Honda 08E92-SNA-100B User manual

Brand: Honda

Model: 08E92-SNA-100B

Category: Car media receivers

Type: User manual

FEB 2008

2006-2008 CIVIC 4-DOOR

(A/T ONLY)

REMOTE ENGINE

STARTER SYSTEM

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

Control unit bracket

Relay bracket

3 Black relays (4-pin)

18 Wire ties

Remote Engine Starter Attachment Kit

P/N 08E92-SNA-100B

Engine starter harness

Control unit

Antenna

Key ring

Protective tape

Engine starter label

Fuse label

Accessory User’s Information Manual

Quick Start Guide

PARTS LIST

Remote Engine Starter Unit Kit

P/N 08E91-E22-100B

Transmitter

AII 38216-38957

www.collegehillshonda.com

7 Foam cushion tapes

Flange nut

Clip

Green relay (5-pin)

Template

Illustration of the Engine Starter System Installed

on the Vehicle

7401010T

ENGINE STARTER

HARNESS

ANTENNA

RELAY

(5-PIN)

2 FUSES 40A

3 RELAYS

(4-PIN)

CONTROL

UNIT

2 FUSES 3A

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Long blade flat-tip screwdriver

Small flat-tip screwdriver

6 mm Hex wrench

T25 Torx bit

3 mm and 7 mm Drill bits

File

Ratchet

10 mm Socket

Combination wrench

Isopropyl alcohol

Shop towel

Tape measure

Clip remover

Diagonal cutters

Felt-tip pen

Center punch

Scissors

2 Pairs of needle nose pliers

Rubber mallet

HDS (Honda Diagnostic System)

Masking tape

Safety goggles

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

NOTE: The antenna should only be installed if the

ambient air temperature 15°C (60°F) or above.

1. Make sure you have the anti-theft code for the

radio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

www.collegehillshonda.com

Setting the Control Unit

3. Get the control unit. Using a small flat-tip

screwdriver, adjust the switches on the control

unit to the locations shown. Using a isopropyl

alcohol on a shop towel, clean the area where the

protective tape will attach. Attach the protective

tape to the control unit over the switches.

NOTE:

• The switches must be selected before the

control unit is plugged in.

• If the switch setting is not correct, the engine

starter will not operate correctly.

• If setting the switches when the control unit is

installed in the vehicle, touch a metal part of

the screwdriver to a metal part of the vehicle

to discharge any static electricity.

• If you change the switch settings with the unit

connected, you must disconnect the unit, then

reconnect it before the settings will change.

SW : 1 RR Junction Unit

SW : 2 Trunk or Tailgate

SW : 3 Smart Entry

SW : 4 Horn or Buzzer Answer Back

SW : 5 Trunk Main SW

SW : 6 Reserve

Removing the vehicle parts

4. Remove the trunk lid/fuel fill door opener cover

(six retaining tabs). Remove one self-tapping

screw.

5202191T

KEY

SELF-

TAPPING

SCREW

COVER

6 RETAINING

TABS

TRUNK LID/

FUEL FILL

DOOR OPENER

Unlock.

CONTROL

UNIT

SMALL

FLAT-TIP

SCREW-

DRIVER

Discharge any

static electricity.

The switches must

be selected before

the control unit is

plugged in.

SET

SWITCHES

SW:1 RR Junction unit -----------------------> OFF

SW:2 Trunk or Tailgate ----------------------> OFF

SW:3 Smart Entry -----------------------------> OFF

SW:4 Horn or Buzzer Answerback ------> OFF

SW:5 Trunk Main SW -------------------------> OFF

SW:6 Reserve ----------------------------------> OFF

SWITCHES

www.collegehillshonda.com

8. Remove the driver’s dashboard lower cover (eight

clips).

5202121T

DRIVER’S

DASHBOARD

LOWER COVER

8 CLIPS

7. If equipped, remove the driver’s dashboard under

cover (turn the knob counterclockwise, and

release two clips and pin).

5202112T

KNOB

DRIVER’S

DASHBOARD

UNDER COVER

2 CLIPS

6. Pull away the weatherstrip, and remove the left

kick panel (two clips).

5202220T

WEATHERSTRIP

2 CLIPS

LEFT

KICK

PANEL

4. Using the key, unlock the opener.

5. Remove the left front door sill trim (two retaining

tabs, five clips, and three hooks).

5202200T

5 CLIPS

2 RETAINING

TABS

LEFT FRONT

DOOR SILL TRIM

FRONT

3 HOOKS

www.collegehillshonda.com

9. Lower the tilt lever, and pull the steering wheel

toward you. Insert a long blade flat-tip screwdriver

along the guide of the column lower cover, and

pry the retaining tab of the column upper cover.

10. Push on the column lower cover in the area

shown to separate the column upper cover from

the column lower cover (two retaining tabs). Pull

up to remove the column upper cover (two

hooks).

6608050T

COLUMN

UPPER

COVER

2 HOOKS

TILT LEVER

COLUMN

LOWER

COVER

2 RETAINING TABS

RETAINING

TAB

LONG BLADE

FLAT-TIP

SCREWDRIVER

GUIDE

Push.

11. Remove the column lower cover (two self-tapping

screws and one screw).

5308530T

2 SELF-TAPPING

SCREWS

SCREW

COLUMN

LOWER

COVER

www.collegehillshonda.com

13. Remove the sunvisor holders. Using a small flat-

tip screwdriver, push the hook, and turn the

holder 90°, then pull it out.

12. If equipped, use a small flat-tip screwdriver to

remove the left and right lens from the map light

console (four retaining tabs for each lens).

Remove the two bolts, and then release the map

light console.

6D01400T

SUNVISOR

HOLDER

SMALL

FLAT-TIP

SCREWDRIVER

MAP LIGHT

CONSOLE

14. Remove the cap from the left sunvisor (four

retaining tabs).

5217030T

4 RETAINING

TABS

CONNECTOR

LEFT

SUNVISOR

TORX

SCREW

CAP

5006010T

FRONT PILLAR

FRONT

PILLAR TRIM

WEATHERSTRIP

CLIP

LEFT FRONT

PILLAR TRIM

STRIKE POINT

CLIP

SHOP

TOWEL

RUBBER

MALLET

Strike perpendicularly

to the vehicle.

6D01390T

LENS

FRONT

BOLTS

4 RETAINING

TABS

LENS

MAP LIGHT

CONSOLE

17. Using a rubber mallet and a shop towel, gently tap

the left front pillar trim at the position shown to

release the clip. Gently tap the pillar trim just

below the “SIDE CURTAIN AIRBAG” mark.

16. Pull away the weatherstrip from the left front pillar

trim.

15. Remove the left sunvisor (two T25 Torx screws,

and unplug the vehicle connectors).

www.collegehillshonda.com

18. Pull away the weatherstrip from the left front pillar

trim. Remove the left front pillar trim (two clips).

5202100T

2 CLIPS

LEFT FRONT

PILLAR TRIM

WEATHERSTRIP

19. Remove the clip from the left front pillar trim, and

install a new clip on the left front pillar trim.

LEFT FRONT

PILLAR TRIM

CLIP (Discard.)

NEW CLIP

5217110T

Installing the Antenna

20. Using scissors, cut out the template.

21. Secure the template to the windshield with the

tape by aligning it with the edge of the black

ceramic paint as shown.

6D01203T

SCISSORS

TEMPLATE

Cut out.

6D01210T

BLACK

CERAMIC

PAINT

WINDSHIELD TEMPLATE

TAPE

Align the end

with the end

of the black

ceramic paint.

EDGE OF

BLACK

CERAMIC

PAINT

www.collegehillshonda.com

23. Measure the antenna cable as shown. Attach the

three foam cushion tapes to the antenna cable in

the measurement shown.

24. Using isopropyl alcohol on a shop towel, clean the

area where the antenna will attach. Allow the area

to dry before proceeding.

25. Remove the adhesive backing from the antenna,

insert the antenna plate under the roof liner, and

attach the antenna to the windshield aligning the

template.

26. Remove the template.

6D01240T

ANTENNA

CABLE

FOAM

CUSHION TAPE

ANTENNA

360 mm

(14 in.)

30 mm

(1.2 in.)

30 mm

(1.2 in.)

6D01250T

ROOF LINER Clean with

isopropyl alcohol.

TEMPLATE

ADHESIVE

BACKING

ANTENNA

PLATE

22. Using two pairs of needle-nose pliers, bend the

antenna plate according to the illustration and

measurement shown.

6D01222T

SCALE

ANTENNA

8 mm

(0.3 in.)

PLATE

15 mm

(0.6 in.)

NEEDLE-NOSE PLIERS

www.collegehillshonda.com

27. Route the antenna cable under the roof liner

towards the driver’s side of vehicle, and down

along the vehicle harness. Be careful not to

crease the roof liner.

28. Continue routing the antenna cable between the

front pillar and the dashboard.

5308192T

FRONT PILLAR

DASHBOARD

ANTENNA

CABLE

6D01260T

ROOF LINER

ANTENNA

CABLE

VEHICLE

HARNESS

29. Using isopropyl alcohol on a shop towel, clean the

areas where the foam cushion tape will attach.

Under the roof liner, secure the antenna cable to

the roof panel with the two foam cushion tapes

(cut one foam cushion tape in half) in the areas

shown.

30. Secure the antenna cable to the vehicle harness

with four wire ties as shown. Do not secure the

antenna cable to the drain tube.

6D01270T

ROOF

LINER

FOAM CUSHION

TAPE (1/2)

FOAM CUSHION

TAPE

ANTENNA

CABLE

6D01410T

4 WIRE TIES

VEHICLE

HARNESS

ANTENNA

CABLE

VEHICLE

CLIP

DRAIN

TUBE

www.collegehillshonda.com

34. Install the four relays to the engine starter harness

relay blocks. Be careful to install the relays

properly, or a malfunction will result.

Routing the Engine Starter Harness

33. Attach the 3 A fuse labels to the engine starter

harness fuse case, and the 40 A fuse labels to the

fuse block.

6D01031T

CLIP

LAYOUT OF RELAYS

WHEN VIEWED FROM FRONT

40 A FUSE

LABEL

3 A

FUSE

LABEL

FUSE

BLOCK

RELAY

BLOCK

4-PIN RELAY

(black)

4-PIN

RELAY

(black)

5-PIN

RELAY

(green)

FUSE

CASE

Installing the Control Unit Bracket

32. Locate the small square hole next to the small

round hole in the dashboard support bracket.

Under the dash, attach the control unit bracket to

the vehicle bracket near the front lower pillar using

a flange nut. If the vehicle is equipped with a

moonroof, be careful not to pull on the drain tube.

31. Secure the antenna cable to the vehicle harness

with a wire tie. Secure the wire tie between the

vehicle harness branching points.

6D01281T

VEHICLE

HARNESS

WIRE TIE

ANTENNA

CABLE

BRANCHING

POINTS

6D01123T

VEHICLE

BRACKET

CONTROL UNIT

BRACKET

FRONT

FLANGE

NUT

VEHICLE

BRACKET

www.collegehillshonda.com

37. Disconnect the vehicle 8-pin connector on the rear

of the wiper switch and plug the engine starter

harness 8-pin connector into the vehicle 8-pin

connector.

38. Secure the connected 8-pin connector with a wire

tie to the engine starter harness.

6D01101T

WIPER

SWITCH

VEHICLE 8-PIN

CONNECTOR

ENGINE STARTER

HARNESS

8-PIN CONNECTOR

6D01071T

WIRE TIE

CONNECTED 8-PIN

CONNECTOR

ENGINE

STARTER

HARNESS

WIPER

SWITCH

35. Route the engine starter harness 7-pin connectors

up the steering column and to the ignition switch.

Unplug the white vehicle 7-pin connector. Plug the

white engine starter harness 7-pin connectors into

the white vehicle 7-pin connectors.

6D01081T

ENGINE

STARTER

HARNESS

7-PIN

CONNECTOR

(white)

VEHICLE 7-PIN

CONNECTOR

(white)

IGNITION

SWITCH

6D01091T

Pull the connector

and check that it

is locked securely.

VEHICLE 7-PIN

CONNECTOR (brown)

(Not reconnected.)

ENGINE STARTER

HARNESS 7-PIN

CONNECTOR (brown)

36. Unplug the brown vehicle 7-pin connector, and

plug the brown engine starter harness 7-pin

connector into the brown vehicle 7-pin connector.

NOTICE Make sure that the engine starter harness

7-pin connector is connected to the vehicle connector

and it is locked securely. A loosely connected

connector can cause engine stall during driving.

www.collegehillshonda.com

39. Wrap the vehicle 7-pin connector with one foam

cushion tape, then place the vehicle 7-pin

connector into the gap of the column.

6D01111T

VEHICLE 7-PIN

CONNECTOR

(brown)

(Squeeze into

this area.)

FOAM

CUSHION

TAPE

VEHICLE 7-PIN

CONNECTOR

VEHICLE

BRACKET

VEHICLE

HARNESS

LOCK

ENGINE

STARTER

HARNESS

WIRE

TIE

VEHICLE

HARNESS

4 WIRE

TIES

GREEN

TAPE

ENGINE STARTER

HARNESS

42. At the right of the steering shaft, locate the sub

joint box. Using a small flat-tip screwdriver, unplug

the vehicle 6-pin connector from the sub joint box.

Plug the engine starter harness 6-pin connectors

into the vehicle 6-pin connector and the subjoint

box.

43. Attach the relay blocks and fuse case on the relay

bracket.

44. Secure the engine starter harness to the vehicle

harness using a wire tie.

6D01063T

RELAY BRACKET

STEERING

COLUMN

SUPPORT

BRACKET

STEERING COLUMN

SUPPORT BRACKET

BOLT (Reuse.)

6D01162T

VEHICLE 6-PIN

CONNECTOR

ENGINE STARTER

HARNESS 6-PIN

CONNECTOR

FRONT

SUB JOINT

BOX

VEHICLE 6-PIN

CONNECTOR

VIEWED FROM

UNDERSIDE

6D01302T

FUSE

CASE

RELAY BRACKET

ENGINE STARTER

HARNESS

RELAY

BLOCK

WIRE

TIE

VEHICLE

HARNESS

40. Secure the engine starter harness to the vehicle

harness with four wire ties in the areas shown.

The lock of the wire ties should face up.

41. Remove the lower steering column support

bracket bolt. Attach the relay bracket to the

steering column support bracket and reinstall the

steering column support bracket bolt.

www.collegehillshonda.com

46. Secure the engine starter harness to the vehicle

harness using a wire tie.

• With driver's dashboard under cover: Secure

in the hole you made in the instrument panel.

• Without driver's dashboard under cover:

Secure through the existing hole for under

cover securing.

47. Use the clip on the engine starter harness to

secure the engine starter harness to the fuse box.

45. With driver's dashboard under cover: Measure

the indicated dimension on the instrument panel

and mark with a felt-tip pen and a center punch.

Drill a 3 mm hole and then a 7 mm hole at the

marked position of the instrument panel.

– Wear safety goggles during drilling.

– Using a file, remove the burrs at the edges

of the holes you made.

6D01351T

INSTRUMENT

PANEL

CENTER

PUNCH

FELT-TIP PEN

View from below

12 mm

(0.5 in.)

6 mm

(0.2 in.)

FRONT

6D01361T

INSTRUMENT PANEL

DRILL

DRILL BIT

(3 mm, 7 mm)

6D01172T

CLIP

FUSE

BOX

WIRE TIE

WITH DRIVER’S

DASHBOARD UNDER

COVER

www.collegehillshonda.com

50. Wrap foam cushion tape to the vehicle 2-pin and

4-pin connectors and secure them with a wire tie.

Then, secure the vehicle harness with a wire tie.

Reconnect the vehicle 42-pin connector.

6D01292T

4-PIN

CONNECTOR

PORT

2-PIN

CONNECTOR

PORT

FOAM

CUSHION

TAPE

VEHICLE

HARNESS

WIRE TIE

VEHICLE 2-PIN

CONNECTOR

VEHICLE

4-PIN

CONNECTOR

FUSE BOX

ENGINE STARTER

HARNESS 2-PIN

CONNECTOR

ENGINE

STARTER

HARNESS

4-PIN

CONNECTOR

Pull the connector

and check that it

is locked securely.

49. Plug the engine starter harness 4-pin and 2-pin

connectors into the fuse box.

NOTICE Check that the engine starter harness 4-pin

and 2-pin connectors are connected to the fuse box

and they are locked securely. Loosely connected

connectors can cause engine stall during driving.

48. Disconnect the vehicle 42-pin, 4-pin and 2-pin

connectors.

6D01430T

FUSE BOX

VEHICLE 42-PIN

CONNECTOR

FUSE BOX

VEHICLE 4-PIN

CONNECTOR

VEHICLE 2-PIN

CONNECTOR

FRONT VIEW

VEHICLE 2-PIN

CONNECTOR

VEHICLE 4-PIN

CONNECTOR

LOCK

VEHICLE 42-PIN

CONNECTOR

www.collegehillshonda.com

53. Install the clip from the engine starter harness to

the fuse box bracket behind the fuse box.

6D01181T

ENGINE

STARTER

HARNESS

FUSE BOX

BRACKET

CLIP

FRONT

GROUND

BOLT (Reuse.)

ENGINE STARTER

HARNESS GROUND

TERMINAL

51. Connect the engine starter harness 18-pin

connectors with each other and secure them with

a wire tie to the vehicle harness.

52. Unplug the white vehicle 14-pin connector at the

front lower pillar behind the fuse box, and plug the

engine starter harness 14-pin connectors in

between. Attach the engine starter harness 14-

pin connector to the vehicle 14-pin connector.

6D01331T

ENGINE

STARTER

HARNESS 18-PIN

CONNECTORS

WIRE TIE

VEHICLE

HARNESS

6D01141T

VEHICLE WHITE

14-PIN

CONNECTOR

ENGINE

STARTER

HARNESS

14-PIN

CONNECTOR

VEHICLE WHITE 14-PIN

CONNECTOR

FUSE BOX

54. Remove the ground bolt from the vehicle. Secure

the engine starter harness ground terminal with the

ground bolt you just removed.

www.collegehillshonda.com

60. Check that all wire harnesses are routed properly

and all connectors are plugged in.

61. Reinstall all removed parts. Check that all clips

and other fasteners are installed securely. Take

care not to pinch the airbag with a clip during

reinstallation of the front pillar trim. Do not push

the front pillar trim excessively.

62. Reconnect the negative cable to the battery.

Check that the electrical accessory and other

electrical systems function properly.

63. Perform REMOTE ENGINE STARTER

REGISTRATION, on pages 18-20, and FUNCTION

CHECK, on page 21.

64. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

65. Reset the clock.

59. Attach the engine starter label to the back of the

hood.

6D01312T

ANTENNA CABLE

TERMINAL

(Connect first.)

FRONT

CONTROL

UNIT

ENGINE STARTER

HARNESS 18-PIN

CONNECTOR

CONTROL UNIT

BRACKET

7401020T

VEHICLE

HARNESS

WIRE

TIES

ANTENNA

CABLE

58. Using isopropyl alcohol on a shop towel, clean the

area where the engine starter label will attach.

56. Install the control unit on the control unit bracket.

57. Bundle the excess antenna cable with two wire

ties and secure it with one wire tie to the vehicle

harness.

6D01421T

ADHESIVE

BACKING

ENGINE

STARTER

LABEL

HOOD

Installing the Control Unit

55. Connect the antenna cable terminal and the

engine starter harness 18-pin connector to the

control unit.

www.collegehillshonda.com

752501AS

CAR ICON

752502AS

CHECK BUTTONInput the VIN and

other required

information.

752504AS

Select

“R/C ENG STARTER.”

CHECK BUTTON

752503AS

Select

“Honda Systems.”

CHECK BUTTON

REMOTE ENGINE STARTER REGISTRATION

1. Acquire the PCM code from ISIS.

2. Connect the HDS tester to the OBD II data link

connector, then turn the ignition switch to the ON

(II) position.

3. Start the HDS, and click the car icon.

4. Input the VIN and other required information into

the HDS, then click the check button.

5. Select Honda Systems, then click the check

button.

6. Select R/C ENG STARTER and click the check

button.

www.collegehillshonda.com

752505AS

“REMARKS” message

CHECK BUTTON

752506AS

Select

“REGISTER REMOTE CONTROL

ENGINE STARTER UNIT.”

CHECK BUTTON

752507AS

“Obtain PCM-code" message

CHECK BUTTON

752509AS

Input the PCM code.

CHECK BUTTON

7. A REMARKS message will display. Click the

check button.

8. Select REGISTER REMOTE CONTROL ENGINE

STARTER UNIT, then click the check button.

9. The following message will display: Obtain PCM-

code (IMMOBILIZER PCM CODE) from iN. This

vehicle’s VIN will be required to obtain the

password. (USA). Click the check button.

10. Input the PCM Code, then click the check button.

NOTE: To ensure security, the PCM code

(password) is changed everyday, so it is

impossible to register the remote control engine

starter if the dates of the PCM code acquisition

and registration are different. The date of the HDS

tester should also be the same.

www.collegehillshonda.com

752510AS

"Registration" message

CHECK BUTTON

752511AS

“Check that the engine can be started

by the Transmitter”

CHECK BUTTON

11. The following message will display: The

registration of the Remote Control Engine

Starter Unit has been completed. Click the

check button.

12. The following message will display: Check that

the engine can be started by the Transmitter.

Click the check button.

13. Perform the function check on page 21, then

disconnect the HDS.

www.collegehillshonda.com

732904AY

DISPLAY

COMMAND

BUTTON

START

BUTTON

TRANSMITTER

STOP

BUTTON

FUNCTION CHECK

Operating Conditions

• The hood is closed.

• Shift lever is in Park.

• The key is not in the ignition switch.

• All doors and trunk are closed and locked.

Inspection

1. Within 1 second, press the command button and then the start button on the transmitter.

The engine should start if all operating conditions are met.

Does the engine start?

2. Press the command button on the transmitter, and within 1 second,

press the stop button. The engine should stop.

Does the engine stop?

3. After the engine has stopped, start the engine again, and check that the

engine stops after each of the following conditions:

NOTE:

After each test the ignition key must be cycled, or the driver’s door

must be opened and closed.

– Move the shift lever out of the P position.

– Unlock or open the doors or the trunk lid.

– Open the hood.

– Insert the key in the ignition switch.

– Press on the brake pedal.

4. Check that the power windows or the moonroof does not function when the engine is started with the transmitter.

5. Press the command button on the transmitter twice and check the vehicle condition on the display.

6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away and when the

vehicle is in direct sight.

Yes - Operation is normal.

No:

• Make sure all operating conditions are met.

• Check the engine starter harness connections.

• Connect the HDS and check for an indicated failure.

(Refer to the appropriate service manual for details.)

Yes - Operation is normal.

No - Check the engine starter harness connections.

Does the engine stop after each of these tests?

Yes - Operation is normal.

No - Check the engine starter harness connections.

www.collegehillshonda.com

Honda 08E92-SNA-100B User manual

Brand: Honda

Model: 08E92-SNA-100B

Category: Car media receivers

Type: User manual

Download PDF

report

Honda 08E92-SNA-100B User manual

Honda 08E92-SNA-100B User manual

Related papers

Other documents