Vantec UGT-CR960 Installation guide

UGT-CR960
Vantec
Brand
Vantec
Model
UGT-CR960
Category
Card readers
Type
Installation guide

Vantec UGT-CR960 is a multi-memory internal card reader that supports various memory cards and provides connectivity options like USB 2.0, eSATA, and audio ports. It allows easy transfer of data between different memory cards and your computer. The device is compatible with both Windows and Mac operating systems. It includes a 3.5" to 5.25" mounting bracket for flexible installation inside your computer case. Additionally, it features front covers in different colors to match your computer's aesthetics.

Vantec UGT-CR960 is a multi-memory internal card reader that supports various memory cards and provides connectivity options like USB 2.0, eSATA, and audio ports. It allows easy transfer of data between different memory cards and your computer. The device is compatible with both Windows and Mac operating systems. It includes a 3.5" to 5.25" mounting bracket for flexible installation inside your computer case. Additionally, it features front covers in different colors to match your computer's aesthetics.

1
Multi-Memory Internal Card Reader
w/USB2.0, eSATA, Audio Ports
Model No.: UGT-CR960
Installation Guide
v1.02
2
System Requirement
• Microsoft Windows XP/Vista/7(32/64 Bit)
• Mac OS x 10.4+
Package Content
• Vantec Multi-Memory Internal Card Reader w/USB2.0, eSATA, Audio
Ports
• 3.5” to 5.25” Mounting Bracket
• Installation Guide
• Installation Screws
Bracket Installation instructions
Left Right
• Step 1: See above, distinguish metal plates installed for left and right.
3
•Step 2: Install the screws to card reader, both left and right(refer to
above photo)
Step 3: Put the card reader inside the bracket, tighten the screws.
Step 4: Finish
Installation of product
If in doubt about how to install the device correctly, please contact
an EXPERT or a specialist workshop and let them do the
installation! Improper installation can damage the plug-in unit as
well as your computer and all connected devices.
4
Proceed with caution. Danger to
life!
Switch off the computer in which the product is to be installed and
all connected devices. Disconnect all devices from the mains
voltage and pull out the main AC power cord! Just turning off at the
on/off switch is not enough!
• Open your computer’s housing and carefully remove the cover.
• Look for a free 3.5’’ installation slot and remove the slot cover.
Often there is a metal shielding behind it, which has to be
removed first. With some casings, you have to unscrew this, with
others you have to break it out carefully. Depending on the casing,
you may have to remove the entire front cover first.
• Apart from the slot cover that is already mounted on the slot, the
scope of delivery includes two more front covers in different
colours. Depending on the existing computer housing, the slot
cover can easily be replaced by another one.
• Connect the 9-pin USB plugs to an internal USB ports on the
motherboard. It is imperative to observe the correct orientation
(see operating instructions for the motherboard) since a wrong
connection may damage both the motherboard and the
electronics of the 3.5“plug-in unit, loss of warranty (refer to below
photo)!
5
-9pin
USB plug -USB 9pin pinouts
Most motherboard use cable pinout,
some motherboard have slot for fixing
it
• Connect the Audio plug connector with a free Audio connection of
your motherboard. Please also note the operating instructions of the
motherboard.(refer to below photo):
6
-Audio Plug -Audio pinout
• Connect the SATA plug connector with a free SATA connection of
your motherboard. Please also note the operating instructions of the
motherboard. (Refer to below photo)
-Red SATA cable -SATA connector on motherboard
• Install the cables so that they do not protrude into any of
the computer’s fan, use cable ties, for example.
• Close the computer housing.
• Connect your computer and monitor to the mains voltage and
switch on all devices.
7
• If your computer does not start correctly, switch it off again
immediately and check all the settings and cable connections.
It must be disconnected from the mains power supply before
restarting, see above!
8
Warranty:
The Multi-Memory Internal Card Reader w/
USB2.0, eSATA, Audio Ports
comes with a 1 year limited
warranty
.
If
your unit should become
defective within that
time
frame, please go to
http://www.vantecusa.com
for information on
how
to receive
warranty exchange or repair. Cosmetic defects and
missing
parts
are not covered under this warranty. Please check the
contents
of the unit to make sure you received all parts.
Also,
check for
any
cosmetic
flaws. If
any parts are missing or
if
there are cosmetic
defects,
please contact the retailer from which you
purchased
the
unit
immediately and ask for a
replacement.
Contact:
Vantec
T
h
erm
a
l
T
e
c
hno
l
o
g
y
www.vantecusa.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Vantec UGT-CR960 Installation guide

UGT-CR960
Vantec
Brand
Vantec
Model
UGT-CR960
Category
Card readers
Type
Installation guide

Vantec UGT-CR960 is a multi-memory internal card reader that supports various memory cards and provides connectivity options like USB 2.0, eSATA, and audio ports. It allows easy transfer of data between different memory cards and your computer. The device is compatible with both Windows and Mac operating systems. It includes a 3.5" to 5.25" mounting bracket for flexible installation inside your computer case. Additionally, it features front covers in different colors to match your computer's aesthetics.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents