Clear-Com FreeSpeak II Quick start guide

FreeSpeak II
Clear-Com
Brand
Clear-Com
Model
FreeSpeak II
Type
Quick start guide

This manual is also suitable for

Clear-Com FreeSpeak II is a wireless intercom system that allows users to communicate with each other hands-free. It features beltpacks with two audio channels, a base station that routes communication, antennas for coverage, and optional antenna splitters. With the ability to connect up to 5 antennas and power cable lengths of up to 650 ft, it provides extensive coverage and flexibility. The default setup includes two wireless party lines, allowing users to communicate with others on the same channel and the headset on the base station.

Clear-Com FreeSpeak II is a wireless intercom system that allows users to communicate with each other hands-free. It features beltpacks with two audio channels, a base station that routes communication, antennas for coverage, and optional antenna splitters. With the ability to connect up to 5 antennas and power cable lengths of up to 650 ft, it provides extensive coverage and flexibility. The default setup includes two wireless party lines, allowing users to communicate with others on the same channel and the headset on the base station.

Page 1 399G106 Rev C 08/07/15
A FreeSpeak II (FS II) system consists of five main elements:
• Wireless beltpacks (FSII-BP-19, FSII-BP-24).
• The Base station (FSII-BASE) that routes communication to and from the beltpacks and
other audio devices.
• Antennas (FSII-TCVR-19, FSII-TCVR-24) that provide coverage zones in which the
beltpacks operate.
• Optional antenna splitters (PD2203) that run up to 5 separate antennas.
• Suitable headsets such as the Clear-Com CC-300-X4.
Connecting the transceiver/antennas to the Base station
To connect the antennas to the Base station:
1) Clear-Com recommends using 4-pair shielded screened cable (CAT-5/5e/6) with RJ45
connectors to connect the antennas to the Base station. Up to 5 antennas can be
connected to each transceiver port using an antenna splitter, or two antennas can be
connected directly to the Base station. The Base station can power cable lengths of up to
650 ft (200m). Powering antennas or splitters individually can increase cable lengths to a
maximum of 3280 ft (1000m). See 3.2.1 Wiring the antennas and splitters in the
User Guide for more information.
2) When the transceiver/antennas are connected, turn on the Base station and wait for it to
boot.
Using the Beltpacks
The system arrives with a default audio set-up and configuration so the system can simply be
wired and powered for basic use. The default set-up has two Wireless Partylines, WPL01 and
WPL02 for beltpack channel A and B respectively. Each channel talks to:
• All the beltpacks on that channel
• The head set on the Base station.
To customize an audio channel configuration please refer to the
FreeSpeak II User Guide.
IEC power
connector
Transceiver/antenna ports
Wired partyline
connectors
Quick
Start
Guide
FreeSpeak II™ Stand alone
Base station system
Quick Start Guide | FreeSpeak II™ stand alone system
Page 2 399G106 Rev C 08/07/15
Enabling registration of beltpacks to the Base station
1) From the Base station menu, go to MAIN MENU ->SYSTEM ->REG ->START. Enable
registration mode has a two minute inactive time-out.
2) On the beltpack to be registered, hold down the menu key for 2 seconds, then enter
SYSTEM CONNECT using the rotary controllers and the C & D keys.
3) Select the system to pair to. The system will be visible (V) and in pairing mode (P).
4) Enter the four digit pairing code for the system using the rotary controllers and the menu
select key (D). The default is 0000.
5) Select an available role from the list displayed on the beltpack.
The beltpack is now paired and ready for operation. To test, press and hold the channel A button
while talking. Others will hear you on channel A.
Copyright © 2015 HME Clear-Com Ltd. All rights reserved.
Battery
Compartment
Rotary control, audio
levels Channel A (also
menu navigation in
menu mode)
On/Off button (3 second
press and hold)
Rotary control,
audio levels
Channel B (also
menu navigation in
menu mode)
Channel A
Talk button
Channel A Call button
(also cancels menu selection
when in menu mode)
Beltpack information
screen (also displays
menu options when in
menu mode
Channel B
Talk button
Channel B Call button
(also menu select when in menu mode)
Menu button (2 second
press and hold)
Reply button
Menu display screen
Menu control. Push to access menu or select
menu item. Turn to scroll through menu items.
  • Page 1 1
  • Page 2 2

Clear-Com FreeSpeak II Quick start guide

FreeSpeak II
Clear-Com
Brand
Clear-Com
Model
FreeSpeak II
Type
Quick start guide
This manual is also suitable for

Clear-Com FreeSpeak II is a wireless intercom system that allows users to communicate with each other hands-free. It features beltpacks with two audio channels, a base station that routes communication, antennas for coverage, and optional antenna splitters. With the ability to connect up to 5 antennas and power cable lengths of up to 650 ft, it provides extensive coverage and flexibility. The default setup includes two wireless party lines, allowing users to communicate with others on the same channel and the headset on the base station.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents