Marco FRIIA HCS Plus – 110v Installation guide

Type
Installation guide
1
Instruction Manual
Machine P/N: 1000862, 1000863, 1000868, 1000869, 2300268
FRIIA
2
Contents
1. Font Box Contents................................................................................................2
2. Counter Cut-Out.................................................................................................3
3. Installation..........................................................................................................4
No Drip Tray...............................................................................................4
Drip Tray...................................................................................................5
Connecting Hoses......................................................................................6
5. Operating Font...................................................................................................7
4. Cleaning & Maintenance......................................................................................8
Font Box Contents
3 button font (247MM / 305mm height)
FRIIA Font - 3 button HCS (247MM / 305mm height)
Vent Tube FEP 6mm ID x 8mm OD x 500 (2301250)
Hot Water Tube FEP 5/32” ID x 1/4” OD x 500mm (2301251)
Cold Water Tube FEP 6mm ID x 8mm OD x 500mm (2301250)
Instruction Manual FRIIA Font (1900049)
2 button font (247MM / 305mm height)
FRIIA Font - 2 button HC / CS (247MM / 305mm height)
Vent Tube FEP 6mm ID x 8mm OD x 500 (2301250)
Hot Water Tube FEP 5/32” ID x 1/4” OD x 500mm (2301251)
Cold Water Tube FEP 6mm ID x 8mm OD x 500mm (2301250)
Instruction Manual FRIIA Font (1900049)
3
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Counter Cut Out
4
Installation
1. No Drip Tray
100mm
5
Installation
32mm/ 1 ¼”
100mm/ 4”
2. Drip Tray (sold seperately p/n. 2300268)
100mm
The drain outlet to the drip
tray should be plumbed to
waste
6
Connecting Hoses
Hot, Cold, Sparkling - 3 button
Hot, Cold - 2 button
COLDHOT
VENT
POWER
Chiller to boiler
connector
7mm
8mm
HOT
VENT
COLD
POWER
CHILLER TO BOILER
CONNECTION
COLD
7
Connecting Hoses
Cold, Sparkling - 2 button
COLD
POWER
COLD
Change buttons
Hot water (8mm)
leave empty
Cold Water
7mm
Vent
(plug this)
Power
8
Operating Font
1. HOT (safety feature)
PUSH, RELEASE PUSH AND HOLD
2. COLD
PUSH & HOLD
3. SPARKLING
PUSH & HOLD
Red LED means unlocked
9
1. HOT (safety feature)
PUSH, RELEASE PUSH AND HOLD
Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18
t: +353 (0)1 295 2674
f: +353 (0)1 295 3715
e: sales@marco.ie
www.marcobeveragesystems.com
Cleaning & Maintenance
RISK OF SCALDING
Turn off the boiler before cleaning to
prevent accidental triggering of a dispense.
Beware of accidentally operating the font – especially when cleaning
around the push buttons.
The exterior of the font may be cleaned with a damp cloth and a light
detergent.
Do not use abrasive cloths or creams as this will spoil the finish of the
font.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Marco FRIIA HCS Plus – 110v Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI