Baxter DPC1S Proofer Installation guide

Brand: Baxter

Model: DPC1S Proofer

Type: Installation guide

DPC1S DEHUMIDIFYING

PROOFING CABINET

INSTALLATION INSTRUCTIONS

DPC1S ML-132533

- NOTICE -

This Manual is prepared for the use of trained Hobart Service Technicians and should not

be used by those not properly qualified.

This manual is not intended to be all encompassing. If you have not attended a Hobart Service

School for this product, you should read, in its entirety, the repair procedure you wish to

perform to determine if you have the necessary tools, instruments and skills required to

perform the procedure. Procedures for which you do not have the necessary tools,

instruments and skills should be performed by a trained Hobart Service Technician.

The reproduction, transfer, sale or other use of this manual, without the express written

consent of Hobart, is prohibited.

This manual has been provided to you by ITW Food Equipment Group LLC ("ITW FEG")

without charge and remains the property of ITW FEG, and by accepting this manual you agree

that you will return it to ITW FEG promptly upon its request for such return at any time in the

future.

SERVICE MANUAL

A product of Baxter MFG. Co., Inc 19220 State Route 162 East Orting, WA 98360

F45568 Rev. D (0923)

TABLE OF CONTENTS

SERVICE UPDATES ....................................................................................... 3

SERVICE UPDATES ................................................................................... 3

GENERAL .................................................................................................. 4

INTRODUCTION ....................................................................................... 4

UNPACKING ........................................................................................... 4

LOCATION ............................................................................................. 4

CLEARANCE DIMENSIONS ............................................................................ 4

TOOLS ................................................................................................. 5

BASIC CABINET CONSTRUCTION ..................................................................... 6

WALL CONFIGURATIONS ............................................................................. 6

PREASSEMBLED CABINETS .............................................................................. 8

POSITION CABINET ................................................................................... 8

FLOOR ................................................................................................. 8

FLOOR BRACKETS .................................................................................... 9

ELECTRICAL SUPPLY CONNECTION ................................................................ 10

FINAL CHECKS ....................................................................................... 11

UNASSEMBLED CABINETS .............................................................................. 12

WALL PANEL ......................................................................................... 12

CEILING PANELS ..................................................................................... 12

FLOOR ............................................................................................... 12

FLOOR BRACKETS ................................................................................... 13

AIR DUCT ASSEMBLY ................................................................................ 14

DRAIN ................................................................................................ 16

AIR INTAKE COVER .................................................................................. 17

GUIDE RAIL .......................................................................................... 17

DOOR HANDLE ....................................................................................... 18

DOOR HINGES ....................................................................................... 18

DOOR MAGNET ...................................................................................... 20

DOOR SWEEP ........................................................................................ 20

COMPONENT & JUNCTION BOX ..................................................................... 20

HUMIDITY/TEMPERATURE SENSOR ................................................................. 22

VENT ................................................................................................. 22

WATER SUPPLY LINE CONNECTION ................................................................ 23

TRIM PANELS ........................................................................................ 24

CONTROLLER TO COMPONENT BOX CONNECTION ................................................ 24

ELECTRICAL SUPPLY CONNECTION ................................................................ 26

FINAL CHECKS ....................................................................................... 28

APPENDIX ................................................................................................ 29

APPENDIX 1 - WATER SUPPLY FITTING CONNECTIONS ............................................ 29

APPENDIX 2 - WATER DRAIN SYSTEM FITTING CONNECTIONS .................................... 32

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS

F45568 Rev. D (0923) Page 2 of 35

SERVICE UPDATES

September 2023

• Updated DOOR HINGES.

• Added APPENDIX 1 - Water Supply Fitting

Connections.

• Added APPENDIX 2 - Water Drain System Fitting

Connections.

October 2020

• Updated ELECTRICAL SUPPLY

CONNECTION under PREASSEMBLED

CABINETS.

• Updated ELECTRICAL SUPPLY

CONNECTION under UNASSEMBLED

CABINETS.

March 2020

• Updated TOOLS.

January 2020

• Updated LOCATION.

• Updated AIR DUCT ASSEMBLY.

• Updated DRAIN.

• Updated COMPONENT & JUNCTION BOX.

• Updated WATER SUPPLY LINE

CONNECTION.

June 2019

• Updated ELECTRICAL SUPPLY

CONNECTION under PREASSEMBLED

CABINETS.

• Updated ELECTRICAL SUPPLY

CONNECTION under UNASSEMBLED

CABINETS.

November 2017

• Updated LOCATION.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - SERVICE UPDATES

Page 3 of 35 F45568 Rev. D (0923)

GENERAL

INTRODUCTION

These instructions are for Baxter DPC1S

dehumidifying proofer. The DPC1S 40.5 inch deep

cabinet can be shipped assembled requiring minimal

field assembly. This cabinet can also be shipped

unassembled requiring field assembly. Both shipping

methods will require leveling and connection to

utilities. All utility connections are the responsibility of

the customer. All information, illustrations and

specifications contained in this manual are based on

the latest product information available at the time

indicated on the cover of the manual. Retain these

instructions for future reference.

UNPACKING

Remove crating from cabinet and check for possible

shipping damage. If cabinet is found to be damaged

after un-crating, save packaging material and contact

the carrier within 15 days of delivery. If location has

multiple cabinets, keep serial numbered crates

together. Check contents against packing list with

shipment. Refer to hardware list for identifying

hardware usage.

LOCATION

• Flooring:

Level floor within 1/8" per foot up to 3/4" in

all directions.

NOTE: For units supplied without a cabinet floor, the

equipment is to be installed on flooring materials that

are corrosion resistant and cleanable. Flooring

materials meeting these requirements may include

masonry materials. If a floor drain is located inside the

proofer, any exposed hardware should be constructed

of non-ferrous material.

• Drain connection:

1/2" FNPT (Female National Pipe Thread)

rear or front drain connection at 5" above

finished floor, route to air gap drain.

• Water connection:

Water and waste piping and connections

shall comply with the International Plumbing

Code 2003, International Code Council

(ICC), or to the Uniform Plumbing Code

2003, International Association of Plumbing

and Mechanical Officials (IAPMO).

NOTE: Plumbing connections must comply with

applicable sanitary, safety and plumbing codes and

provide adequate backflow protection to comply with

applicable federal, state and local codes.

• 3/4" MGHT (Male Garden Hose

Thread) water line connection at 95"

above finished floor. Connection to

solenoid requires 3/4" FGHT (Female

Garden Hose Thread); 3/4" FGHT - to

- 1/2" FNPT adaptor is provided.

• 30-80 psi flow.

• Cold water.

• Water Quality:

• Hardness 2-4 GPG. pH 7.0 to 8.0.

• Chloride concentration 0-30ppm.

• Sediment <.5 micron.

• Turbidity <.5NTU.

• Total dissolved solids <400ppm.

• The electrical diagram is located on the cover of

the component box. Cabinets require a single

phase or three phase 208-240 volt electrical

connection. Neutral wire circuitry needed to

provide 110-120 volt for miscellaneous control

components. A separate 110-120 volt line may

be run or a transformer option will be required if

110-120 volt is not available. Consult Bakery

Product Support for 110-120 volt line or

transformer option requirements.

• Single Phase (L1, L2, Neutral, Ground).

• Three Phase (L1, L2, L3, Neutral, Ground).

CLEARANCE DIMENSIONS

Cabinets UL/CSA Listed for 0" clearance for back and

side walls.

A 2" to 4" back clearance is recommended when

plumbing rear drain connection.

Top of cabinet requires a minimum of 24" clearance

for servicing accessibility.

Side wall(s) require a minimum of 1" clearance for

better performance if the DPC1S cabinet is installed

next to an oven.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - GENERAL

F45568 Rev. D (0923) Page 4 of 35

TOOLS

Standard Tools

• Standard set of hand tools.

• VOM with AC current tester.

Special Tools

• Hammer drill 1/2" Grainger No. 3TB72 to drill

holes in floor for anchor bolts.

• 3/8" masonry drill bit to drill holes in floor for

anchor bolts.

• Setting tool Part No. 01-1000V4-73A to set drop-

in anchors in facility floor (no longer supplied

with proofer hardware as of 4/1/2020).

• Tile Trowel (square notch) Grainger No. 5LG06.

• Roller Tool (Laminate J Roller) - for completing

seal of floor trim to wall.

• 7/32" hex socket 3/8" drive Grainger No. 3LB97.

• 5/16" hex key 6" long Grainger No. 4RE58 to lock

cam locks.

• Handheld, digital temperature and humidity

sensor Grainger No. 13G532 Extech SDL500 or

Grainger No. 4FKP4 THWD-5.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - GENERAL

Page 5 of 35 F45568 Rev. D (0923)

BASIC CABINET CONSTRUCTION

Fig. 1

WALL CONFIGURATIONS

The right side wall will always be the solid wall. The

left side wall will contain the proofing system.

DPC1S Cabinet Width = 42.00"

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - GENERAL

F45568 Rev. D (0923) Page 6 of 35

Fig. 2

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - GENERAL

Page 7 of 35 F45568 Rev. D (0923)

PREASSEMBLED CABINETS

Cabinet can be shipped assembled. You may want to remove door(s) prior to maneuvering cabinet into place. Each

cabinet is shipped with the individual parts needed for on-site assembly, along with a packing list. Before installing

cabinet, compare parts to packing list to ensure all parts were received. Wait as long as possible before removing

plastic protective covering from panels. Apply silicone between floor and wall angle or floor and base channel seams.

Leave no voids.

POSITION CABINET

NOTE: If cabinet rear drain is not accessible from the

back when in final location, route the proofer drain

outside of the cabinet to the facility drain before setting

proofer in final location.

1. Position cabinet near the final location.

2. Determine if the drain must be routed out the

back or front of the unit.

NOTE: If the drain is not accessible with the unit in

the final location, install drain prior to moving unit into

final location.

3. Position cabinet in final location and level.

NOTE: If necessary, place shims under walls to level

cabinet.

FLOOR

1. Install rear corner brackets at both rear corners

of cabinet.

NOTE: Place a spot of silicone on back side of

brackets to aid in holding brackets into position.

Fig. 3

2. Install front corner brackets at bottom of door

jambs.

NOTE: Place a spot of silicone on back side of

brackets to aid in holding brackets into position.

Fig. 4

3. (Cabinet No Floor option only) Check walls for

squareness and Install floor angels.

NOTE: Do not use floor angles on cabinets with floor.

Fig. 5

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - PREASSEMBLED

CABINETS

F45568 Rev. D (0923) Page 8 of 35

4. Apply adhesive to bottom of floor and spread

evenly with a trowel. Cover entire floor surface

with adhesive

Fig. 6

5. Place cabinet floor in final position.

NOTE: Position cabinet floor such that side flange is

behind air duct.

Fig. 7

NOTE: Floor brackets may need to be removed to

position the floor in place.

6. Anchor cabinet floor to facility floor.

7. Check cabinet for being level. If necessary, place

shims under cabinet walls to level.

8. Install door jamb mounting brackets to front

cabinet corners and secure to facility floor.

NOTE: If mounting bracket holes do not line up with

clearance holes in floor, drill new clearance holes.

Fig. 8

FLOOR BRACKETS

1. Install floor brackets to cabinet walls.

NOTE: Ensure front and rear corner brackets are in

the gap between cabinet floor and wall.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - PREASSEMBLED

CABINETS

Page 9 of 35 F45568 Rev. D (0923)

Fig. 10

2. Apply silicone to front and rear corner brackets,

and position them at cabinet floor and wall

panels.

NOTE: Use one floor bracket for each side wall and

one for the rear wall.

3. Install door jamb mounting brackets to front

cabinet corners and secure to facility floor.

NOTE: If mounting bracket holes do not line up with

clearance holes in floor, drill new clearance holes.

4. If door removed earlier, install door onto door

hinges.

Fig. 11

5. Install outer floor trim, remove film covering from

double sided tape and seal trim to wall. Use roller

tool to complete seal to wall.

NOTE: Remove outer protective plastic after outer

floor trim is installed.

NOTE: Before installing outer floor trim, clean outer

wall surface with degreaser.

6. Apply silicone to front corner floor trim at top and

bottom seams.

7. Secure front edge of cabinet floor to facility floor.

8. Install air duct assembly onto cabinet.

ELECTRICAL SUPPLY

CONNECTION

Disconnect the electrical power to

the machine and follow lockout /

tagout procedures. There may be

multiple circuits. Be sure all circuits

are disconnected.

1. Connect electrical supply per the wiring diagram

on the component box cover or back side of lower

front trim, ensuring the neutral wire is

connected at terminal #3 on terminal strip

(Fig. 13 , Fig. 14).

Energizing power supply without a neutral

connection could result in damage to circuit

board.

NOTE: Damage resulting from failure to confirm

neutral connection prior to energizing the equipment

will not be covered under warranty.

NOTE: If 208-240 volt electrical supply does not have

a neutral, a step-down transformer can be installed

(see Fig. 12). Step down transformer must be installed

into a leak tight housing supplied by customer.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - PREASSEMBLED

CABINETS

F45568 Rev. D (0923) Page 10 of 35

Fig. 12

Fig. 13

Fig. 14

FINAL CHECKS

1. Remove all remaining protective plastic.

2. Install plug buttons in unused holes i.e. wall and

ceiling panels.

3. Ensure all holes with wiring / tubing through wall

and ceiling panels are filled with silicone.

4. Test for proper operation.

NOTE: The fans of each proofing system will run

continuously for 20 minutes after power has been shut

off at the controller.

5. Calibrate cabinet for temperature and humidity

following instructions supplied.

6. Complete Installation Checklist and distribute

copies per instructions on checklist.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - PREASSEMBLED

CABINETS

Page 11 of 35 F45568 Rev. D (0923)

UNASSEMBLED CABINETS

WALL PANEL

Refer to WALL CONFIGURATIONS for sequence of

wall panel assembly. As walls are added, ensure

panel seals are on opposite sides.

1. Start with left rear corner at final position on

facilities floor.

NOTE: Both rear corner panels should be positioned

with the cam locks at the top.

NOTE: Turn top cam Clockwise and bottom cam

Counter Clockwise to lock.

2. Attach adjacent rear wall panel and left wall panel

to left rear corner and lock in place.

3. Follow WALL CONFIGURATIONS to assemble

remaining panels.

Fig. 15

CEILING PANELS

1. Start with rear ceiling panel with the square vent

hole in it.

2. Position rear ceiling such that vent hole on left

side of unit. Align edges of ceiling panel with rear

wall and lock into place.

Fig. 16

3. Secure rear ceiling panel to side walls with cam

locks.

NOTE: All cam locks on ceiling panels turn clockwise

except cam locks on front corner panels.

4. When placing front ceiling panel lock ceiling

panels together and then lock to side walls.

FLOOR

1. Install rear corner brackets at both rear corners

of cabinet.

NOTE: Place a spot of silicone on back side of

brackets to aid in holding brackets into position.

Fig. 17

2. Install front corner brackets at bottom of door

jambs.

NOTE: Place a spot of silicone on back side of

brackets to aid in holding brackets into position.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

F45568 Rev. D (0923) Page 12 of 35

Fig. 18

3. (Cabinet No Floor option only) Check walls for

squareness and Install floor angles.

NOTE: Do not use floor angles on cabinets with floor.

Fig. 19

4. Apply adhesive to bottom of floor and spread

evenly with a trowel. Cover entire floor surface

with adhesive.

Fig. 20

5. Place cabinet floor in final position.

A. Position left hand side flange of single piece

cabinet floor such that side flange is behind

air duct.

Fig. 21

6. Anchor cabinet floor to facility floor.

7. Check proofer for being level. If necessary, place

shims under cabinet walls to level.

FLOOR BRACKETS

1. Install floor brackets to cabinet walls.

NOTE: Ensure front and rear corner brackets are in

the gap between cabinet floor and wall.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

Page 13 of 35 F45568 Rev. D (0923)

Fig. 23

2. Apply silicone to front and rear corner brackets,

and position them at cabinet floor and wall

panels.

NOTE: Use one floor bracket for each side wall and

one for the rear wall.

3. Install door jamb mounting brackets to front

cabinet corners and secure to facility floor.

NOTE: If mounting bracket holes do not line up with

clearance holes in floor, drill new clearance holes.

4. If door removed earlier, install door onto door

hinges.

Fig. 24

5. Install outer floor trim, remove film covering from

double sided tape and seal trim to wall. Use roller

tool to complete seal to wall.

NOTE: Remove outer protective plastic after outer

floor trim is installed.

NOTE: Before installing outer floor trim, clean outer

wall surface with degreaser.

6. Apply silicone to front corner floor trim at top and

bottom seams.

7. Secure front edge of cabinet floor to facility floor.

8. Install air duct assembly onto cabinet.

AIR DUCT ASSEMBLY

1. Install plug buttons into unused holes that would

be behind air duct assembly.

2. Install grommets into routing holes in ceiling

panel.

NOTE: Insert in top and bottom of ceiling panel.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

F45568 Rev. D (0923) Page 14 of 35

Fig. 25

3. Remove air intake cover from air duct assembly.

4. Install air duct bolts loosely into nutserts in ceiling

panel.

5. Hang air duct assembly onto bolts using key

holes in air duct assembly.

NOTE: Do not fully tighten bolts into ceiling panel.

6. Secure air duct assembly to wall panel (4 places)

and tighten ceiling bolts.

Fig. 26

NOTE: Insulation may need to be cleaned out of holes

so heater wires can be routed through.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

Page 15 of 35 F45568 Rev. D (0923)

Route heater, fan, and high limit lead wires

through appropriate access hole in ceiling. Install

a 40-inch long, 1/4" diameter piece of poly tubing

from spray nozzle, out through an access hole in

ceiling. There will be a grommet around both the

inner and outer skin access holes.

8. Install water line from solenoid to spray nozzle

using shallow radius bends.

Do not kink the water line.

NOTE: After all water lines and wiring are run up

through access holes, fill access holes with silicone to

prevent moisture from escaping the cavity.

NOTE: Fitting on spray nozzle is a self-locking push-

in type.

DRAIN

NOTE: See APPENDIX 2 - Water Drain System

Fitting Connections for detailed push-to-connect

instructions.

1. Remove knock-out from front or back of duct for

drain line, depending on drain line orientation.

2. Install drain tube with elbow from outside of

cabinet through hole in rear or front wall -

depending on location of facilities drain - then

through cover plate (2, Fig. 27) and side of duct.

NOTE: Insulation may need to be cleaned out of wall

hole so drain tube can be routed through.

Fig. 27

3. Connect Push-to-Connect (PTC) coupler (1, Fig.

28) to drain pan tube.

4. Insert 5" tube (2, Fig. 28) into coupler.

5. Attach PTC elbow (3, Fig. 28) to other end of 5"

tube.

6. Connect drain tube with pre-attached elbow (4,

Fig. 28) into PTC elbow.

Fig. 28

NOTE: Drain tube with elbow assembly may need to

be shortened to limit amount of drain line extending

outside the unit.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

F45568 Rev. D (0923) Page 16 of 35

NOTE: Position drain tube and all fittings so that drain

slopes away from duct with a minimum of 1/4" slope

per foot.

7. Tighten all fittings, and check for leaks and

proper draining.

8. Use two metal screws (1, Fig. 27) to secure drain

line with drain cover plate (2, Fig. 27) to side of

air duct.

9. Use silicone to fill the hole in the cabinet where

the drain tube exits.

Fig. 29

AIR INTAKE COVER

1. Install air intake cover onto air duct assembly. Air

intake cover fits over air duct assembly.

2. Secure cover with 16 screws.

Fig. 30

GUIDE RAIL

1. Remove the necessary protective plastic.

2. Install rear guide rail to rear wall.

3. Install left and right guide rail(s) to rear guide rail

and wall(s).

NOTE: Right and left guide rails have slotted holes

for proper fitting.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

Page 17 of 35 F45568 Rev. D (0923)

Fig. 31

Fig. 32

DOOR HANDLE

1. Remove the necessary protective plastic.

2. Install mounting screws through bumper.

3. Attach bumper to inside of door.

4. Using same screws, attach handle to front of

door.

Fig. 33

DOOR HINGES

Failure to follow this updated procedure may cause

irreparable damage to the front corner panels, making

them unusable. Following this procedure will retain the

backer plates within the corners, and not allow them

to possibly separate inside the corners.

NOTE: On double door units, the door with the control

opening will mount to the left side.

NOTE: Use Red High strength thread locker on all

hinge bolts.

NOTE: Torque all hinge bolts to 90 in-lbs or 7½ ft-lbs.

First Time Install Of Hinges

NOTE: Single door units can be hinged from either

corner panel to obtain door swing required.

1. Remove upper hinge bolts from upper and lower

hinge locations in the desired front corner

section.

2. Apply thread locker to both bolts and loosely

secure female halves of hinges to both hinge

locations.

3. Remove both lower hinge bolts from corner.

4. Rotate hinges to a vertical position.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

F45568 Rev. D (0923) Page 18 of 35

Fig. 34

5. Apply thread locker to bolts and reinstall through

hinge.

6. Secure hinges by tightening all 4 hinge bolts.

7. Repeat process, if necessary, for opposite front

corner if the unit has two loading doors.

NOTE: Ensure bushings (Fig. 35) are installed in

female halves of hinges.

Fig. 35

Door Hinge Mounting

1. Remove upper hinge bolts from hinge locations

at top and bottom of door.

2. Apply thread locker to both bolts and loosely

secure male halves of hinges to both hinge

locations.

NOTE: Be sure to position male half of hinge with post

positioned downward (Fig. 36).

3. Remove both lower hinge bolts.

4. Rotate hinges to a vertical position.

5. Apply thread locker to bolts and reinstall through

hinge.

6. Secure hinges by tightening all 4 hinge bolts.

7. Repeat process, if necessary, for other loading

door if the unit has two loading doors.

Fig. 36

8. Remove unused hinging screws provided for

alternate door swing from opposite front corner

panel, and replace with plug buttons provided in

the unit assembly hardware package.

NOTE: Do not stand door up on door seal at any time.

9. Install plug buttons into hex sockets of all flat-

head hinge bolts in loading doors and front corner

panels.

NOTE: If button-head screws were removed from the

loading door to reverse hinging on single door unit, fill

socket in button-head screws with silicone caulk and

wipe smooth.

NOTE: Before installing plug buttons apply a dab of

silicone on back side of plug buttons.

10. Install door onto cabinet.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

Page 19 of 35 F45568 Rev. D (0923)

DOOR MAGNET

1. Install magnet assembly to top of door.

Fig. 37

DOOR SWEEP

1. Remove rubber door sweep from bottom of door

sweep bracket by removing seven nuts & bolts.

Fig. 38

2. Replace rubber door sweep.

3. Evenly align rubber door sweep to bottom of door

sweep bracket.

4. Secure rubber door sweep to bottom of door

sweep bracket using seven nuts and bolts.

NOTE: Holes on door are elongated in order to

properly adjust placement of door sweep.

Fig. 39

COMPONENT & JUNCTION BOX

1. Install the component box assembly to top of

ceiling panel at front of cabinet.

Fig. 40

2. Verify grommets installed into wire holes in

ceiling panel above air duct.

3. Install junction box with self drilling screws.

DPC1S DEHUMIDIFYING PROOFING CABINET INSTALLATION INSTRUCTIONS - UNASSEMBLED CABINETS

F45568 Rev. D (0923) Page 20 of 35

Page is loading ...

Baxter DPC1S Proofer Installation guide

Baxter DPC1S Proofer Installation guide

Baxter DPC1S Proofer Installation guide

Related papers

Other documents