2. DIODE LED
  3. SPOTMOD® TILE LED Fixture

DIODE LED SPOTMOD® TILE LED Fixture Installation guide

  • Hello! I have analyzed the installation guide for the SPOTMOD DI-12V-SPOT-TL-** Tile. This document includes instructions for mounting the tile, wiring it using plug-in adapters or hard-wiring it with SWITCHEX dimmers, and troubleshooting tips. The tile is designed for damp locations and requires a 12VDC power supply. I'm ready to answer any questions you have.
  • Can I connect this product to a 120VAC power source?
    Can this product be installed in wet locations?
    What should I do if the fixture is flickering?
Item # Color / Finish
DI-SPOT-TL-ADP
(Not Included)
TILE DC
Adapter Cable
DI-SPOT-TLSP6
(Not Included)
Tile 6-Way Power
Splitter Box
DI-SPOT-5EXT
(Not Included)
SPOTMOD 5ft.
Extension Cable
SPOTMOD® TILE ®
READ ALL INSTRUCTIONS PRIOR TO INSTALLATION
QUICK SPECS
** Indicates CCT, CRI, nish.
• Install in accordance with the NEC and local regulations.
• This product is intended to be installed and serviced by a
qualied, licensed electrician.
• DO NOT Connect to 120VAC Power.
• This product MUST be powered with a compatible Class 2 12VDC
LED driver and has not been evaluated for use when connected
to a power source that does not comply with Class 2 voltage and
energy limited supplies.
• CAUTION: To reduce the risk of re, do not install in a compartment
smaller than 2.5 in. x 2.5 in. x 0.27 in.
• Suitable for Damp Locations. Do not install in wet locations or
outdoors.
• Attached wire leads, connectors and accessories are not rated for
in-wall installation.
• Attached wire leads are eld-cuttable.
SAFETY / WARNINGS / ATTENTION!
Input 12VDC Constant Voltage
Power 4W
Dimmable Yes
Environment Damp / Indoor
Included Models DI-12V-SPOT-TL-**
IG062816-2.0
ACCESSORIES
For hard-wired installations, cut o unused connector and strip
wire leads. This will not void product warranty or certication.
MOUNTING
1. Mount SPOTMOD TILE to surface with 2x screws (included)
and Phillips head screwdriver (not included).
1. Attach xture(s) to SPOTMOD TILE 6-Way Power Dist Splitter.
2. Attach system to 12VDC plug-in adapter.
3. Plug adapter into 120VAC electrical receptacle.
PLUG-IN ADAPTER W/ SPLITTER SYSTEM SWITCHEX® DIMMER SYSTEM
1. Turn power OFF at circuit breaker.
2. Cut o DC barrel of SPOTMOD DC Adapter Cable. Strip wires
and hard-wire to SWITCHEX Dimmer.
3. Connect adapter cable to SPOTMOD TILE.
4. Turn Power ON at circuit breaker. Refer to SWITCHEX install
guide for more information.
TROUBLESHOOTING
• Fixture does not illuminate: Check that polarity at all
connection points are secure and not reversed.
• Fixture is ickering: Ensure a compatible system is installed.
Refer to the power supply compatibility list when installing
dimming controls. Ensure all connections are properly
secured.
• Fixture is overheating: Ensure xture is installed in a well-
ventilated area.
• Fixture turns ON/OFF continuously: Ensure driver is not
overloaded.
QUESTIONS?
®
Toll Free 877.817.6028
[email protected]
www.DiodeLED.com
N (WHT)
120 VAC
~ 60Hz
V+
V−
L (BLK)
12 VDC
SWITCHEX
(Dimmer + Driver)
Ground (GRN)
SPOTMOD® TILE
DC ADAPTER CABLE
(w/ Cut off DC Barrel)
SPOTMOD® TILE
OMNIDRIVE®, REIGN® Dimmer, TOUCHDIAL™, and more installation
diagrams are available at www.DiodeLED.com.
Class 2 Low Voltage
Plug-In Adapter
AC Power
50/60Hz
SPOTMOD
®
TILE
SPOTMOD® TILE
6-Way Power Dist Splitter
Class 2 Low Voltage
Plug-In Adapter
AC Power
50/60Hz
SPOTMOD® TILE
SPOTMOD® TILE
DC ADAPTER CABLE
1. Attach xture to SPOTMOD TILE DC Adapter Cable.
2. Attach system to 12VDC plug-in adapter.
3. Plug adapter into 120VAC electrical receptacle.
PLUG-IN ADAPTER SYSTEM
/