INSTALLATION INSTRUCTIONS
BOXLED MINI
BL716LED
®
Beghelli USA
3810 Executive Way
Miramar, Florida 33025 USA
P: 800 726 4316 / P: 954 442 6600 F:
954 442 6677
www.BeghelliUSA.com
Beghelli Mexico
Av. Del Marqués No. 70, Int. 4
Parque Industrial Bernardo Quintana
C.P. 76246 El Marqués, Qro.
P: +52 442-221-6439 / F: +52 442-221-6215
www.BeghelliMexico.com
MODEL INFORMATION
BOXLED MINI INSTALLATION INSTRUCTIONS
BOXLED MINI (BL716) LED LO/MO/HO
BOXLED MINI
®
®
BL716LED
IP66 IK09 NEMA 4x
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
1. CAUTION! ALWAYS MAKE SURE THE POWER IS TURNED OFF before starting installation.
2. Wiring fixture to power supply, shall be performed by a certified electrician, and wired in a manner that
complies with all local and national electrical codes, as well as the manufacture’s wiring diagram.
SAVE THESE INSTRUCTIONS!
No user serviceable parts. Refer service to a qualified service
technician. Read instruc tion s prio r to installing and/or operating
this device. Installatio n should be performed by a licensed
electrician/inst aller in accordance with local codes .
WATTAGE 20W/30W/40W
120-277V ; 50/60Hz
YES
HT (AC ONLY)/0-10V DIMMING
2.6 lbs
-30°C(-22°F)/40°C(104°F)
7.5” L X 6.8” W X 3” H
VOLTAGE
WET LOCATION
OPERATION
WEIGHT
DIMENSION
AMBIENT TEMPERATURE
®
DIMMING WIRING DIAGRAM
1. 0-10V dimming wires must be run from a different conduit out of the J-box.
NOTE:
- For non-dimming, 3-conductor cord
available (upon request).
0-10V LEAD / DALI
VIOLET......(DIM +)
GRAY........(DIM -)
AC LEADS
BLACK...... (HOT)
WHITE........(NEUTRAL)
GREEN...... (GROUND)
3G
Vibration
Rated
BOXLED MINI INSTALLATION INSTRUCTIONS
SURFACE MOUNT (SM) (STANDARD INSTALLATION)
AVIATION CABLE (AC)
HOOK/CHAIN MOUNT (HK & CH)
Locate, mark, & install anchors for mounting bracket.
Install the fixture as shown (hardware by others).
Attach the glider on the bracket using washer & screw as shown.
Feed the cable through glider by pressing sleeve to release lock.
Attach the clip-hook on the bracket using washers & lock-nut as shown.
1.
2.
1.
2.
1.
120-277V ; 50/60Hz
®
MOUNTING
HARDWARE
(BY OTHERS)
Mounting Bracket Dimensions
INSTALLATION INSTRUCTIONS
Adjust bracket angle by loosening the nut.
Re-tightened once the angle is set.
Attach stem adaptor to bracket using screws
& lock-nuts as shown.
Attach stem to the assembly as shown.
Pass power cord through assembly and stem.
ADJUSTING BRACKET
1.
2.
3.
4.
5.
PENDANT KIT (PK)
BOXLED MINI
®
CONVERTING FROM SYMMETRIC TO ASYMMETRIC
Remove the screws & lift the tabs. Position the asymmetric reflector
as shown.
Insert the tabs through the slots on
the symmetric reflector.
Bend tabs to complete installation
of asymmetric reflector.
Symmetric
Asymmetric
Open the lens to install
the asymmetric reflector.
1. 3.
4. 5.
2
1
2.
3
4 5
bended tabs
/
