Esse-ti e-stant User manual

Alarm system for elevators

compliant with the European Standard

EN 81-28:2018

Software e-stant

USER GUIDE

To download e-stant software

please scan the QR-code or visit www.esse-ti.it

DESCRIPTION

e-stant software allow the programming of Esse-ti’s devices.

 To verify the software and hardware to be used with each model of

alarm system, please see the table at the following page.

e-stant allows:

- to program, locally (via cable) and remotely (via modem or via SMS),

Esse-ti alarm systems

- to generate QR codes containing programming codes to be sent to the

alarm system via SMS

- to read/write all settings of the alarm system

- to test the alarm system's alarms

- to control the log of events occurred to the alarm system

- to reproduce the alarm system’s voice prompt

- to restore or customize the audio messages locally

- to update the firmware locally

- to set a micro SD card to use for programming, customizing the messages

and updating the firmware of the alarm systems

Operating system required: Windows 8.1/10 (32-bit/64-bit)

3

Model Software Hardware

Local

programming

Helpy 2W-4G

Helpy 2W-2G

Helpy 2W-V

Helpy 2W-Q

Helpy 2W-TL

Helpy 2W-LCP

Helpy Compact

Helpy Controller

HelpyGSM

e-stant USB/serial cable

(5IU-001)

Remote

programming

via modem

Helpy 2W-4G

Helpy 2W-2G

Helpy 2W-V

Helpy 2W-Q

Helpy 2W-TL

Helpy 2W-LCP

Helpy Controller

HeControl

+

e-stant

HeGate modem

(5HE-053)

Remote

programming

via SMS

Helpy 2W-4G

Helpy 2W-2G

Helpy 2W-TL*

Helpy 2W-LCP*

Helpy Controller

HelpyGSM

Helpy Air

*:with GSM200-C

e-stant

GSM500 Text (5IG-200)

or

4G.text (5IG-050)

or

mobile phone

or

other device that can

send SMS messages

4

CONNECTION

Connecting the alarm system

 Connect the USB connector of the USB/serial cable 5IU-001 to the USB

port of PC.

 Check the correct presence of a new COM port in the “Ports (COM &

LTP)” item of the Windows “Device Manager”.

 Connect the USB/serial cable to the serial port of the alarm system using

the connector shown in the following table:

Model Serial connector

Helpy 2W-4G

Helpy 2W-2G

Helpy 2W-V

Helpy 2W-Q

Helpy 2W-TL

Helpy 2W-LCP

Helpy Compact

Helpy Controller

B

HelpyGSM A

 Switch on the alarm system.

5

Establishing the connection

 Start the e-stant software.

 Press the

Manage new device

icon on the toolbar or select

New

from the menu

File

.

 Select the desired alarm system and press

OK

.

6

 Select

Direct connection Serial/USB

and press

OK

.

 Select the port COM to which the alarm system is connected and press

OK

.

The programming window of the alarm system will be displayed.

If the alarm system has the default installer password (“0”) the e-stant software

automatically establishes the connection and the Installer password button (top

right) will change colour from blue to green.

If the alarm system’s password is not the default one:

 To establish the connection, in the

Installer password

field enter the

alarm system’s installer password and press

OK

.

The Installer password button will change colour from blue to green.

Disconnecting

At the end of the programming to disconnect from the alarm system:

 Close the window.

7

LOCAL PROGRAMMING

General legend

Programming code buttons:

YES the code can be changed and sent to the alarm system

NO the code cannot be changed and sent

Dark blue the code cannot be changed and sent

Light blue the code has not yet been read

Green the code has been read and the setting in the field is

equivalent to the setting in the alarm system

Orange the code has been read and the setting in the field is

different from the setting in the alarm system

Red it is necessary to enter a setting in the field

Black the code is not present in the connected alarm system.

e-stant buttons:

Smart send it allows to program the alarm system with the settings

entered in the modified fields (fields marked with a light

blue or orange YES button)

Send whole configuration

it allows to program the alarm system with the settings

entered in the fields marked with a YES button

Read configuration of selected parameters

it allows to read the settings of the fields marked with a

YES button

Read whole configuration

it allows to read all the settings of the alarm system.

8

Phonebook legend

Menu:

Event it allows to select the type of alarm or call associated

with the stored number

Mode it allows to select the call forwarding mode

User voice call

(for phones or call centers with manual-call

management)

Esse-ti Esse-ti protocol call

(for call centers using Esse-ti protocol or Esse-ti

management software)

CLI “Calling Line Identifier” call

(call that does not need to be answered, for call centers

with CLI management)

SMS SMS

(for call centers with SMS management)

P100 P100 protocol call

(for call centers using P100 protocol)

9

Examples

Telephone number programming for emergency request

E.g. 001122334455: first telephone number for emergency request

001199887766: second telephone number for emergency request

 Select the position in the “Phonebook” tab where you want to enter the

first phone number for the emergency request by changing the status

from NO to YES.

 Select the type of alarm in the

Event

field:

01- Button alarm

.

 Select the call forwarding mode in the

Mode

field:

02- User

.

 Enter the phone number in the

Number

field:

001122334455

.

 Select the position in the phonebook where you want to enter the

second phone number for the emergency request by changing the

status from NO to YES.

 Select the type of alarm in the

Event

field:

01- Button alarm

.

 Select the call forwarding mode in the

Mode

field:

02- User

.

 Enter the phone number in the

Number

field:

001199887766

.

 Press

Smart send

button to send the entered parameters to the alarm

system (buttons will turn green).

10

Periodic automatic test enabling

E.g. 00111222333: telephone number for periodic automatic test

 Select the position in the “Phonebook” tab where you want to enter the

phone number for the periodic automatic test by changing the status

from NO to YES.

 Select the type of call in the

Event

field:

03- Periodic automatic test

.

 Select the call forwarding mode in the

Mode

field:

04- CLI

.

 Enter the phone number in the

Number

field:

00111222333

.

 Press

Smart send

button to send the entered parameters to the alarm

system (button will turn green).

The programming of the telephone number automatically activates the periodic

automatic test in the “Call” tab.

11

12

Relay setting

E.g. relay 1 activated in case of telephone line failure

 In the “Device” tab enable the relay 1 by changing the status from NO

to YES.

 Select in the

Mode

field:

07- Phone line failure

.

 Set the relay blink mode by changing the status from NO to YES.

 Select

0- Steady

or

1- Blink

.

 Press

Smart send

button to send the entered parameters to the alarm

system (buttons will turn green).

13

Customizing messages

E.g. customize the courtesy message (n° 02)

 Select

Update messages

from the menu

Tools

.

 Press

Specific messages

button and press

OK

.

 Press the button of the message number 02.

 Select the new message to upload and press

Open

.

 Press the button

Write

and wait until the operation is completed.

 Press

OK

to confirm.

14

SD card programming

E.g. set a micro SD card to use for programming and customizing the

messages of the alarm system

 Insert the micro SD card in the reader of PC (or in a reader connected to

the PC).

 Press the

Manage new device

icon on the toolbar or select

New

from the menu

File

.

 Select the desired alarm system and press

OK

.

 Select

Secure Digital

TM

memory card

and press

OK

.

 Select the memory card drive and press

OK

.

 Make the desired programming in each tab and, at the end, press

the

Write configuration

button.

 Press

Yes

to confirm and press

OK

at the end of the configuration’s

writing.

 Select

Update messages

from the menu

Tools

.

 Press

Specific messages

button and press

OK

.

 Press the button of the message you want modify.

 Select the new message to upload and press

Open

.

 Press the button

Write

and wait until the operation is completed.

15

 Press

OK

to confirm.

 Press

Close

to exit.

 For the use of the micro SD card please refer to the Micro SD card Use

procedures.

e-stant

Local programming guide

28/01/2021

Esse-ti e-stant User manual

Esse-ti e-stant User manual

Related papers

Other documents