Best Quality Furniture MAD-Q4N User manual

Brand: Best Quality Furniture

Model: MAD-Q4N

Type: User manual

This manual is also suitable for

ASSEMBLY INSTRUCTIONS

NOTE : MUST TIGHTEN SCREWS PERIODICALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.

MODEL : 0245A

MADELYN DRESSER

(BOX 1)

BOX OF DRESSER

(BOX 1)

NO ITEM QTY

DRESSER

1 pc

BUN FOOT

4 pcs

BOTTOM CENTER LEG

(30 x 30 x 125MM)

1 pc

HARDWARE LIST

(BOX 1)

NO ITEM QTY

JCBC Bolt m6x100mm Blk 4

pcs

Spring Washer 1/4" Blk 4

pcs

Flat Washer 1/4"IDx13mmOD Blk 4

pcs

Allen Key m4x110mm With Ball

Blk 1 pc

STEP 1 : Pull the bottom drawer and take out the Bunfoot carton ( B ). Assemble the Bun Foot (B) with JCBC Bolt (1),Spring washer (2),Flatwasher (3)

and securing with Allen Key (4) as shown.

Remark : Turn the Dresser

to upright position as shown.

COMPLETED ASSEMBLY

Leveler Adjuster

Soft Surface

Remove Bottom

Center Leg

Hardware Pack

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.

STEP 2 :

STEP 3 :

NO ITEM Qty

MIRROR

1 PC

(Box 1)

BOX OF MIRROR

NO ITEM Qty

DRESSER

1 PC

MIRROR SUPPORT

2 PCS

NO ITEM Qty

Flat Head Chipboard Screw m4x32mm

Rbw 10 PCS

MODEL:0245A

MADELYN DRESSER & MIRROR

(Box. 2)

BOX OF DRESSER

(Box. 1)

HARDWARE LIST

ASSEMBLY INSTRUCTION

COMPLETED ASSEMBLY

Hole

Mirror line marking

Dresser line marking LEVELER ADJUSTER

MAKE SURE ARROW

FACE TO FACE

Cut of the Raffia String from the back of DRESSER ( B ).

STEP 1 : Place the MIRROR FRAME (A) on the top of DRESSER (B), turn the

MIRROR SUPPORT RAIL (C) upward at the back of DRESSER (B), then

Tighten with CSK SCREW (1).

Tighten the CSK Screw (1) as shown.

Hole

STEP 1 :

ASSEMBLY INSTRUCTIONS

COMPLETED ASSEMBLY

NOTE : MUST TIGHTEN SCREWS PERIODICALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.

MODEL : 0245A

MADELYN NIGHT STAND

(BOX 1)

NO ITEM QTY

NIGHT STAND

1 pc

BUN FOOT

4 pcs

BOX OF NIGHT STAND

(BOX 1)

HARDWARE LIST

(BOX 1)

NO ITEM QTY

JCBC Bolt m6x100mm Blk 4

pcs

Spring Washer 1/4" Blk 4

pcs

Flat Washer 1/4"IDx13mmOD Blk 4

pcs

Allen Key m4x110mm With Ball

Blk 1 pc

Remark : Turn the Night Stand

to upright position as shown.

Pull the bottom drawer and take out the Bunfoot carton ( B ). Assemble the Bun Foot (B) with JCBC Bolt (1),Spring washer (2),Flatwasher (3)

and securing with Allen Key (4) as shown.

Soft Surface

Hardware Pack

ASSEMBLY INSTRUCTIONS

MODEL : 0245A

MADELYN FULL BED (4+4)

No ITEM Qty

AHeadboard 1 pc

BFootboard 1 pc

CHeadboard Leg 2 pcs

DBed Slats 4 pcs

EBed Slats Support 4 pcs

FSide Rail(A)-Left 2 pcs

GSide Rail(B)-Right 2 pcs

HBed Side Rail Leg 2 pcs

STEP 2.1 :

No ITEM Qty

1JCBC M6 x 35mm 12

pcs

2SPRING WASHER 1/4"

Rbw 12

pcs

3Flat Washer 1/4"ID x

13mmOD Blk 12

pcs

4 ALLEN KEY

m4x65mm Blk 1 pc

5 ALLEN KEY

m5x65mm Blk 1 pc

6Flat Head Chipboard Screw

m4x32mm Rbw 16

pcs

STEP 2.2 :

STEP 2.1 :

Attach Side Rail ( F ) & ( G ) to the Bed Side Rail Leg ( H ) as shown using

JCBC BOLT( 1 )with Spring Washer (2),Flat washer (3)and securing with ALLEN KEY ( 4 ) by outside side rail (F) & (G) .

STEP 2.2 :

Hook SET-UP SIDE RAIL TO HEAD BOARD (A) closely and push down to fit. repeat step 2

with other end of rail to hook onto FOOTBOARD (B).

DO NOT FULLY TIGHTEN SCREW

IN THIS STEP BEFORE ALIGN

THE SIDE RAIL AS SHOWN.

SIDE VIEW

ALIGN BEFORE TIGHTEN

FRONT VIEW

GF H

F G

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS. PAGE 1 OF 2

STEP 1.1 :

STEP 1.2 :

BACK VIEW

C C

Right Sticker

Left Sticker

Attach Head Board Leg ( C ) to Head Board ( A ) as shown using JCBC BOLT( 1 )with Spring Washer (2), Flat washer (3)and securing with ALLEN KEY ( 4 ) .

STEP 1.1 :

Fix the other holes with Csk Screw (6) as shown.

STEP 1.2 :

STEP 3 : Tighten the 4 Corner with Allen Key (5).Fix the Bed Slat Support Leg (E ), to Bed Slat (D) as shown . Install the bed slat ( D ) to side

rail ( F ) & ( G ) and tighten with Csk Screw ( 6 ) as per diagram shown. (NOTE: THE SETUP MUST DONE AT THE DECIDED

LOCATION FOR THE BED TO OBTAIN PERFECT STABILITY)

STEP 3.1 :

STEP 3.3 :

leveler

STEP 3.2 :

Push the side rail(F) & (G) meet with wooden

slat(D) and fix the CSK screw (6)

by using the Screw Driver.

STEP 3.4 :

ASSEMBLY INSTRUCTIONS

COMPLETE ASSEMBLY

NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS. PAGE 2 OF 2

leveler

Best Quality Furniture MAD-Q4N User manual

Brand: Best Quality Furniture

Model: MAD-Q4N

Type: User manual

This manual is also suitable for

Download PDF

report

Best Quality Furniture MAD-Q4N User manual

This manual is also suitable for

Best Quality Furniture MAD-Q4N User manual

Related papers

Other documents