Anova CAN1824R Installation guide

Brand: Anova

Model: CAN1824R

Type: Installation guide

This manual is also suitable for

Thermory/RPL Seat Cap

(4) 1/4"-20 x 2" Socket Head Screws

Fusion Advantage Seat Cap

(6) 1/4"-20 x 2" Socket Head Screws

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• 3/16" Allen Wrench

or Hex Head Socket

with Extension

Assembly/Installation Instructions

Canyon

CAN1824R - Canyon Recycled Plastic Gabion-Style Stool

CAN1824T - Canyon Thermory Gabion-Style Stool

CAN1824P - Canyon Fusion Advantage Steel Gabion-Style Stool

CAN1872R - Canyon Recycled Plastic Gabion-Style 6' Bench

CAN1872T - Canyon Thermory Gabion-Style 6' Bench

CAN1872P - Canyon Fusion Advantage Steel Gabion-Style 6' Bench

BENCH COMPONENTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

ASSEMBLY:

Inspect the shipping container contents for damage and to determine that all components and hardware are present.1.

2. Lay all parts on a so work surface or on the shipping packaging to prevent damage to the nish.

3. Locate the mesh panels and place them on the work surface as shown.

NOTE: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be applied to the screw threads.

(12) 1/4"-20 x 1"

Socket Head Screws

Thermory/RPL Seat Cap

(16) 1/4" Flat Washers

Fusion Advantage Seat Cap

(18) 1/4" Flat Washers

CAN1872T CAN1872P

(1) 6' or 2'

Thermory or RPL

Seat Cap

(2) End Panels

(2) 6' or 2' Side Panels(1) 6' or 2'

Fusion Advantage

Seat Cap

CAN1824PCAN1824T

(6) Plastic Feet (6) Adhesive Strips

Note: The easiest way to identify the bottom of the panels is by locating the slots, the bottoms of the panels are the only sides with slots.

Also, when applying the adhesive strips to the feet, make sure it is applied to the smooth side of the feet. It will not stick properly to the

rough side.

Apply one piece of the double sided adhesive strip onto the smooth side of a plastic foot. Then place the foot onto on the bottom of one

of the side panels in the center. Repeat this process with the remaining side panel. With the four remaining feet, place two on the outer

edges of each end panel.

Adhesive Strip

Plastic Foot

5. Insert three 1/4"-20 x 1" socket head screws and three 1/4" at

washers through the holes of the end panel and through the

attached nuts on the side panel. Leave screws nger tight.

NOTE: Leave all screws nger tight until all panels are attached

(steps 4 - 6).

6. Attach the other end panel by inserting three 1/4"-20 x 1" socket

head screws and three 1/4" at washers through the holes of the

end panel and through the attached nuts on the side panel. Leave

screws nger tight.

7. Attach the side panel to the assembly by inserting three 1/4"-20 x 1"

socket head screws and three 1/4" at washers through the end panel

and through the attached nuts on the side panel at both ends. Leave

screws nger tight.

8. Secure all screws with a 3/16" allen wrench or hex head socket.

TOOLS NEEDED: HARDWARE NEEDED:

Hammer DrillHammer

Pencil

Wire Brush

Level

Safety Glasses

Masonry Drill Bit Set

3/16", and 3/8"

Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum and be

cured for at least 28 days prior to the installation of the stool.

CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.

Optional: (4) 3/8"

Rubber Washers

90130A050

(4) 3/8" x 3.5" 18-8

Stainless Steel Stud Anchors

92188A202

40"

22.5"

Accept 3/8" mounting hardware

16"

22.5"

Ratchet

Socket Set

9/16"

2' Canyon Stools 6' Canyon Benches

FOOT MOUNTS:

CAUTION: At this point if you plan to anchor the stools or benches, please proceed to Step 8. If you are not

planning to anchor the stools or benches, then please proceed to Step 16.

10.

11.

12.

Evacuate debris from mounting holes using compressed air and a steel

wire brush. This will create a clean environment for the anchor system.

Locate an anchor and adjust the nut so it is ush with the top of the

anchor to protect the threads from being damaged. Insert the anchor

into the hole.

It is recommended that you start holes in sequential order from the

smaller to the larger drill bits to avoid oversized holes or holes drilled too

deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter

bit.

Place stool or bench in the desired location. Mark the location of the

holes with a pencil.

911

Care should be given to avoid rubbing the powder coating o of the

frame or mesh panels. A 3/8" rubber washer is a suitable replacement

option. Mount the stool or bench to the ground by placing a washer and a

nut onto each anchor. Leave the hardware nger tight until all of them have

been installed. Verify that the stool and/or bench is level before tightening

the anchors. Tighten all of the hardware with a ratchet and a 9/16" socket.

16.

14.

15.

Repeat steps 9 - 12 until all anchors are installed.

Remove the nuts and washers o of the anchors. Align the mounting holes of

the stool or bench over top of the anchors and slide it down into place.

16.1

16.2

13. Use the hammer to x the anchor into the drilled hole by giving it several

hammer blows.

17. Care should be given when lling the cage. It is recommended that ller be

hand placed to avoid damaging the cage.

18a. This is a 3-step continuous process. Attach the seat cap by

inserting two 1/4"-20 x 2" socket head screws through two

1/4" at washers; continue threading the screws through

the seat cap frame and through the attached nuts on the

cage assembly at each end of the seat cap.

NOTE: Leave screws nger tight until all screws are placed.

Secure all screws with a 3/16" allen wrench or hex head

socket.

Thermory and Recycled Plastic Lumber Seat Cap Attachment

18b. This is a 3-step continuous process. Attach the seat cap by inserting

six 1/4"-20 x 2" socket head screws through six 1/4" at washers;

continue through the seat cap and through the attached nuts on the

side panels.

NOTE: Leave screws nger tight until all screws are placed. Secure

all screws with a 3/16" allen wrench or hex head socket.

Fusion Advantage Seat Cap Attachment

End Panel End Panel

6' Mesh Side Panel

2' Mesh Side Panel

2' Thermory or RPL Seat Cap

Thermory and RPL

Assembly and Replacement Parts

End Panel

6' Mesh Side Panel

2' Mesh Side Panel

2' Fusion Advantage Seat Cap

Fusion Advantage

Assembly and Replacement Parts

6' Fusion Advantage Seat Cap

6' Thermory or RPL Seat Cap

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

Anova CAN1824R Installation guide

Brand: Anova

Model: CAN1824R

Type: Installation guide

This manual is also suitable for

Download PDF

report

Anova CAN1824R Installation guide

This manual is also suitable for

Anova CAN1824R Installation guide

Related papers

Other documents