig. 12)

6. Slide a Flat Washer (#36) and a Lock Washer (#37) (in that order) onto each

Anchor (#31). Thread a Hex Nut (#38) onto each Anchor (#31) to secure the

Base to the ground. (Fig. 12)

7. Proceed to Step 12 of the Assembly Instructions.

8. Installation is complete. Turn on power at the circuit breaker or fuse box.

Turn the light switch on to activate the fixture.

Page 11

INSTALLATION:

8. Black Extension Wire

34. Black (Hot) Supply Wire

35. Supply Ground Wire

9. Wire Nut

7. White Extension Wire

33. White (Neutral) Supply

Wire

15. Fixture Ground Wire

Fig. 9

27. Wire

Conduit

28. Concrete

Surface

30. Hole

Fig. 10

30. Hole

31. Anchor

Fig. 11

Page 12

Fig. 12

INSTALLATION (CONT.):

16. Base

31. Anchor

36. Anchor

37. Lock Washer

38. Hex Nut

Page 13

Page 14

Possible Cause Corrective Action

1. Power is off. 1. Make sure power supply is on.

2. Faulty switch. 2. Test or replace switch.

3. Faulty wire connection. 3. Check wiring.

Fuse blows or circuit breaker

trips when light is turned on.

1. Crossed wires or power wire is grounding

out.

1. Check wire connections.

Lights will not turn on.

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean

water, never a solvent) to wipe the surface of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the

circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly

dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the

fixture.

3. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft

cloth to dust or wipe carefully.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a

period of three (3) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of of the product at

the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product

that is found to have been improperly installed, set-up, or used in any way not in accordance with the

instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of

an accident, misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating to

faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product,

such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not

warrant and specially disclaims any warranty, whether expressed or implied, of fitness for a

particular purpose, other than the warranty contained herein. The manufacturer specifically

disclaims any liability and shall not be liable for any consequential or incidental loss or damage,

including but not limited to any labor/expense costs involved in the replacement or repair of said

product.

MANUAL DE INSTRUCCIONES

HOME DEPOT SKU# 750-734 (UPC# 046335840492)

Page 15

FAROL DE POSTE CON TRES CABEZAS

Page is loading ...

Fig. 12

INSTALACIÓN (CONTINUACIÓN):

16. Base

31. Taquete

36. Taquete

37. Rondana de presión

38. Tuerca hexagonal

Page 27

Page is loading ...

MODE D’INSTALLATION

HOME DEPOT UGS Nº 750-734 (CUP Nº 046335840492)

Page 29

LAMPADAIRE À TROIS LUMIÈRES

Page is loading ...

Hampton Bay HB7017P-05 Operating instructions

Hampton Bay HB7017P-05 Operating instructions

in other languages

Related papers

Other documents