Marco FRIIA Hands-Free Cold Install Manual

Marco
Brand
Marco
Model
FRIIA Hands-Free Cold
Type
Install Manual

This manual is also suitable for

Marco FRIIA Hands-Free Cold is a font that can be used in various settings to dispense cold beverages. It features a hands-free operation, which is activated by holding your hand 50 to 100mm over the sensor. The font can be installed with or without a drip tray, depending on your needs. It comes with a 6mm ID x 8mm OD x 500mm FEP tube for connecting to a water source. The exterior of the font can be cleaned with a damp cloth and a light detergent, but abrasive cloths or creams should not be used.

Marco FRIIA Hands-Free Cold is a font that can be used in various settings to dispense cold beverages. It features a hands-free operation, which is activated by holding your hand 50 to 100mm over the sensor. The font can be installed with or without a drip tray, depending on your needs. It comes with a 6mm ID x 8mm OD x 500mm FEP tube for connecting to a water source. The exterior of the font can be cleaned with a damp cloth and a light detergent, but abrasive cloths or creams should not be used.

1
Instruction Manual
Machine P/N: 1000857
HANDS FREE FONT
2
Contents
1. Font Box Contents................................................................................................2
2. Counter Cut Out.................................................................................................3
3. Installation..........................................................................................................4
No Drip Tray...............................................................................................4
Drip Tray.....................................................................................................
.
Connecting Hoses......................................................................................6
5. Operating Font...................................................................................................7
4. Cleaning & Maintenance......................................................................................8
Font Box Contents
Part Number Description Qty
1000857 Font Hands Free Marco 1
1900031 Instruction Manual Hands Free Font Marco 1
2301250 Tube FEP 6mm ID x 8mm OD x 500mm 1
Counter Cut Out
• The 100mm /4” cut out is only required for the font with drip tray.
• The font without drip tray require the 32mm / 1 ¼” cut out only.
• Use a 32mm/ 1 ¼” & a 100mm /4” circular hole saw piece to make the holes.
5
3
100mm
/ 4”
32mm
/ 1 ¼”
82.5mm
Scale 1:1
For drip tray only
100mm
NOTE: Check scale of template before cutting. Scale should be 1:1
Counter Cut Out
4
Installation
32mm / 1 ¼”
1. No Drip Tray
5
Installation
32mm/ 1 ¼”
100mm/ 4”
2. Drip Tray (sold seperately p/n. 2300268)
The drain outlet to the
drip tray should be
plumbed to waste
6
Connecting Hoses
COLD
POWER
COLD
Cold Water
Power
7
Operating Font
Hold hand 50 to 100mm over sensor to
activate font
Remove hand to stop flow of water
8
Marco Beverage Systems Limited.
63d Heather Road,
Sandyford Industrial Estate,
Dublin 18
t: +353 (0)1 295 2674
f: +353 (0)1 295 3715
e: sales@marco.ie
www.marcobeveragesystems.com
Cleaning & Maintenance
• Beware of accidentally operating the font – especially when
cleaning it.
• Power down the chiller before cleaning.
• The exterior of the font may be cleaned with a damp cloth
and a light detergent.
• Do not use abrasive cloths or creams as this will spoil the
finish of the font.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Marco FRIIA Hands-Free Cold Install Manual

Marco
Brand
Marco
Model
FRIIA Hands-Free Cold
Type
Install Manual
This manual is also suitable for

Marco FRIIA Hands-Free Cold is a font that can be used in various settings to dispense cold beverages. It features a hands-free operation, which is activated by holding your hand 50 to 100mm over the sensor. The font can be installed with or without a drip tray, depending on your needs. It comes with a 6mm ID x 8mm OD x 500mm FEP tube for connecting to a water source. The exterior of the font can be cleaned with a damp cloth and a light detergent, but abrasive cloths or creams should not be used.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents