Barco OLite 510 Installation guide

Barco
Brand
Barco
Model
OLite 510
Category
Rack accessories
Type
Installation guide

This manual is also suitable for

Vertical & horizontal locks
Installation manual
For OLite rental frame structure
R5976996/00
23/05/2006
Barco nv Events
Noordl
aan 5, B-8520 Kuurne
Phone: +32 56.36.89.70
Fax: +32 56.36.88.24
E-mail:
[email protected]
Visit us at the web: www.barco.com
PrintedinBelgium
1. OLite rental frame truss beam
1. OLITE RENTAL FRAME TRUSS BEAM
Types of locks
A single truss bean has two locks, o ne on the left and on e the right side. The procedure described below is for the left lock handle.
Handle in the same way for the right lock handle. The screw position is mirrored in comparison with the left side.
A dual truss bean has 4 locks, one on the left, one on the right side and two in the middle. The procedure the side locks is the same
as for a single truss. For the center locks, procedure one must be skipped as there is no cover plate.
1.1 Removing the cover plate vertical l ock handle
How to remove
1. Turn out both screws A.
A
B
C
Image 1-1
Removing cover plate
2. Turn out the 4 screws C.
3. Take off the co ver plate.
1.2 Removing the locking blocks
How to remove
1. Turn out the 5 screws (A) mounted on the bo
ttom side of th e truss.
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
1
1. OLite rental frame truss beam
A
B
Image 1-2
Locking blocks
2. Take off the locking blocks which are still tight together with an interlocking plate.
1.3 Removing the handle
How to remove
1. Pull the handle backward s (A).
A
B
C
D
Image 1-3
Removing handle
2. Turn the handle (B) in the direction of gap C in the front plate so that the pin on the handle (D) can pass through hole C.
1.4 Ins erting a new handle
How to mount
1. Insert the ha ndle in gap (C).
2
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
1. OLite rental frame truss beam
B
C
A
D
F
Image 1-4
Mounting the handle
2. Turn the h andle in such a way that pin (B) can pass gap (C).
3. Push it further in, turn it back until pin (B) is pointing to the top of the truss beam and push it till pin (B) is against the block.
1.5 Mounting the locking blocks
How to mount
1. Place block assembly B on its place.
A
B
Image 1-5
Mount locking blocks
Note: O nly possible with a fully inserted handle.
2. Turn in the 5 screws.
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
3
1. OLite rental frame truss beam
1.6 Moun ting the cover plate
Only for th e side locks. The center lo cks have no cover plate.
How to mount
1. Place cover plate (C) on the locking blocks.
A
B
C
Image 1-6
Mounting the cover plate
2. Turn in the 4 screws (B).
3. Turn in bot h screws (A).
4
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
2. OLite rental frame vertical locks
2. OLITE RENTAL FRAME VERTICAL LOCKS
Each tile has 2 vertical locks, a left and a righ t lock. Th e g iven procedures are giv en for a right lock. The left
lock is a m irror of the right lock.
2.1 Removal of vertical locking assembly
How to remove
1. Turn out the 3 screws on the bottom side (A).
D
A
B
C
Image 2-1
Remove vertical locking assembly
2. Turn out both screws on the front side of the v e
rtical locking (B).
3. Turn off bolt C.
4. Set the locking handle upwards.
5. Slide the vertical locking assemb ly forward to remove it.
2.2 Mounting the vertical locking assembly
Before turning in a screw, put a lick of glue on the screw.
How to mount
1. Insert the vertical locking assembly (A) on its place with the handle upwards.
Slide the hammer bolt (B) a little upwards, if it is necessary, so that it matches the hole in the front plate
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
5
2. OLite rental frame vertical locks
A
B
E
D
C
Image 2-2
Mounting vertical lock assembly
2. Turn a nut (C) on t he ha mmer bolt (B).
3. Turn in both front screws (D).
4. Secure the position by turning in the 3 bottom screws E.
6
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
3. OLite rental frame horizontal locks
3. OLITE RENTAL FRAME HORIZONTAL LOCKS
3.1 Getting access to the locks
How to get access
To have easy access to the horizontal lock fixation screws, take out 2 modules on each side.
To take out an OLite modules, follow the procedure “R eplace an OLite module on-site” as de scribed in the OLite display service
manual (R5976892) or installation manual (R5976832).
3.2 Removing t he horizontal lock with hook
How to remove
1. Turn out the screw securing the handle.
Image 3-1
Horizontal lock handle
2. Slide out th e handle.
3. From the front side, turn out both fixation screws of the fastener.
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
7
3. OLite rental frame horizontal locks
Image 3-2
Removing fastener
3.3 Removing the horizontal lock without hook
How to remove
1. From front side of the tile, turn out both fixation screws.
Image 3-3
Removal horizontal lock
2. Slide out the horizontal lock on the side of the tile.
3.4 Mounting the horizontal lock without hook
How to mount
1. Insert the side lock with the closing bar (A) to the top.
8
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
3. OLite rental frame horizontal locks
A
Image 3-4
Mounting the horizontal lock
2. Insert from the front side of th e tile both fixation screws and secure the horizontal lock position.
3.5 Mounting the horizontal lock with hook
How to mount
1. Insert the s ide lock with the hook fixation points (A) in th e upper part of the assembly.
A
Image 3-5
Mounting horizontal lock
2. Insert from the front side of th e tile both fixation screws and secure the horizontal lock position.
3. Insert the axis for the hook into the hook axis.
4. Slide the hand le on the axis and faste n the screw.
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
9
3. OLite rental frame horizontal locks
3.6 Reinstall the removed OLite modules
How to reinstall
For more information, see Installation manual or Service manual for OLite displays.
10
R5976996 VERTICAL & HORIZONTAL LOCKS 23/05/2006
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Barco OLite 510 Installation guide

Barco
Brand
Barco
Model
OLite 510
Category
Rack accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents