Boston Whaler 130 Super Sport Bucket Sport Seat Installation guide

Boston Whaler
Brand
Boston Whaler
Model
130 Super Sport Bucket Sport Seat
Type
Installation guide
ACCESSORY INSTALLATION
INSTRUCTIONS
Page
1
of 5
BUCKET SPORT SEAT
Installation Instructions for the 130 & 160 Super Sport
Issue Date
06/15/2018
Rev. D
1.
PURPOSE
Provide step-by-step procedure for the bucket sport
seat installation.
2.
SCOPE
This procedure is limited to the bucket sport seat installation on the 130 & 160 Super Sport.
3.
DEFINITIONS
3.1.
Not Applicable
4.
RESPONSIBILITIES
4.1.
Not Applicable
5.
TOOLS/EQUIPMENT REQUIRED
5.1.
Drill
-3/16”drill bit
-Phillips head bit
5.2.
3/8” wrench
5.3.
Pencil
5.4.
Tape Measure
5.5.
Hardware Kit (supplied)
6.
SAFETY
CONTENTS OF KIT PART #
Bucket Sport Seat ..........................................2317045
Warning Label ................................................1971919
Hardware Pkg...............901BWBUCKETSPORTSEAT
6.1.
Follow all established guidelines for the respective area.
7.
FORMS
7.1.
Not applicable
ACCESSORY INSTALLATION
INSTRUCTIONS
Page
2
of 5
BUCKET SPORT SEAT
Installation Instructions for the 130 & 160 Super Sport
Issue Date
06/15/2018
Rev. D
8.
PROCEDURE
8.1.
Using the measuring tape, measure inboard
12” (13SPT) 14.5” (16SPT) from the starboard
forward edge of the bench seat.
8.2.
Using the pencil, mark a vertical line on the
forward edge of the bench.
8.3.
Using the pencil, mark a horizontal line 1” down from
the surface of the bench seat.
8.4.
Measure up 3/8” from the mark made in the previous step
and draw a horizontal line intersecting the vertical line made
in step 8.2.
ACCESSORY INSTALLATION
INSTRUCTIONS
Page
3
of 5
BUCKET SPORT SEAT
Installation Instructions for the 130 & 160 Super Sport
Issue Date
06/15/2018
Rev. D
8.5.
Using the 3/16” drill bit, drill through the bench seat at the
point where the lines made in steps 8.2. & 8.3 intersect.
8.6.
Using the 3/16” drill bit, drill into the bench seat at the point
where the line made in step 8.4. intersects with the vertical
line made in step 8.2.
NOTE: It is not necessary to drill through the bench seat
at this intersect.
8.7.
Using the hardware supplied, the 3/8” wrench and the
Phillips head bit, install the keeper.
ACCESSORY INSTALLATION
INSTRUCTIONS
Page
4
of 5
BUCKET SPORT SEAT
Installation Instructions for the 130 & 160 Super Sport
Issue Date
06/15/2018
Rev. D
8.8.
Using the tape measure, measure
16.5 (13SPT) 19” (16SPT) inboard from
the starboard aft edge
of the bench seat.
NOTE: Assure that the keepers
line up directly opposite
each other.
8.9.
Repeat steps 8.2. through 8.7.
8.10.
Tilt the bucket sport seat forward and hook the bottom
lip under the forward edge of the bench seat.
NOTE: There is a depression in the back of the
molded piece which the installed keeper will
fit into so that the seat can rest flush against
the edge of the bench.
ACCESSORY INSTALLATION
INSTRUCTIONS
Page
5
of 5
BUCKET SPORT SEAT
Installation Instructions for the 130 & 160 Super Sport
Issue Date
06/15/2018
Rev. D
8.11.
Pull the elastomer latch down and over the
keeper to secure the seat.
8.12.
Install the warning label next to aft keeper as
shown.
Bucket Sport Seat Installation Is Complete
NOTE: To reverse the seat, unhook the elastomer latch, rotate the seat
180 degrees and repeat steps 8.10. and 8.11.
NOTE: To install the bucket sport seat on the port side of the bench seat
correctly it is important that both the forward and aft keepers are
centered 16.5 (13SPT) 19” (16SPT) from the port edge of the bench.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Boston Whaler 130 Super Sport Bucket Sport Seat Installation guide

Boston Whaler
Brand
Boston Whaler
Model
130 Super Sport Bucket Sport Seat
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents