Anova BH1801SR Assembly Instruction

Brand: Anova

Model: BH1801SR

Type: Assembly Instruction

This manual is also suitable for

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• Ratchet with 7/16" socket

• Ratchet with 1/2" socket

• 1/2" Open end or box wrench

• #4 Phillips screwdriver

Assembly Instructions

Beacon Hill 2-Seat Bistro Tables w/Contour Swivel Seats

BH1801SR - Recycled Plastic with Contour Swivel Seats

BH1801SR-GT - Recycled Plastic Bistro Game Table, 2 Swivel Seats

BH1801ST - Thermory® with Contour Swivel Seats

BH1801ST-GT - Thermory® Bistro Game Table, 2 Swivel Seats

COMPONENT PARTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

ASSEMBLY:

Thermory® with Contour Seats Recycled Plastic with Contour Seats

Inspect the shipping container contents for damage and to

determine that all components and hardware are present.

2. Lay all parts on a so work surface or on the shipping

packaging to prevent damage to nish.

NOTE: Before assembling the nuts to the bolts, it is

recommended that a light oil or petroleum jelly be applied

to the screw threads.

The assembly is a two-person operation

3. Locate the seat support and place the support on the work

surface upside down with the seat platforms oriented

downward

4. Apply two adhesive strips to one of the plastic rectangular

feet. Then rmly apply the plastic rectangular foot to the

metal foot of the seat support aligning the holes in each.

Repeat for the remaining foot

5. Locate the rubber feet and 1/4”-20 x 1” Phillips head screws.

Insert a screw through the rubber foot into the pre-drilled

hole in the seat support and tighten screws with the #4

Phillips screwdriver. Once all ve rubber feet are installed,

turn the unit over so that the feet are contacting the work

surface.

6. Locate one of the seat swivels. Position the

seat swivel on one of the seat platforms so that

the mounting holes in the seat swivel align

with the mounting holes in the seat platform.

Note: The word “Front” is stamped into the

frame of the swivel. This should be oriented

toward the center of the table assembly.

Insert four 1/4”–20 x 3/4” button head Allen

bolts through the bottom plate of the swivel

and the seat platform mounting plate. Place

1/4” Nylock nuts on the end of the bolts and

nger tighten. Aer all four bolts are installed;

tighten using the 7/16” socket and 5/32” Allen

wrench.

Install the remaining seat swivel in the same

manner.

Note: The bolts must be inside the swivel and

the Nylock nuts must be outside the swivel

for the swivel to work properly

7. Locate one the seat mounts. Position the

seat mount on one of the seat swivel/seat

platforms so that the mounting holes on the

seat mount aligns with the mounting holes on

the top plate of the seat swivel.

Insert four 1/4”–20 x 3/4” button head Allen

bolts through the seat mount and the top plate

of the seat swivel. Place 1/4” Nylock nuts on

the end of the bolts and nger tighten. Aer

all of the bolts are installed, tighten using the

7/16” socket and 5/32” Allen wrench.

Install the remaining seat mount in the same

manner.

Note: The bolts must be inside the swivel and

the Nylock nuts must be outside the swivel

for the swivel to work properly.

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

8. Place one of the seats over one of the seat mounts so

that all the mounting holes line up.

Insert four 5/16”-18 x 1” at head socket cap screws

through the seat mounting holes into corresponding

holes in the seat mount. Place 5/16” at washers and

5/16” Nylock nuts on the end of the screws and nger

tighten. Aer all screws are installed, tighten with a

5/32” Allen wrench and a ratchet with 1/2” socket.

NOTE: Holding the screw still and turning the Nylock

nut protects the nish on the screw and seat from

scratching and chipping during installation.

Install the remaining seat in the same manner

9. Li the tabletop and position it over the tabletop

bracket. Rotate the tabletop until the frame on the

bottom of the tabletop matches the orientation of

the tabletop bracket. Carefully lower the tabletop

down onto the tabletop bracket

Secure the tabletop to the tabletop bracket from the

outside using four 5/16”-18 x 1” hex head bolts, two

on each side with a 5/16” at washer on each of the

bolts. You may have to li the tabletop slightly to

get the holes to align. Place 5/16” at washers and

5/16” Nylock nuts on the end of each bolt inside the

support bracket leaving the bolts nger tight.

Aer all the bolts have been started, tighten with a

1/2” open end or box end wrench and ratchet with a

1/2” socket.

10. Move the table to the location where it will be used.

NOTE: This table is required to be surface mounted

prior to use. Follow surface mount instructions

provided with the surface mount hardware that you

purchase locally.

11. Aer two weeks, retighten all of the hardware.

Anova BH1801SR Assembly Instruction

Brand: Anova

Model: BH1801SR

Type: Assembly Instruction

This manual is also suitable for

Download PDF

report

Anova BH1801SR Assembly Instruction

This manual is also suitable for

Anova BH1801SR Assembly Instruction

Related papers

Other documents