Honda 08A57-SJC-100 User manual

Brand: Honda

Model: 08A57-SJC-100

Type: User manual

This manual is also suitable for

08B21-SJC-102

Honda 08A57-SJC-100 allows the driver to see objects behind their vehicle. This enables greater awareness of the surroundings when reversing, which can help avoid collisions with unseen objects.

INSTALLATION

INSTRUCTIONS

Accessory Application Publications No.

Issue Date

MAY 2007

2006-2008 RIDGELINE

REAR CAMERA

ATTACHMENT

(EX-L WITH NAVI)

AII 36587

08B21-SJC-1010-91

PARTS LIST

Attachment Kit

P/N: 08B21-SJC-102

Rear camera trim

Rear camera bracket

Rear camera subbracket

Harness clamp bracket A

Harness clamp bracket B

Rear camera subharness

Template

19 Wire ties

10 Small wire ties

6 Wire ties with clip

6-Pin connector

Grommet

2 Clear adhesive tapes

3 Blind nuts

www.collegehillshonda.com

2 EPT sealers

4 Cushion tapes

2 Socket bolts, 4 x 10 mm

3 Washer screws, 4 x 12 mm

2 Washer screws, 4 x 6 mm

Rear camera

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

10 mm Combination wrench

Ratchet

10, 12 mm and 14 mm Socket

Torque wrench

File

Isopropyl alcohol

Shop towel

Tape measure

Drill

3 mm, 8 mm, and 10 mm Drill bits

Utility knife

T40, and T50 Torx bit

KTC trim tool

Scissors

Tape

Electrical tape

Wire

3 mm Hex wrench

Illustration of the Rear Camera Installed on the

Vehicle

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by

skilled technicians who have the proper tools,

equipment, and training to correctly and safely add

equipment to your vehicle. These procedures

should not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for the

radio, then write down radio station presets.

2. Disconnect the negative cable from the battery.

7 Clips

Round grommet

6 Oval grommets

Accessory user’s information manual

Rear Camera Kit (sold separately)

P/N: 08A57-SJC-100

4712100

NAVI CONTROL UNIT

REAR CAMERA

SUBHARNESS

6-PIN CONNECTOR

REAR

CAMERA

GROMMET

www.collegehillshonda.com

3. Remove the fuel fill door release handle. Remove

the left front door sill trim (three clips and three

retaining tabs).

4. Remove the left rear door sill trim (three clips and

four retaining tabs).

5. Pull away the weatherstrip from the B-pillar lower

trim panel. Remove the left seat belt lower anchor

bolt cover and remove the lower anchor bolt.

Remove the left B-pillar lower trim panel by

pulling out toward you as shown.

• Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

6. Remove the driver’s seat frame rear cover (two

clips and two hooks).

3916041

RETAINING

TABS

RETAINING

TAB

LEFT FRONT

DOOR SILL TRIM

3 CLIPS

FRONT

FUEL FILL DOOR

RELEASE HANDLE

FRONT

RETAINIG

TABS

3 CLIPS

LEFT REAR

DOOR SILL TRIM

RETAINIG

TABS

4212450

4713010K

DRIVER’S SEAT

2 HOOKS

DRIVER’S SEAT

FRAME REAR COVER

2 CLIPS

4212330

FRONT

LEFT

B-PILLAR

LOWER

TRIM

PANEL

LEFT SEAT BELT

LOWER ANCHOR BOLT

WEATHERSTRIP

(Pull away.)

LOWER ANCHOR

BOLT COVER

www.collegehillshonda.com

9. Remove the rear seat belt anchor bolt and eight

seat anchor bolts.

• Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

8. Remove the rear seat bracket covers;

• Remove the left and right rear seat bracket

covers (two clips for each cover).

• Remove the center seat bracket cover (two

clips and nine retaining tabs).

7. Lift up the rear seats, and remove the rear seat

under covers;

• Remove the right rear seat under cover (four

clips).

• Remove the left rear seat under cover (five

clips).

10. Remove the cap from the rear trim panel cover

(four retaining tabs for each cover), and remove

the rear seat.

LEFT REAR

SEAT UNDER

COVER

RIGHT REAR

SEAT UNDER

COVER

RIGHT REAR

SEAT CUSHION

9 CLIPS

LEFT REAR

SEAT CUSHION

4212342

4212460

CLIPS

RIGHT REAR

SEAT BRACKET

COVER

CENTER SEAT

BRACKET

COVER

2 CLIPS

9 RETAINING

TABS

LEFT REAR

SEAT BRACKET

COVER

CLIPS

4 RETAINING

TABS

CAP

4 RETAINING

TABS

CAP

REAR SEAT

4212371

4212362

8 SEAT

ANCHOR

BOLTS

REAR SEAT

BELT ANCHOR

BOLT

www.collegehillshonda.com

11. Remove the rear trim panel cover (eight clips and

two retaining tabs).

14. Remove the left rear lower anchor bolt cover, and

remove the left rear seat belt lower anchor bolt.

• Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

12. Remove the left rear seat belt upper anchor bolt

cover (four retaining tabs), and remove the left

rear seat belt upper anchor bolt.

• Seat belt anchor bolt torque:

30 to 35 N·m (22 to 25 lbs)

13. Remove the left rear pillar upper trim.

• With side airbag; pull the clip, and remove the

left rear pillar trim by releasing the one clip.

• Without side airbag; remove the left rear pillar

trim by releasing the two clips.

15. Remove upper clip, then pull the left rear pillar

lower trim out toward you to release two clips.

16. Remove the left rear taillight (two bolts, two clips

and vehicle connector). Remove the right taillight

the same way.

4715601

CLIP

LEFT REAR

SEAT BELT

ANCHOR BOLT

COVER

CLIP

4 RETAINING

TABS

LEFT REAR PILLAR

UPPER TRIM

LEFT REAR SEAT

BELT UPPER

ANCHOR BOLT

2 TABS

3924012H

LEFT SIDE RIGHT SIDE

VEHICLE

CONNECTOR

VEHICLE

CONNECTOR

2 CLIPS

BOLTS

VEHICLE

CONNECTOR

LEFT

TAILLIGHT

4715611

CLIP

2 CLIPS

LEFT REAR

LOWER

ANCHOR

BOLT COVER

LEFT REAR

SEAT BELT

LOWER

ANCHOR

BOLT

LEFT REAR

PILLAR

LOWER TRIM

4212381

6 CLIPS

REAR TRIM

PANEL COVER

CLIPS

2 RETAINING

TABS

www.collegehillshonda.com

17. Remove the rear bumper:

• Remove the license plate (two bolts).

• Remove two bolts, six self-tapping screws and

six clips from the rear bumper.

• Pull the rear bumper toward you. Unplug the

two vehicle connectors, and remove the rear

bumper.

• Set the rear bumper on the blanket.

18. Remove the rear roof trim:

• Remove the roof trim nut covers (two retaining

tabs for each cover).

• Remove the two nuts.

• Using a KTC trim tool, carefully pry up the

front of the trim to release the three front clips.

Start with the left clip and work towards the

right clip.

• Gently left the front of the trim to release the

four rear clips.

• Remove the antenna grommet from the roof,

unplug the vehicle connector, and remove the

rear roof trim.

4D19051

ROOF TRIM

NUT COVER

2 RETAINING

TABS

2 NUTS

REAR ROOF TRIM

4804024

REAR

ROOF TRIM

ANTENNA

GROMMET

2 HOOKS

2 VEHICLE

CONNECTORS

HIGH-MOUNT

BRAKE LIGHT

GROMMET

4D19062

LEFT CLIP

(Start here.)

CENTER CLIP

(Second.)

RIGHT CLIP

(Finish here.)

7 CLIPS

KTC TRIM TOOL

4 CLIPS

3003063

2 BOLTS

8 SELF-

TAPPING

SCREWS

6 CLIPS

REAR

BUMPER

BOLTS

LICENSE PLATE

2 VEHICLE

CONNECTORS

www.collegehillshonda.com

22. Remove the left front anchor (two TORX bolts).

21. Remove the left C-pillar outer trim (slide

rearward, and unplug the vehicle connector).

Remove the clips from the body, and reinstall the

clips to the left C-pillar outer trim.

19. Remove and discard the grommets from the roof

panel, and install the six oval grommets and one

round grommet into the roof panel.

20. On the rear roof trim backside, remove and discard

the clips from the rear roof trim, and install the

seven clips to the rear roof trim.

4D20501

REAR ROOF TRIM

7 CLIPS

(Discard.)

4610041

T50 TORX

BOLTS

LEFT FRONT

ANCHOR

4611021

3 CLIPS

(Remove.)

3 CLIPS

(Install.)

LEFT C-PILLAR

OUTER TRIM

LEFT C-PILLAR

OUTER TRIM

VEHICLE PANEL

VEHICLE

CONNECTOR

4D20510

GROMMET

(Discard.)

ROUND

GROMMET

ROOF PANEL

6 OVAL

GROMMETS

6 GROMMETS

(Discard.)

www.collegehillshonda.com

24. Remove the left bed rail trim:

• Remove the screw cover (four retaining tabs).

• Remove the self-tapping screw.

• Pull the left bed rail trim back to release the

six clips, and remove the left bed rail trim.

25. Remove the left lower bed light (one self-tapping

screw, pull the light out towards you and unplug

the vehicle connector).

23. Remove the front bed panel (six TORX bolts).

27. Remove the left side bed panel (six TORX bolts).

26. Remove the left rear anchor (two TORX bolts).

3929032

FRONT BED

PANEL

6 T40 TORX

BOLTS

3926071

SCREW

COVER

4 RETAINING

TABS

LEFT BED

RAIL TRIM

6 CLIPS

SELF-

TAPPING

SCREW

LEFT BED

RAIL TRIM

3926021

6 T40 TORX

BOLTS

LEFT SIDE

BED PANEL

3926062

SELF-TAPPING

SCREW

LEFT LOWER

BED LIGHT

CLIP

VEHICLE

CONNECTOR

T50 TORX

BOLT

LEFT REAR

ANCHOR

www.collegehillshonda.com

28. Remove the tailgate trim:

• Remove the four screws and release the one

end clip on each side.

• Sharply push the tailgate to the right to release

the 16 clips from the trim.

• Remove the 16 clips from the tailgate and

reinstall the 16 clips to the tailgate trim in the

direction shown.

31. Center punch the tailgate at the marks on the

template. Remove the template.

30. Get the template. Using a scissors, cut out the

marked area from the template. Align the edge of

the template with the edge of the tailgate as

shown, and attach it to the tailgate tape.

29. Remove the tailgate panel (seven TORX screws).

4605080

4 SELF-

TAPPING

SCREWS

2 CLIPS

TAILGATE TRIM

16 CLIPS

TAILGATE

TRIM

4605090

7 T40 TORX

SCREWS

TAILGATE

PANEL

4707041

OUTER

TAILGATE

CUT

TEMPLATE

9 TAPES

TEMPLATE

CUT

AREA

TAILGATE

UPPER

HANDLE

4708010K

CENTER

PUNCH

CUT

TEMPLATE

TAILGATE

4 MARKS

TAILGATE

UPPER

HANDLE

www.collegehillshonda.com

33. Install one blind nut into each 8 mm hole.

34. Remove the four screws from the rear camera.

Route the rear camera harness through the rear

camera subbracket, and install the rear camera

subbracket to the rear camera with the four

screws.

35. Attach a piece of wire to the terminals from the

rear camera harness, and tape the wire to the

terminals.

32. Drill three 8 mm holes and one 10 mm hole in the

tailgate.

• Wrap tape around a 3 mm drill bit, and 8 mm

drill bit and a 10 mm drill bit 10 to 15 mm from

the end or use a drill stop.

• While wearing eye protection, drill a 3 mm

hole, then an 8 mm hole in all four locations.

Drill a 10 mm hole only in the upper center

hole.

• Remove any burrs, and apply touch-up paint

to all of the holes.

4708021

DRILL

DRILL BIT

(3 mm 8 mm)

TAILGATE

4 MARKS

TAPE

(Wrap tape around

the drill bit.)

DRILL BIT

10 ~ 15 mm

UPPER

CENTER

HOLE

DRILL BIT

(3 mm 8 mm

10 mm)

4708050

REAR

CAMERA

REAR CAMERA

SUBBRACKET

REAR CAMERA

HARNESS

4 SCREWS

4708030

TAILGATE

3 8 mm

HOLES

BLIND

NUTS

4913020

TERMINALS

TAPE

WIRE

REAR CAMERA

HARNESS

www.collegehillshonda.com

36. Route the rear camera harness through the 10 mm

hole in the tailgate, and seat the grommet into the

10 mm hole.

38. Align the two locating tabs on the rear camera

subbracket with the slots in the rear camera

bracket, and install two 4 x 6 mm washer-screws.

NOTE: Make sure the flat surface of the rear camera

subbracket is facing up: otherwise, the camera view

will be upside down.

37. Install the rear camera bracket to the three blind

nuts with three 4 x 12 mm washer-screws.

4708041

BLIND

NUT

4 x 12 mm

WASHER

SCREWS

TAILGATE PANEL

REAR CAMERA

BRACKET

4708081

4 x 6 mm

WASHER

SCREW

REAR CAMERA

SUBBRACKET

(Flat surface

facing up.)

REAR CAMERA

BRACKET

4 x 6 mm

WASHER

SCREW

2 SLOTS

2 LOCATING

TABS

4708071

REAR CAMERA

HARNESS

10 mm

HOLE

GROMMET

WIRE

VEHICLE PANEL

www.collegehillshonda.com

40. Route the rear camera harness along the tailgate

as shown.

41. Remove the TORX bolt from the tailgate hinge, and

attach the harness clamp bracket B to the

tailgate using the TORX bolt you just removed. Do

not tighten the TORX bolt at this time.

39. Install clear adhesive tapes to the tailgate:

• Open the tailgate.

• Get the clear adhesive tapes. Using scissors,

cut 30 mm from the end of each adhesive

tape.

• Using isopropyl alcohol on a shop towel, clean

the tailgate where the adhesive tapes will

attach.

4N09043

TAILGATE

REAR

30 mm

TAILGATE

LIP

TAILGATE

CLEAR

ADHESIVE

TAPE

CLEAR

ADHESIVE

TAPE

30 mm

FIRST

ADHESIVE

TAPE

SECOND

ADHESIVE TAPE

5D10010

T50 TORX BOLT

(Do not tighten at this time.)

HARNESS CLAMP

BRACKET B

TAILGATE

HINGE

TAILGATE

4708092

REAR

TAILGATE

REAR CAMERA

HARNESS

www.collegehillshonda.com

42. Secure the rear camera harness to the harness

clamp bracket B with three small wire ties. Attach

the wire tie over the tape attached to the

harness.

45. Pull the rear camera harness out from the inside

of the tailgate, and secure the rear camera

harness to the harness clamp bracket A with one

small wire tie.

43. Torque the T50 TORX bolt to 29 to 32 N·m (21 to

23 lbs).

44. Close the tailgate. Remove the lower outboard

hinge bolt, and attach harness clamp bracket A to

the tailgate hinge with the TORX bolt you just

removed. Do not tighten the TORX bolt at this

time.

46. Torque the T50 TORX bolt to 29 to 32 N·m (21 to

23 lbs).

47. Using isopropyl alcohol on a shop towel, clean the

tailgate where the cushion tapes will attach. Using

scissors, cut one cushion tape in half. Secure the

rear camera harness to the tailgate with two half

cushion tapes and two full cushion tapes at the

locations shown.

5D10020

100 mm

25 mm

TAPE

SMALL

WIRE TIE

REAR

CAMERA

HARNESS

CLAMP

BRACKET B

T50 TORX BOLT

(Torque to 29 to32 N·m)

SMALL

WIRE TIE

(Attach over

the tape.)

5D10030

TAIL GATE

HINGE

HARNESS

CLAMP

BRACKET A

T50 TORX BOLT

(Do not tighten at this time.)

5D10041

TAIL

GATE

REAR

CAMERA

HARNESS

SMALL

WIRE TIE

HARNESS

CLAMP

BRACKET A

T50 TORX

BOLT

(Torque to

29 to32 N·m)

130 mm

4N09050

CUSHION TAPE

REAR CAMERA

HARNESS

REAR

CUSHION TAPE

(Cut in half.)

TAILGATE

www.collegehillshonda.com

51. Route the rear camera harness out through the

bed panel hole, and secure the rear camera

harness to the vehicle harness with one wire tie

just inside the panel hole.

52. Route the rear camera harness along the vehicle

harness towards the front of the vehicle, and

secure it to the vehicle harness with six wire ties

in the areas shown.

48. Secure the rear camera harness to the tailgate

with five wire ties with clip.

50. Route the rear camera harness through the left

side vehicle panel hole, and secure the rear

camera harness to the vehicle harness with two

wire ties.

49. Using isopropyl alcohol on a shop towel, clean the

tailgate where the cushion tape will attach. Using

scissors, cut one cushion tape in half. Secure the

rear camera harness to the tailgate with one half

cushion tape.

4708103

5 WIRE TIES

WITH CLIP

TAILGATE

REAR

TAILGATE

REAR CAMERA

HARNESS

CUSHION TAPE

(Cut in half.)

5D10050

WIRE TIES

VEHICLE

HARNESS

REAR CAMERA

HARNESS

LEFT SIDE

VEHICLE

PANEL HOLE

4709050

WIRE

TIE

VEHICLE

HARNESS

FRONT

BED PANEL HOLE

REAR

CAMERA

HARNESS

LEFT SIDE

VEHICLE

PANEL

4709062

VEHICLE

HARNESS

6 WIRE TIES

REAR CAMERA

HARNESS

www.collegehillshonda.com

53. Remove the vehicle grommet from the left

C-pillar.

54. Insert the rear camera harness through the

grommet, and route the rear camera harness

through the vehicle grommet opening. Seat the

grommet into the grommet hole.

55. Using electrical tape, secure the grommet to the

rear camera harness, and pay attention to the

angle of the grommet.

56. Inside the passenger’s compartment turn down the

rear panel insulator. Pull the rear camera harness

out from the hole in the C-pillar, and remove the

tape and wire from the rear camera harness.

59. Route the rear camera subharness forward along

the vehicle harness, and secure the subharness

to the vehicle harness with five wire ties.

57. Remove the lock from the 6-pin connector. Plug

the rear camera harness terminals into the 6-pin

connector as shown. Reinstall the lock.

58. Get the rear camera subharness. Plug the rear

camera subharness 6-pin connector into the rear

camera harness 6-pin connector, and secure the

connected 6-pin connectors to the vehicle

connectors with two wire ties.

4709071

VEHICLE

GROMMET

VEHICLE

GROMMET

OPENING

REAR

CAMERA

HARNESS

BED BULKHEAD

REAR

CAMERA

HARNESS

WIRE

LEFT C-PILLAR

4712012K

FRONT

VEHICLE PANEL

OPENING

REAR CAMERA

HARNESS

6 TERMINALS

TAPE

6-PIN

CONNECTOR

6-PIN

CONNECTOR

Red/

Red

6-PIN

CONNECTOR

Black/

Black

Brown

Blue/

Black

White/

White

Yellow/

Yellow

WIRE

LOCK

Harness side

view

4712031

FRONT

VEHICLE

HARNESS

VEHICLE

CONNECTOR

REAR CAMERA

HARNESS

6-PIN

CONNECTOR

REAR CAMERA

SUBHARNESS

WIRE TIES

REAR CAMERA

SUBHARNESS

6-PIN

CONNECTOR

WIRE TIE

2 WIRE

TIES

4709080

TAPE

GROMMET

REAR

CAMERA

HARNESS

VEHICLE

GROMMET

OPENING

DOWN

C-PILLAR

GROMMET

www.collegehillshonda.com

63. Slide the driver’s seat back and forth to check that

the rear camera subharness is not pulled too tight

or is too loose.

62. Plug the rear camera subharness 6-pin connector

into the Navi control unit.

61. Route the rear camera subharness along the

vehicle harness and under the floor carpet, then

pull the rear camera subharness out from under

the floor carpet opening under the driver’s seat.

Secure the rear camera subharness to the

vehicle harness with two wire ties.

60. Continue routing the rear camera subharness

forward along the vehicle harness, and secure

the subharness to the vehicle harness with four

small wire ties.

4712041

FRONT

SMALL

WIRE

TIES

VEHICLE

HARNESS

REAR CAMERA

SUBHARNESS

DRIVER’S

SEAT

REAR CAMERA

SUB HARNESS

6-PIN CONNECTOR

NAVI

CONTROL

UNIT

4713030

4713040

DRIVER’S

SEAT

Check that the

rear camera

subharness is not

pulled too tight

when the seat is

moved back and

forth.

4N10010

DRIVER’S

SEAT

VEHICLE

HARNESS

REAR CAMERA

SUBHARNESS

FLOOR CARPET

OPENING

WIRE

TIES

www.collegehillshonda.com

64. Reconnect the negative cable to the battery. Turn

the key to the ON (II) position, and enter the Navi

code.

65. Move the shift knob to the “R” position.

66. Loosen the two 4 x 6 mm washer-screws. Adjust

the rear camera angle up or down so that the end

of the rear bumper is reflected at the lowest

possible end of the navigation monitor. Tighten

the two 4 x 6 mm washer-screws. Install the rear

camera trim to the rear camera bracket with two 4

x 10 mm socket bolts.

67. Turn the key to the off position.

68. Measure and mark the rear bumper at the location

shown.

71. Check that all wire harnesses are routed properly

and all connectors are plugged in.

72. Enter the customer’s radio anti-theft code, and

reset the radio station presets.

73. Set the clock.

74. Check the operation of the rear camera according

to the owner’s manual provided.

75. Put the rear camera Owner’s Manual in the glove

box with the vehicle owner’s manual.

76. Reinstall all removed parts.

NOTE: Whenever the battery is disconnected, the

driver’s window AUTO function is disabled.

77. Start the engine. Push down fully on the driver’s

window switch until the window is fully open.

78. Pull up fully on the driver’s window switch to close

the window completely, then hold the switch for

2 second or more.

79. Test the window AUTO function.

69. Using a utility knife, cut and remove measured

piece from the rear bumper. Remove any burrs

from the cut area with a file.

70. Reinstall the rear bumper.

4N15011K

REAR

BUMPER

Cut off.

10 mm

15 mm

3 mm

5D10060

4 x 10 mm

SOCKET BOLTS

REAR CAMERA

TRIM

REAR

CAMERA

Adjust the angle.

REAR CAMERA

BRACKET

2 4 x 6 mm

WASHER SCREWS

www.collegehillshonda.com

Honda 08A57-SJC-100 User manual

Brand: Honda

Model: 08A57-SJC-100

Type: User manual

This manual is also suitable for

08B21-SJC-102

Honda 08A57-SJC-100 allows the driver to see objects behind their vehicle. This enables greater awareness of the surroundings when reversing, which can help avoid collisions with unseen objects.

Download PDF

report

Honda 08A57-SJC-100 User manual

This manual is also suitable for

Honda 08A57-SJC-100 User manual

Related papers

Other documents