Anova BH1801R-GT Assembly Instruction

Brand: Anova

Model: BH1801R-GT

Type: Assembly Instruction

This manual is also suitable for

anovafurnishings.com

888.535.5005 tel

TOOLS NEEDED:

• Ratchet with 1/2" socket

• 1/2" Open end or box wrench

• 3/16" Allen wrench

• #4 Phillips head screwdriver

Assembly Instructions

Beacon Hill 2-Seat Bistro Tables with Flat or Contour Seats

BH1800R - Recycled Plastic with Flat Seats

BH1800R-GT - Recycled Plastic Game Table, 4 Flat Seats

BH1800T - Thermory® with Flat Seats

BH1800T-GT - Thermory® Bistro Game Table, 2 Flat Seats

BH1801R - Recycled Plastic with Contour Seats

BH1801R-GT - Recycled Plastic Bistro Game Table, 2 Seats

BH1801T - Thermory® with Contour Seats

BH1801T-GT - Thermory® Bistro Game Table, 2 Seats

COMPONENT PARTS:

ASSEMBLY HARDWARE: All hardware is stainless steel.

ASSEMBLY:

Inspect the shipping container contents

for damage and to determine that all

components and hardware are present.

2. Lay all parts on a so work surface or

on the shipping packaging to prevent

damage to nish.

NOTE: Before assembling the nuts to

the bolts, it is recommended that a

light oil or petroleum jelly be applied

to the screw threads.

Thermory w/ Contour Seats Recycled Plastic w/ Flat Seats

Assembly and Replacement Parts

The assembly is a two-person operation

3. Locate the seat support and place the support on the work

surface upside down with the seat platforms oriented

downward

4. Apply two adhesive strips to one of the plastic rectangular

feet. Then rmly apply the plastic rectangular foot to the

metal foot of the seat support aligning the holes in each.

Repeat for the remaining foot.

5. Locate the rubber feet and 1/4”-20 x 1” Phillips head screws.

Insert a screw through the rubber foot into the pre-drilled

hole in the seat support and tighten screw with the #4

Phillips head screwdriver. Once all ve rubber feet are

installed, turn the unit over so that the feet are contacting

the work surface.

7. Place one of the seats over one of the seat mounts so that all the mounting holes line up.

Insert four 5/16” -18 x 1” at head socket cap screws through the seat mounting holes into corresponding holes in the seat mount. Place

5/16” at washers and 5/16” Nylock nuts on the end of the screws and nger tighten. Aer all of the screws are installed, use the 3/16” Allen

wrench to hold the screw head and use the ratchet with 1/2” socket to tighten the Nylock nuts.

NOTE: Holding the screw still and turning the Nylock nut protects the nish on the screw and seat from scratching and chipping during

installation.

Install the remaining seat in the same manner.

6. Locate one of the seat mounts. Position the seat mount on

one of the seat platforms so that the mounting holes in

the seat mount align with the mounting holes in the seat

platform.

Place 5/16” at washers on four 5/16”–18 x 1” hex head bolts

and insert the bolts down through the seat mount and the

seat platform. Place 5/16” at washers and 5/16” Nylock

nuts on the bolts underneath the seat platform. Tighten the

nuts aer all the bolts are installed.

Install the remaining seat mounts in the same manner

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

8. Li the table top and position it over the table top bracket. Rotate the table top until the frame on the bottom of the table top matches the

orientation of the table top bracket. Carefully lower the table top down onto the table top bracket.

Secure the table top to the table top bracket from the outside with 5/16” at washers on four 5/16”-18 x 1” hex head bolts. You may have to

li the table top slightly to get the holes to align. Place a 5/16” at washer and a 5/16” Nylock nut on the end of each bolt at the inside of

the support bracket leaving the bolts nger tight.

Aer all the bolts are started, tighten using a 1/2” open end or box end wrench and ratchet with the 1/2” socket.

9. Move the table to the location where it will be used.

NOTE: This table is required to be surface mounted prior to use. Follow surface mount instructions provided with the surface mount

hardware that you purchase locally

10. Aer two weeks, retighten all of the hardware.

Anova BH1801R-GT Assembly Instruction

Brand: Anova

Model: BH1801R-GT

Type: Assembly Instruction

This manual is also suitable for

Download PDF

report

Anova BH1801R-GT Assembly Instruction

This manual is also suitable for

Anova BH1801R-GT Assembly Instruction

Related papers

Other documents