Welch Allyn Atlas ULTIMOUNT Installation guide

Brand
Welch Allyn
Model
Atlas ULTIMOUNT
Category
Flat panel accessories
Type
Installation guide

Welch Allyn Atlas ULTIMOUNT

The Welch Allyn Atlas ULTIMOUNT is a wall-mounted system designed to securely hold and position medical equipment, such as the Welch Allyn Atlas monitor. It is engineered to provide flexibility and ease of use in healthcare settings.

Key Features:

  • Sturdy Construction: The ULTIMOUNT system is made of durable materials and is designed to withstand a maximum load of 33 pounds.
  • Adjustable Mounting: The arm and basket can be easily adjusted to accommodate different equipment sizes and viewing angles.
  • Locking Pins: Locking pins ensure that the arm and basket remain securely in place, preventing accidental movement.

Welch Allyn Atlas ULTIMOUNT

The Welch Allyn Atlas ULTIMOUNT is a wall-mounted system designed to securely hold and position medical equipment, such as the Welch Allyn Atlas monitor. It is engineered to provide flexibility and ease of use in healthcare settings.

Key Features:

  • Sturdy Construction: The ULTIMOUNT system is made of durable materials and is designed to withstand a maximum load of 33 pounds.
  • Adjustable Mounting: The arm and basket can be easily adjusted to accommodate different equipment sizes and viewing angles.
  • Locking Pins: Locking pins ensure that the arm and basket remain securely in place, preventing accidental movement.
WARNING : It is the health facility or other user’s responsibility to assure that the ULTIMOUNT™ wall mounting
system is anchored to a wall securely and consideration must be given to the load that will be placed
upon the wall mount. Each ULTIMOUNT™ is labeled with a maximum load rating of 33 pounds. Do
not exceed this load limit.
WARNING : Welch Allyn, Inc. does not accept responsibility for any installation, nor for damage or injury arising from the
installation in any type of wall regardless of the type of fasteners and technique used.
WARNING : It is the responsibility of the user of the ULTIMOUNT™ wall mount to see that it is securely anchored to the
wall and that the Atlas™ monitor is securely fastened to the wall mount as directed below.
Tools Required: Phillips head Screw Driver 5/32” Hexagon Wrench (provided)
Hardware Included: (1) Mounting Plate (2) #8-32 Pan Head Phillips Screw - 3/8” long
(2) #8-32 Internal Tooth Lockwasher (4) #10-32 Pan Head Phillips Screw - 1/2” long
(4) #10-32 Internal Tooth Lockwasher
Part No. 620426 Rev. A
Atlas
TM
Wall Mount Installation Guide
Using the ULTIMOUNT™ Wall Mounting System
Mounting Plate
Arm Assembly
Tra ck
Basket
Locking Pin
Locking Pin
Track Stop Screws
Track
Hardware
Locking Pin Holes
Installation Instructions
1. ATTACH THE MOUNTING PLATE TO ULTIMOUNT™ ARM
Place the mounting plate onto the arm assembly and secure with the (4) #10-32 internal tooth lockwashers and (4)#10-32 pan head
screws (Figures 1 and 2).
Figure 1 Figure 2
2. ATTACH THE ULTIMOUNT™ TRACK TO THE WALL
To mount the track to the wall, refer to the manufacturer’s instructions (enclosed in the arm/track
packaging box) for your particular wall type. The track must be oriented so that the locking pin
holes are located on the right.
WARNING : If you feel that you are not competent to perform the tasks and safely attach
the track to the wall, we recommend that you find competent assistance.
Welch Allyn, Inc. does not accept any responsibility for the safety or
performance of the installation.
3. INSERT THE ARM AND BASKET INTO THE ULTIMOUNT™ TRACK
Remove bottom track stop screw (refer to figure 3) with hexagon wrench. Insert arm into the
ULTIMOUNT™ track from the bottom. Hold out the locking pin on the arm and slide the arm up
to the top track stop screw.
Insert the basket into the ULTIMOUNT™ track from the bottom. Hold out the locking pin on the
basket and slide the basket up past the stop screw hole. Replace the bottom track stop screw
and hand tighten with the hexagon wrench.
Adjust basket and arm by pulling out the locking pin and sliding to the desired positions.
4. ATTACH THE ATLAS™ MONITOR TO THE MOUNTING PLATE
With the mounting plate level, place the Welch Allyn Atlas monitor onto the mounting plate as shown (figure 4) and align the plastic
tab on the back of the monitor with the slot on the back of the mounting plate (figure 5).
Figure 4 Figure 5
From the back of the unit, place a #8-32 internal tooth lockwasher and a #8-32 PAN HEAD screw (figure 6) into the 2 mounting
holes, secure the Welch Allyn Atlas monitor to the mounting plate (figure 7).
Figure 6 Figure 7
#10-32
Internal Tooth
Lockwasher
#10-32 Pan
Head
Screw
#10-32 Pan
Head Screw
Locking
Pins
Figure 3
Bottom
Stop
Screw
Atlas unit wall
mount tab
Mounting Plate tab
Atlas Monitor
Alignment Tab
Mounting Plate
Alignment Slot
#8-32 Internal
Tooth Lockwasher
#8-32 Pan Head
Screw
#8-32 Pan Head
Screw
  • Page 1 1
  • Page 2 2

Welch Allyn Atlas ULTIMOUNT Installation guide

Brand
Welch Allyn
Model
Atlas ULTIMOUNT
Category
Flat panel accessories
Type
Installation guide

Welch Allyn Atlas ULTIMOUNT

The Welch Allyn Atlas ULTIMOUNT is a wall-mounted system designed to securely hold and position medical equipment, such as the Welch Allyn Atlas monitor. It is engineered to provide flexibility and ease of use in healthcare settings.

Key Features:

  • Sturdy Construction: The ULTIMOUNT system is made of durable materials and is designed to withstand a maximum load of 33 pounds.
  • Adjustable Mounting: The arm and basket can be easily adjusted to accommodate different equipment sizes and viewing angles.
  • Locking Pins: Locking pins ensure that the arm and basket remain securely in place, preventing accidental movement.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents