NCF 315543 User manual

Brand
NCF
Model
315543
Type
User manual
ASSEMBLY INSTRUCTIONS
B1564-100 PISCES 6/6 EK PANEL BED-HB/FB/RAILS
PARTS LIST
STEP 1.1 : STEP 1.2 :
6
BACK VIEW
C C
8x
RIGHT
LEFT
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
1 OF 2
C
A
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts,
which may have come loose inside the carton during shipment. Identify and count all items and compare with
the parts list and/or hardware list shown.
HARDWARE LIST
4
1
3
4x
Attach Head Board Leg ( C,D ) to Head Board ( A ) as shown using JCBC BOLT( 1 ) with
Flat washer (3)and securing with ALLEN KEY ( 4 ) .
STEP 1.1 :
Fix the other holes with Csk Screw (6) as shown.STEP 1.2 :
No ITEM Qty
1JCBC M6 x 30mm 12 pcs
2JCBC M6 x 50mm 8 pcs
3
Flat Washer 1/4"ID x
19mmOD Blk 12 pcs
4
ALLEN KEY
m4x65mm Blk
(FOR HB LEG) 1 pc
5
ALLEN KEY
m5x65mm Blk
(FOR SIDE RAIL) 1 pc
6
Flat Head Chipboard
Screw m4x32mm Rbw 32 pcs
No ITEM Qty
AHeadboard 1 pc
BFootboard 1 pc
CHeadboard Leg LSF 1 pc
DHeadboard Leg RSF 1 pc
EBed Roll-Out Slats 2 sets
FBed Slats Support 8 pcs
GSide Rail Left 2 pcs
HSide Rail Right 2 pcs
ICenter Slat 2 pcs
JSide Rail Leg 2 pcs
D
NOTE : MUST TIGHTEN SCREWS PERIODCALLY WITH USE SCREW WILL BECOME LOOSE CHECK TIGHTNESS OF ALL SCREW EVERY 6-8 WEEKS.
2 OF 2
STEP 2.1 :
A
HG
J
R
L
Right Sticker
Left Sticker
BG
H
STEP 2.2 :
5
4
1
3
x8
LOOSEN TIGHTEN
STEP 2.1 :
STEP 2.2 :
5
Attach Side Rail ( G ) & ( H ) to the Side Rail Leg ( J ) as shown using JCBC BOLT( 1 )with
Flat washer (3)and securing with ALLEN KEY ( 4 ) by outside side rail (G) & (H) .
Loosen JCBB Bolt at Headboard & Footboard Leg using Allen Key (5) (Do not tighten them before
Hook SET-UPSIDE RAIL TO HEAD BOARD (A) closely and push down to fit and tighten
them accordingly.
Repeat step 2.2 with other end of rail to hook onto FOOTBOARD (B).
DO NOT FULLY TIGHTEN SCREW
IN THIS STEP BEFORE ALIGN
THE SIDE RAIL AS SHOWN.
SIDE VIEW
ALIGN BEFORE TIGHTEN
FRONT VIEW J
H
G
J
G H
J
G
E
6
STEP 3.2 :
Push the side rail(G)&(H)
meet with wooden slat(E)
and fix the CSK Screw(6)
by using the Screw Driver.
F
Leveler
STEP 3.3 :
E
I
F
2
4
STEP 3.1 :
E
I
B
6
STEP 3.4 :
STEP 3.5 :
REMARK:
Push Slat (E) to the end of side rail
and secure with CSK Screw(6)
as shown.
STEP 3 : Fix the Bed Slat Support (F ), to Bed Slat (E) and Center slats (I) tighten with
JCBC Bolt (2) as shown . Install the bed slat ( E ) to side rail ( G ) & ( H ) and tighten with
Csk Screw ( 6 ) as per diagram shown. (NOTE: THE SETUP MUST DONE AT THE DECIDED
LOCATION FOR THE BED TO OBTAIN PERFECT STABILITY)
Repeat step 3 for other set of slats assembly.
H
  • Page 1 1
  • Page 2 2

NCF 315543 User manual

Brand
NCF
Model
315543
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents